REESE LIBRARY MI i'ii i . UNIVERSITY OF CALIFORNI Deceived ztftress/oiis No. UNIVERSITY COMPRESSED AIR PRACTICAL INFORMATION UPON AIR-COMPRESSION AND THE TRANSMISSION AND APPLICATION OF COMPRESSED AIR. BY FRANK RICHARDS, MEM. A.S.M.E. FIXST EDITION'. FIRST THOUSAND. VE T RSITT) OF jr NEW YORK : JOHN WILEY & SONS. LONDON: CHAPMAN & HALL, LIMITED. 1895. Copyright, 1895, BV FRANK RICHARDS. ROBERT DRUMMOND, ELKCTROTYPER AND 1'RINTER. NEW YORK. PREFACE. IT is only proper to say that much of the matter con- tained in the following pages has appeared at intervals dur- ing the past two years in the columns of the American Machinist. The publicatibn oV'the articles referred to and the remarks which they have elicited have served to em- phasize to me the too evident fact of the general scarcity of practical information about air-compression and the uses of compressed air, and the wide diffusion of misinfor- mation and prejudice upon this subject. In spite of it all the use of compressed air is rapidly spreading, and every- where with satisfaction to the users. I would gladly do what I can to extend the field of its usefulness, and I have so much faith in its powers that I believe that the best of all ways to advertise it is simply to tell the straight truth about it, and that I have tried to do. FRANK RICHARDS. NEW YORK, May, 1895. iii COMPRESSED AIR CHAPTER I. MECHANICAL VERSUS COMMERCIAL ECONOMY. BEFORE considering the conditions under which air may be most economically compressed, having regard to the power cost alone, and the conditions relating to the trans- mission and application of the air, so that the most power may be realized, it seems proper to say something of the many applications of compressed air where the question of the actual power cost of the air, or of the actual amount of power realized from the air, seems to have little to do with the case. This is like asking a suspension of judg- ment, or a reservation of final decision upon the claims of compressed air, until the whole case has been presented ; and it seems to be rather necessary, because so many have fallen into the habit of thinking only of the losses of power in the use of compressed air, and of arguing that because certain losses are proven, that therefore the employment of compressed air is not to be considered for any purpose. There are many men even in these days, and many intelli- gent engineers among them, who, to their own loss, will not COMPRESSED AIR. consider the claims of compressed air as a means of power transmission, because their minds have been so filled with this idea that its use entails enormous losses. That con- sideration settles it for them, and that is the libel from which compressed air suffers, so that it does not get a fair chance even to show what it can do. It is only another case of giving a dog a bad name ; and in this case it is a very good dog with a very bad name. It is the worst kind of a case to set right, and often the dog dies before justice is secured. In this case, however, there is not the slightest possibility of killing the dog or of shutting him out of sight, and the public cannot fail in the end to get hold of the facts as they are. The attitude of compressed air before the mechanical public, and especially the American mechanical public, has been a peculiar one all the way through. It has had no disinterested, all-around friends to look after its interests, nor interested ones either. There have been no men, and still less has there been any company of men, who have made the application of compressed air their business and have looked after it. Where is the General Compressed- Air Com- pany, in fact as well as in name, performing for compressed air such functions as more than one company are performing for electricity, and why is there not such a company ? Of the builders of air-compressors not one of them has been, not one of them is to this day, responsible for the econom- ical application of compressed air after the compression, or apparently cares anything about it. This is not really to be wondered at, since the increase in the use of compressed air and in the demand for compressors has been so great and rapid, at least in the United States, that the compressor builders have been fully occupied in satisfying the demand. MECHANICAL VERSUS COMMERCIAL ECONOMY. 3 Where compressed air has been used in this country, and where any thought has been given to economy in its use, the air-compressor, it would seem, has been almost exclu- sively studied and talked about. In the progress of the steam-engine it has sometimes seemed that the steam-boiler has hardly received its proper share of attention. In the existing writings upon steam-engine economy it is probably safe to say that the engine engrosses ten times as much of the matter as the boiler does. In the case of compressed air the boiler, or compressor, gets ten times as much study and discussion as the engine or motor or other apparatus which uses the air. There are such vagaries of injustice in civilized communities. The impression which has got abroad of the waste of power in the use of compressed air has, curiously enough, been fostered and disseminated by the air-compressor peo- ple more than by any one else. We may say this with per- fect safety, for it strikes so generally that it hits no one in particular. The compressed air literature accessible to the general public consists principally of air-compressor cata- logues. The argument of the average catalogue runs like this : " If you are going to use compressed air for any pur- pose, look out for the enormous losses of power to be en- countered, and which you are sure to experience, if you dont buy our compressor." And the result has been that many have " caught on " to the terrible tale of the waste of power, and have helped to spread it far and wide. The argument is, of course, not maliciously meant ; but it has done more work, and somewhat different work, than that which was intended. But whether the employment of compressed air be eco- nomical or not, as far as the application of the power is 4 COMPRESSED AIR. concerned, we do not propose to investigate that subject just here. We wish rather to call attention to the many applications of compressed air where this question of power economy certainly does not apply. We may say, indeed, that in a large majority of the cases in which compressed air is used the question of power economy does not apply. Even in the use of compressed air for driving rock-drills in mines and tunnels, the field which still probably employs one half of all the compressed air that is used for mechani- cal purposes, the question of economy, or the comparative cost of operation, so far as it might determine the employ- ment or the rejection of the system, is not worth consider- ing, because in this field compressed air has no competitor, unless hand-power may be said to be one. In the use of compressed air for operating the brakes upon railway trains, a service which employs a greater number of air-compres- sors than any other line of service in the world, economy of power is not to be considered. Although it is notorious that the compressors employed for this service use five times the steam they should use for the work done, and ten times as much steam as the best-designed air-com- pressors of the present day would use for the same work, there would be no thought of throwing the air-brake off the trains if those " compressing-pumps," as they are familiarly called, used double or four times as much steam to do their work as they use now. Any one of several collateral con- siderations may easily take precedence of or assume greater weight and importance than the question of power economy in determining the employment of compressed air. The cases are few in which it is employed merely as a means of power transmission, and in competition with other means of power transmission, meeting them upon equal terms, and MECHANICAL VERSUS COMMERCIAL ECONOMY. 5 with no other consideration but that of the comparative economy with which the power is transmitted. There are many. cases that are clearly cases of power transmission, or cases of work to be done at a distance from the source of power, where the question as to whether the power is to be applied continuously or intermittently may be a most im- portant factor in the general problem. Compressed air is unique among all power transmitters at least among long- distance power transmitters in that it is always and in- stantly ready to do its work to its full capacity, and yet that it charges nothing for its services except when it is actually employed. Other transmitters may or may not propose to do the actual work a little cheaper, but they expect to be an expense to their employer for maintenance when not employed. In the pneumatic switch and signal service a single air-compressing plant is capable of operating the switches and signals upon a section of railway twenty miles long ; and when the pipes are once filled with air at the required pressure, that air does not condense or suffer loss or deteriorate in any way except as it is used. Elec- tricity makes open confession of its inability to do this intermittent work, in that while in this switch and signal service it is actually employed to give the wink to the air as to what is wanted, the air has to do the work. It need not be said that steam could not do this work, for its strength would all be turned to water before the end of the pipe was reached. How little weight the actual power economy may have in determining the employment of compressed air for a given purpose is suggested by the conditions of the pneu- matic postal service. In the cities of Europe pneumatic postal transmission has been an established commercial sue- COMPRESSED AIR. cess for years, and recently the same most gratifying experi- ence is realized at the Philadelphia post-office. The appli- cation of the air is not mechanically economical, only ten per cent of the power employed being applied to the work of moving the carriers, while ninety per cent is " wasted " in accelerating the air and in its friction. The " compressing-pump " of the air-brake service being now familiar to all railroad men, and being at hand or eas- ily procurable by all railroad shops, has been of late years always ready in those shops with its supply of compressed air, and this ready supply of compressed air has led to the general employment of it in railroad shops and in railroad service for a variety of uses. Whatever it is tried for, its use for that purpose continues, and one thing leads to an- other. These uses of compressed air in railroad shops con- tinually increase, not because the air is more adapted to railroad use than to any other, but because the air is there. Where the air is once used in one of these shops its use in- creases, the volume of air used increases, and the increas- ing demand for the air is met by setting up additional " compressing-pumps " in succession, until in some in- stances as many as eight of them have been employed to- gether to supply a single shop. It is evident here that power economy could have little to do with the case, or some thought would be given to the economical compres- sion of the air, and a good air-compressor would take the place of the air-brake pumps as a means of supply. This substitution is now in progress, we are happy to say, in many shops with most gratifying results. A recent floating paragraph tells how the master me- chanic of one of the railroads does his whitewashing by compressed air : " An old freight-car has been fitted with MECHANICAL VERSUS COMMERCIAL ECONOMY. 7 three air-brake pumps and two reservoirs," instead of one air-compressor and one reservoir or receiver, " the pumps being driven by steam from an engine (locomotive) and a pressure of 40 pounds being maintained in the reservoirs. The car and engine are run upon the track alongside the building to be whitewashed. By a system of piping the air is carried into the building, and to the long iron nozzles used by the men in applying the fluid. Each man has an iron tube with a funnel-shaped end, from which the white- wash is sprayed upon the woodwork. To each nozzle are attached two lines of hose, one supplying the air and the other the whitewash. The air rushes into the cylinder of the nozzle, and its pressure causes a suction that brings up a stream of whitewash and at the same time expels it in the form of spray." There can be no doubt of the success of this scheme ; but if it pays to use a locomotive, a freight- car, three brake-pumps, two reservoirs, and all the rest of it, for such a job, compressed air surely must be cheap at any price, or there must be economy in compressed air if eco- nomically compressed and wisely applied. As to how much the question of power economy may have to do with the remunerative use of compressed air is suggested by an article in Machinery, September, 1894, describing the various uses to which compressed air is put in the West Shore R. R. shop at Frankfort, N. Y. " It is stated that the entire power cost for running the air-com- pressors to supply the whole shop is not more than ten cents per day, while the actual saving in labor effected is from fifteen to twenty dollars per day. In the article re- ferred to, among the many applications of compressed air in the above shop mention is made of a machine for (by the aid of compressed air) putting the couplings into the 8 COMPRESSED AIR. ends of air-brake hose. " This little machine has a record of putting together one hundred in one hour and five min- utes, against twenty-five in one day by hand, and actually paid for its entire cost in one day's application." Simply give compressed air a chance and it will quickly demonstrate its value. The progress in the use of com- pressed air thus far seems plainly to indicate that its wider application is promoted more by having a supply of it ready at hand, or easy to get, than by showing how cheaply it can be furnished. Those who are introducing small, cheap compressors that work with reasonable economy are doing excellent missionary work for compressed air. Farther along, as large, permanent compressing-plants are estab- lished, we may believe that the minute economies will re- ceive the consideration which they deserve. However the air may be used, and however profitable it may be to use it, it will always be in order to get it as cheaply as possible, and economy in air-compression must always be a clear gain. OF THE UNIVERSITY CHAPTER II. DEFINITIONS AND GENERAL INFORMATION. AT the beginning it would seem to be well to get to- gether for use or reference the general facts in relation to air and to the phenomena attending its compression. As this work is intended for the greatest good of the greatest number, being for popular use, or for the use of those who will practically have to do with compressed air, and as it is in no sense for the use of expert scientists, the common standards of weight and measurement will be employed wherever it is possible to use them intelligibly. For tem- peratures the Fahrenheit scale will be used exclusively. All measures of length or distance will be given in feet and inches, and weights in pounds avoirdupois. Where pressures are referred to, they will be the pressures as indi- cated upon a common pressure gauge, or the pressures above that of the atmosphere. The absolute pressure, of course, is the gauge pressure plus the pressure of the at- mosphere at the given time and place, this atmospheric pressure being usually taken as 14.7 Ibs. at the sea-level. It will be necessary to refer to absolute pressures occasion- ally, but we trust that no misunderstanding will occur. Air is composed of 23 parts by weight of oxygen and 77 parts by weight of nitrogen. By volume the proportions are 21 parts of oxygen and 79 parts of nitrogen. Although 9 IO COMPRESSED AIR. oxygen is thus less than one quarter of the air, it is much more studied and written about and is apparently of much more use and importance than the larger constituent. It may be that the functions of nitrogen are not yet very fully or clearly understood. It certainly has not been considered deserving the study, nor has it received the attention that oxygen has received. Oxygen is the active partner in the combination. A friend who is blessed with more knowl- edge in this line than is possessed by the writer suggests that oxygen is made for the mechanic and nitrogen for the farmer. We shall frequently use the term " free air " as we go along. The term free air in contradistinction from com- pressed air is only used as a matter of convenience and custom. Free air, or air at atmospheric pressure, is really compressed air, or air subjected to pressure, as truly as air at 100 Ibs. pressure is compressed air, and its volume, press- ure, and temperature are subject to the same laws. By free air, as the term is commonly used, is meant air at atmos- pheric pressure and at ordinary temperature, and it is the air as we receive it when we begin the operation of air. compression. It is free air, or it should be free air, when first admitted to the air-compressing cylinder, and it is not free air again until it is exhausted or discharged into the atmosphere, when it has done its work and we have no further use for it or connection with it. The condition in which our free air is received is not by this general term accurately defined in any of its particu- lars, either as to pressure, volume, or temperature. The pressure and volume of the air may vary with the altitude or location, or with the barometric reading in any given location, or, again, the volume may vary with the tempera- DEFINITIONS AND GENERAL INFORMATION. II t ture. The temperature may vary with the changes of the- seasons or with the special surroundings. For general purposes we shall assume our free air to be at the usual sea- level atmospheric pressure of 14.7 Ibs., absolute, and at a temperature of 60. We shall have to refer constantly to temperatures, and, as said above, the Fahrenheit scale will be used exclusively, and usually the temperatures will be the sensible tempera- tures, or those indicated by the common Fahrenheit ther- mometer, 32 being the melting-point of ice, or the point where water changes from the solid to the liquid state, and 212 being the point where it changes from the liquid to the gaseous state. The boiling-point is in practice quite a variable one, and depends entirely upon the pressure sur- rounding the water, 212 being the boiling-point only at ordinary atmospheric pressures near the sea-level. Water may theoretically be made to boil at any temperature above the freezing-point by sufficiently reducing the atmospheric pressure to which it is exposed. The range of the Fahren- heit scale between the melting-point of ice and the boiling- point of water is 180 degrees. We shall have frequent occasion to refer to absolute tem- peratures. Absolute temperature by the Fahrenheit scale is the temperature as indicated by the thermometer plus 461 degrees. Thus at 60 by the thermometer the absolute temperature is 60 -f 461 521. At zero the absolute temperature is o + 461 = 461. At temperatures below zero the absolute temperatures are also determined in the same way, by simple addition. Thus, if the temperature by the thermometer is 30 below zero, or 30, the ab- solute temperature will be 30 -|- 461 431. In all questions relating to the volume, pressure, or weight of 12 COMPRESSED AIR. air, whether compressed or not, the absolute temperature of the air has an important bearing, as the volume of the air will vary directly as the absolute temperature, and the pressure and the weight of the air will all have changing relations. If the absolute temperature of the air is in- creased, the volume will be increased in the same pro- portion, the pressure remaining unchanged. So if the absolute temperature of the air be diminished, the vol- ume will be diminished in the same way. The relations of volume, pressure, and temperature of air are thus sum- marized : 1. The absolute pressure of air varies inversely as the volume when the temperature is constant. 2. The absolute pressure varies directly as the absolute temperature when the volume is constant. 3. The volume varies as the absolute temperature when the pressure is constant. 4. The product of the absolute pressure and the volume is proportional to the absolute temperature. A cubic foot of dry air at atmospheric pressure and at any absolute temperature will weigh 39.819 Ibs. divided by the absolute temperature. Thus at 60 a cubic foot of air weighs 39.819 -=- (60 -f- 461) = .0764 Ib. So, inversely, the volume of i Ib. of air at atmospheric pressure and at any absolute temperature may be ascertained by dividing the temperature by 39.819. Thus at 60 as before 521 -i- 39.819 = 13.084 cu. ft. The following table (I), from Appleton's Applied Me- chanics, shows the weight and volume of air at different temperatures. If the temperature and the pressure of air both vary the constant 2.7093 multiplied by the absolute pressure in Ibs. DEFINITIONS AND GENERAL INFORMATION. 13 TABLE I. TABLE OF THE WEIGHT AND VOLUME OF DRY AIR AT ATMOSPHERIC PRESSURE AND AT VARIOUS TEMPERATURES. From Applet on? s Applied Mechanics. Temperature, Degrees Fahr. Weight of One Cubic Foot in Pounds. Volume of One Pound in Cubic Feet. O .0863 11.582 10 .0845 11.834 20 .0827 12.085 30 .0811 12.336 32 .0807 12.386 40 .0794 12.587 50 .0779 12.838 60 .0764 13.089 70 .0750 13.340 80 .0736 13.592 9 .0722 13.843 IOO .0710 14.094 no .0697 14-345 120 .0685 14.596 130 .0674 14.847 I 4 .0662 15-098 150 .0651 15.350 1 60 .0641 15.601 170 .0631 15.852 1 80 .0621 16.103 190 .0612 16.354 200 .0602 16.605 210 0593 16.856 212 .0591 16.907 per sq. in. and divided by the absolute temperature will give the weight of a cubic foot. What will be the weight of i cu. ft. of air at 60 Ibs. pressure and 100 temperature? 2.7093 X (60 .+ 14.7) -4- (100 + 461) .3607 Ib. The volume of i pound of air may be obtained by di- viding the absolute temperature by the absolute pressure and dividing this by the same constant, 2.7093. 14 COMPRESSED AIR. What will be the volume of i Ib. of air at 75 tempera- ture and.5o Ibs. pressure ? (75 + 46i) -*- (50 -f 14-7) -*- 2.7093 = 3.052 Its. If the temperature of the air is changed from one ab- solute temperature T to another absolute temperature /, the volume remaining constant, the resulting absolute pressure p may be obtained from the original absolute pressure P by the simple proportion T : / : : P : p, or PX t It is not supposed that heat is an actual existence any more than sound or light is ; still it is very necessary, especially in all matters relating to compressed air, to be able to accurately measure and state the effects of heat, and to have some unit or standard of measurement and comparison. The unit of heat generally adopted is that quantity of heat that will raise the temperature of one pound of water one degree. One unit of heat if applied to one pound of anything else will not have precisely the same effect in raising the temperature that it has when applied to water. More heat is required to raise the temperature of one pound of water one degree than is required for any other substance. The heating effect of a unit of heat applied to different substances is found to vary widely, and the special quantity of heat required to raise the tempera- ture of one pound of any substance one degree is known as its specific heat. The specific heat of water being i, the specific heat of air is .2377, or the same unit of heat that would raise the temperature of one pound of water one degree would raise the temperature of one pound of air more than four degrees. The application of heat to air or to any elastic fluid may have either of two effects. It may DEFINITIONS AND GENERAL INFORMATION. I 5 increase the volume while the pressure remains constant, or it may increase the pressure while the volume remains con- stant. The specific heat will be quite different in the two cases. The specific heat of air .2377, as given above is its specific heat at constant pressure, and the heat applied in this case exhibits its effect in increasing the volume of the air. If the air be confined so that there can be no in- crease of volume, its specific heat is only .1688, or about one sixth that of water. Heat applied to air at constant volume increases the pressure of the air. If heat be applied to air under constant pressure, raising its temperature from 32 to 212, the increase in volume will be from i to 1.367 ; and if heat be applied to air at constant volume, raising its temperature, as before, from 32 to 212, the increase in absolute pressure will be from i to 1.365, the numerical result being practically alike in the two cases, but the heat expended will be as .2377 : .1688, or nearly one half more in one case than in the other. When air is compressed, or when its volume is reduced by the application of force, the temperature of the air is raised. This phenomenon occurs entirely regardless of the time employed in the compression. If during the compres- sion the air neither loses nor gains any heat by communi- cation with any other body, the heat generated by the act of compression remaining in the air and increasing its temperature, then the air is said to be compressed adia- batically, and such compression is adiabatic compression. When the pressure is removed from the air and it is allowed to expand, its temperature falls, and if the air during this operation receives no heat from without, it is said to expand adiabatically. Adiabatic compression or expansion of air is compression or expansion withoutjoss-or gain of heat by 1 6 COMPRESSED AIR. the air. This expression " without loss or gain of heat," it will be noticed, does not mean maintaining a constant tem- perature, but precisely the reverse of that. If during compression the air could be kept at a con- stant temperature by the abstraction of the heat as fast as it was generated, the air would then be said to be com- pressed isothermally. In isothermal compression or ex- pansion the air remains at a constant temperature through- out the operation. The rate of increase in the temperature of air during compression is never uniform. The temperature rises faster during the earlier stages of the compression than when the higher pressures are reached. Thus in compressing from i atmosphere to 2 atmospheres the increase of temperature will be greater than in compressing from 2 to 3 atmospheres, and so on. The rate of increase of temperature also varies with the initial temperature. The higher the initial tem- perature the greater will be the rate of increase at any point and throughout the compression. Attention is called to the diagram which appears as a frontispiece to this work. It is taken from " Compressed- Air Production," by W. L. Saunders, C.E. The writer herepf is in the habit of keeping this diagram in sight, and finds it suggestive and handy in the off-hand solution of many questions that arise. It would seem to be worthy of a rather fuller explanation than Mr. Saunders has favored us with. The diagram in fact comprises two distinct dia- grams, the one showing the temperature of the air, and the other showing the volume of the air at different stages of compression. If the diagrams are understood, there is no danger of confusing the one with the other, and as many of the lines do service for both diagrams, we are able to get DEFINITIONS AND GENERAL INFORMATION. I/ much from a small space. Compression is supposed to commence at the left of the diagram with any given volume of air at atmospheric pressure. As the compression pro- ceeds the successive stages of pressure are indicated by the series of vertical lines. Beginning at the extreme left witn the gauge pressure at zero, o, as shown at the bottom of the diagram, or with an absolute pressure of i atmosphere, as indicated at the top of the diagram, when the first vertical line is reached the air is then compressed to 2 atmospheres, as shown by the figure at the top, or to 14.7 Ibs. gauge pressure, as shown by the figures at the bottom. When the next vertical line is reached, the air has been compressed to 3 atmospheres, absolute, or to 29.4 Ibs. gauge pressure, and so on, the diagram extending to 21 atmospheres, or 294 Ibs. gauge pressure at the extreme right. In connection with the compression of air the important facts to be known are the temperature of the air when any given pressure is reached, and also the relative volume of the air when compressed to any given pressure, and these points it is the function of the diagram to show. The curved lines running from the lower left-hand corner A of the diagram are the lines of temperature, and they indicate by their height above the base-line AB the temperature of the air at any stage of the compression. It is assumed in the use of this part of the diagram that the air is com- pressed adiabatically, or that it loses none of the heat of compression during the operation. The several horizontal lines of the diagram serve to indicate by their height above the base-line AB the temperature attained. The space between any two adjacent horizontal lines represents 100 of temperature. Thus the temperature at the base-line 1 8 COMPRESSED AIR. AB being zero the temperature at the first line above it is 100, and so on. The temperatures indicated by the lines are shown by the figures at the left of the diagram along the vertical starting-line AC. Intermediate tempera- tures falling between the lines may be estimated by the relative distances from the lines. The temperature of the air at any stage of the compression depends upon its initial temperature. The higher the initial temperature is the higher will be the temperature throughout the compression. The diagram gives temperature-lines for the compression of air from the several initial temperatures of o, 60, and 100. These lines show, as noted above, that the higher the initial temperature the more rapid is the rise through- out the compression. Thus comparing the compression- line from o with the line of compression from 100 we notice that when the air has been compressed from i atmosphere to 10 atmospheres the original difference of 100 degrees has become 200 degrees, and when the com- pression is carried to 20 atmospheres, the difference has become 250 degrees. The curved lines starting downward from the point C at the upper left-hand corner of the diagram represent the volume of any unit of air after compression to any given pressure. The upper curved line represents the resulting volume after compression without any cooling of the air during compression, or with all the heat of compression remaining in the air. This is the adiabatic compression- line. The lower or inner of the two curved lines repre- sents the volume of air after compression to any given pressure, and with all the heat of compression abstracted immediately as it is developed, or with the air constant at the initial temperature throughout the compression. This DEFINITIONS AND GENERAL INFORMATION. 19 is the line of isothermal compression. The initial tem- perature of the air whether it is compressed isothermally or adiabatically is not a factor in determining the resulting volume. The total height of the starting-line A C represent- ing i volume of air, the volume at any stage of the com- pression is represented by the vertical height of either curved line at that point. The several horizontal lir^es- of the diagram serve to indicate the height, and by the height the volume, of the air at any pressure, and in this relation the lines have an entirely different function from that borne by them in relation to the lines of temperature. The initial volume is assumed to be divided into ten equal parts, and the space between any two adjacent horizontal lines represents one tenth of the original volume. Thus the first horizontal line below the top line CD represents nine tenths of the initial volume, the next line below in- dicates eight tenths of the original volume, and so on. These values are indicated by figures at the right of the diagram along the line DB. 20 COMPRESSED AIR. TABLE II. TABLE OF VOLUMES, MEAN PRESSURES, TEMPERATURES, ETC., IN THE OPERATION OF AIR-COMPRESSION FROM I ATMOSPHERE AND 60 FAHR. I 2 3 4 5 6 7 8 9 10 n t en O . rt & v.0. o G to G art ^C |J |i V S , the pressure of the air in the cylinder would have fallen to the original pressure of i atmosphere, and the piston at D would be balanced between the pressures above and below it. As the air is heated in the operation of compression, so is it correspondingly cooled during its expansion, and when the piston reaches D the air in the cylinder is then at atmospheric pressure, because it is then much colder than it was at the 30 COMPRESSED AIR beginning ; and it is solely because of this loss of heat that the pressure falls so early, and that the piston does not re- turn to A where it started from. If while the piston is at D the air can by any means recover all the heat which it has lost, the piston will return to A as before. The dis- tance DA compared with CA, or the distance DC, repre- sents the total possible theoretical loss of power in the com- pression and the re-expansion of air. At the risk of anticipating a number of points that I hope to bring out more fully and in detail later on, we may now refer to the more or less practical diagram Fig. 2. This diagram, scale 40, is intended to show the practical possibilities in the use of compressed air at 75 Ibs. gauge, or 6 atmospheres. The line ab is the adiabatic compression- line, or the line of compression, upon the assumption that no heat is taken away from or is lost by the air during the compression. The initial temperature of the air being 60 degrees, the final temperature would be about 415 degrees, and the final volume would be .28 of the original volume. The line ac is the isothermal compression-line, which as- sumes that all the heat of compression is got rid of just when it is produced, or that the air throughout the com- pression remains constantly at its initial temperature. The final volume in this case is .1666 of the original volume. Remembering that these lines, ab and ac, represent the compression of the same initial volume of air, it is evident that there is quite a difference in the amount of power em- ployed in the two cases, and herein lies the loss, or the pos- sibility of loss, of power in the operation of compression. The mean effective pressure or resistance of the air for the stroke upon the adiabatic line abl is 35.36 Ibs., while the mean effective pressure for the isothermal compression-line THE COMPRESSED-AIR PROBLEM. acl is but 27 Ibs., or only 76 per cent of the former. The comparison should, however, be reversed. The adiabatic 4 1 mean effective pressure is 131 per cent of the isothermal mean effective pressure : 27 : 35.36 : : i : 1.31, and this 31 per cent is, of course, the additional, or, as we might say, the unnecessary, power employed, assuming iso- 3 2 COMPRESSED AIR. thermal compression to be attainable. Neither of these compression-lines, ab or ac, is possible in practice. Air cannot be compressed without losing some of its heat dur- ing compression, so that the actual compression-line must always fall within or below the line ab. On the other hand, it is equally impossible to abstract all the heat from the air coincidently with the appearance of that heat, so that the actual compression-line must always fall outside or above the line ac. The best air-compressor practice of to-day is very near the line ao, or the mean of the adiabatic and the isothermal curves. The actual line is generally above this, and seldom below it. It would be impossible to produce a line exactly coincident with this in practice. If we produced a line giving the same mean effective pressure as ao, it would probably run above ao for the first half of the stroke, and perhaps a little below it at the last. If the com- pression were two-stage or compound, that is, if it were done in two or more cylinders instead of in one, there would of course be breaks in the continuity of the com- pression-curve. The mean effective pressure for the line aol is about 31.5 Ibs., or still nearly 17 per cent in excess of the M.E.P. for the line acl. As aol represents exceptionally good practice, the loss of power for the average practice in air-compression, independently of the friction of the ma- chinery, may be put at 20 per cent. Lest some impatient ones should drop the subject here, or lest some rival of compressed air should pick up this and run away with it, we might insert a reminder here that all this loss is not necessarily final. In all these comparisons for efficiency the actual compression-line is always to be compared with the isothermal line acl, because that is the ideal line for compression without loss of power, and because the termi- THE COMPRESSED-AIR PROBLEM. 33 nal volume cl is the volume actually available for use, no matter how economically or wastefully the air may have been compressed. Though at the completion of the com- pression stroke there is always some of the heat of com- pression remaining in the air, and its volume is always greater than cl y that heat is always lost in the transmission of the air, or in its storage, and the available volume is never practically above cl. After the cooling and contraction of the compressed air comes the question of .loss in the transmission of it. To cause the air to flow through the pipe there must be some excess of pressure at the first end of it, a constant decrease of pressure as the air advances, and consequently a loss of available power at the delivery end. But this loss has been greatly exaggerated. Here, as in other matters, the air-com- pressor builders have unwittingly, we will say done more harm than good as regards the interests of compressed air. Formidable tables are in all the air-compressor catalogues, showing the loss of pressure due to the friction of air in pipes. The tables are not dangerous, and are not published primarily for the purpose of frightening timid investors. They are only intended to suggest the size of pipe most suitable for any given case of transmission. If they tell us truly of the loss of pressure, they still fail to tell us that the loss of pressure is not necessarily, or to the same extent, a loss of power. The actual truth is that there is very little loss of power through the transmission of compressed air in suitable pipes to a reasonable distance, and the reasonable distance is not a short one. With pipes of proper size, and in good condition, air may be transmitted, say, ten miles, with a loss of pressure of less than i Ib. per mile. If the air were at 80 Ibs. gauge, or 95 Ibs. absolute, upon entering 34 COMPRESSED AIR. the pipe, and 70 Ibs. gauge, or 85 Ibs. absolute, at the other end, there would be a loss of a little more than 10 per cent in absolute pressure, but at the same time there would be an increase of volume of 1 1 per cent to compensate for the loss of pressure, and the loss of available power would be less than 3 per cent. With higher pressures still more fa- vorable results could be shown. Having compressed the air and conveyed it to the point where we wish to use it, we may turn again to Fig. 2, and see what we will be able to do with the air. The air may be used in various ways with widely different economic results, and little ingenuity is required to accomplish enor- mous losses. Having the volume cl, and using it in a cyl- inder of suitable capacity, cutting off so as to expand down to i atmosphere before release, the adiabatic expansion- line, or the lowest line that the air could make, would be the line cd t and the total loss in the use of the air, as com- pared with the power cost of compressing it, would be the difference between the areas aolh and Icdh, the latter being 66 per cent of the former. The temperature of the ak at c, where the expansion be- gins, being assumed to be 60, the cooling of the air which always accompanies its expansion will bring the tempera- ture far down the scale when d is reached, d being, of course, the end of the cylinder wherein the expansion takes place. The theoretical temperature of the air at the end of the stroke would be about 150. The actual tempera- ture in these cases is never found. as low as the theoretical temperature, because the air receives heat from the cylin- der and from the walls of the passages with which it comes in contact ; but it is usually still cold enough to cause seri- ous inconvenience in practice, and this cooling of the air THE COMPRESSED-AIR PROBLEM. 35 may in many cases be fatal to its employment, entirely re- gardless of the economy of the case. The air almost inva- riably contains moisture, the amount varying with the sur- rounding meteorological conditions, and as the air becomes attenuated and so intensely cold the water is rapidly frozen in the passages, and soon chokes them up and stops the operation of the motor. The prevention or the circumven- tion of the freezing up of air apparatus is an additional complication of the compressed-air problem to be con- sidered later. The trouble from the freezing up naturally suggests the heating of the air before it is used. The heating or re- heating of the air, where it is practised, not only brings us out of our trouble about the freezing up, but it increases the volume of the air and its consequent available power at a very slight expense for the heating. If the volume of air cl, being now at 60, be passed through a suitable heater and its temperature raised to 300, its volume will then be //, instead of cl, or .2434 instead of .1666, an increase of volume of about 50 per cent. In practice, to insure a tem- perature of 300 in the cylinder at the beginning of the ex- pansion, it will be necessary to heat the air considerably above that temperature, say to 400, as the air loses its heat very rapidly. If now we use this reheated air, the volume cl then becoming it, and expanding this air down to e, sup- posing the temperature at / to be 300, the theoretical final temperature will be about zero. The actual temperature, it is pretty certain, will not be below the freezing-point, and all our trouble about the freezing of the passages will have disappeared, and the power realized will have been much increased. It seems to be quite practicable, by ef- fective cooling of the air during its compression, and by 36 COMPRESSED AIR. reheating it before its re-expansion, to bring the expansion- line ie to enclose an area not less than that enclosed by the compression-line ao, and then the entire losses will be those attributable to the clearances and to friction. It is said that in practice 85 per cent of the initial power has already been realized after transmitting the air to considerable dis- tances. " It is said " accomplishes many wonderful feats. It was remarked above that the air after compression and transmission might be employed with widely different economic results. As an instance of "how not to do it " I might cite the case, of too frequent occurrence, where air is delivered to a mine for operating rock drills and other mining machinery, and air then taken from the same pipe- line for operating a pump. This practice would be all right if the pump were adapted to the work to be done and to the pressure of air carried. The pump, however, is gen- erally a common direct-acting steam-pump, with all that the term implies, and which has been obtained without any reference to the economical use of the air. As it has prob- ably already been run by steam, or is designed to be run by steam, it calls for a low operating pressure ; this being a necessity on account of the condensation and loss of pressure in steam when transmitted through long pipes. Say that the compressed-air pipe carries 75 Ibs. pressure, while the pump only requires 25 Ibs. It would be an ad- vantage in a case like this to use a pressure-reducer in the supply-pipe at a considerable distance from the pump, so that the expansion to the lower pressure required might take place, and the air have an opportunity to recover its temperature and volume before going into the pump. This, however, is seldom attended to, and the required reduction of pressure is effected entirely by the throttle- valve at the instant of admission. The available power, T'HE COMPRESSED-AIR PROBLEM. 37 then, when the air is so employed, will be represented by the area pmnh as compared with the area ablh, or, at the best, aolh, representing the power that was expended in compressing the air. Then, if we deduct the losses attributable to the useless filling of the large clearances of the common steam-pump, and to the leakages that are the usual accompaniment of such generally extravagant prac- tices, it is little wonder that compressed air is held in low esteem. Under circumstances far from the most unfavor- able I have found pumps realizing only 15 per cent of the power expended at the compressor, and I have no doubt that there are many pumps being operated, or whose oper- ation is attempted, where not more than 10 per cent of the original power is realized ; and, even then, when the use of compressed air for operating such pumps under such con- ditions is condemned, it is apt to be because they freeze up and won't go, rather than on account of their enormous waste of power. From the fact that a mining pump has a lift that is nearly constant, the pump, if properly propor- tioned and adapted to its work, should be an efficient mis- sionary for compressed air, rather than its most malignant traducer. The word " loss " that we find ourselves using in connec- tion with this general subject should not be allowed to mislead us. The use of compressed air is for the accom- plishment of a desirable purpose, and it is not to be ex- pected that such a purpose can be effected for nothing. The transmission of power is as much to be paid for as the generation of the power. Where water power is used, the means of transmission may be the principal item of cost. Where the difference between the power expended and the power realized is not excessive, that difference is simply a fair price paid for a good service rendered, and there is no COMPRESSED AIR. loss about it. Where losses do occur in the use of com- pressed air, they are like the losses which occur in business, and which cut short many a brilliant career. Power is lost simply because it is not saved, and the means of saving are not hard to find nor far to seek. The excessive losses are not necessary nor unavoidable, nor without compensation. A failure to understand and appreciate this situation im- pedes the progress of compressed air. TABLE III. TABLE OF FINAL TEMPERATURES OF AIR COMPRESSED ADIABATICALLY TO DIFFERENT GAUGE PRESSURES FROM AN INITIAL PRESSURE OF I ATMOSPHERE, AND FROM DIFFERENT INITIAL TEMPERATURES. Final Pressure Gauge. Initial Temp. 0. Initial Temp. 32. Initial Temp. 60. Initial Temp. 100. I 8 41 70 Ill 2 16 50 79 121 3 25 59 88 132 4 33 67 97 140 5 4i 75 106 150 10 74 H3 144 191 15 104 144 177 226 20 130 171 207 2 5 8 25 153 196 233 28 7 30 175 219 258 313 35 195 240 280 337 40 213 260 301 360 45 231 279 321 38i 50 247 296 339 401 55 262 316 357 420 60 277 328 373 437 65 291 343 389 454 70 304 358 404 471 75 317 37i 419 486 80 330 384 433 SOT 85 342 397 446 5i6 90 353 410 459 530 95 3 6 4 422 472 543 IOO 375 435 484 556 125 425 486 540 617 150 468 532 588 669 i?5 507 574 633 717 200 542 612 672 781 CHAPTER V. THE INDICATOR ON THE AIR-COMPRESSOR. READING AND COMPUTING THE DIAGRAM. THE recent advances that have been made in steam- engine economy are not fully and generally realized. The engines of the Great Eastern steamship of forty years ago, representing the best engineering practice of her day, de- veloped 8000 horse-power. The engines of the Campania to-day show 30,000 horse-power upon practically the same consumption of coal. The gain is attributable to the adoption of the multiple expansion-engine, to the reheating between the steps, and to the general prevention of con- densation ; but the promoter and adviser all along the way through the successive stages of improvement has been the indicator. The indicator is to-day the companion and the trusted monitor of the steam-engine designer and builder as well as of the engineer. He would be a strange competitor for steam-engine trade in these days who would not freely and gladly show the cards from his engine, and it goes without saying that he would be an unsuccessful one. The air-compressor business is still an " infant industry," although a growing one. No better evidence is needed of the juvenility of the air-compressor trade of to-day than the difficulty of obtaining cards from most of the 39 4O COMPRESSED AIR. " standard " compressors. And yet the services of the indicator may be as valuable to the air-compressor and the air-engine as to the steam-engine, and they are certainly fully as applicable. All circumstances seem peculiarly to invite the applica- tion of the indicator to the air-compressor, and to the study of air-compression practice and results by its aid. In fact, the air-compressor seems to be the ideal and only perfect field for the indicator. So far as I know, a steam-actuated air-compressor is the only machine where an indicator can be applied and be made to tell the whole story of the power developed and of the work done. In the steam- pump the report of the card of the water-cylinder is af- fected by questions relating to the inertia of the body of water. With a steam-engine of any type there is always some uncertainty about the friction of the working parts of the engine. We can take what we are pleased to call the " friction diagram," when the engine is running without doing any external work, and we know what resistance the steam has to overcome at that time ; but that tells us com- paratively little of the resistance of the engine parts when loaded. We know that the friction of nearly every work- ing part of the engine increases with the load, but when the load is on, we do not know from the indicator-card how much of its mean effective indicates actual work done or how much of it belongs to the friction of the engine, and to get the result with any certainty and accuracy it is nec- essary to employ some form of dynamometer in connection with the indicator, and let them fight it out between them. In the case of the air-compressor this is all different. The air-compressor is its own dynamometer. By taking cards from both the air- and the steam-cylinders at the same THE INDICATOR ON THE AIR-COMPRESSOR. 4! time, or when the compressor is running under the same conditions, we get a perfect statement of the power de- veloped and of the actual work done, and then we know too that the difference in indicated horse-power between the air- and the steam-cards clearly shows the power that has been expended merely to keep the machine in motion. The cards not only give "the comparative total power and work, but also the relations of the one to the other at any point of the stroke, showing the air resistance at any point, as well as the force of the steam at the same point, and through this knowledge it will advise us whether the air is compressed with economy or whether better results are to be sought for. Realizing the importance of the indicator as an indis- pensable aid in the full development of economical air- compression, it is proper that we learn what we can of the peculiarities of the air-card and of the means of manipulat- ing and interpreting it. We can only consider at first the card from the single air-cylinder, in which the whole opera- tion of air-compression is completed at a single stroke. The cards from cylinders in which either stage of a com- pound compression is carried on assume peculiar shapes, which we may find pleasure in studying later on. To an indicator-man who has been brought up, as most have, exclusively upon steam-cards the air-card is at first a little confusing, from the fact that all the operations upon the one card are the reverse of those upon the other. The admission-line of the steam-card is the delivery-line of the air-card ; the expansion-line in the one is the compression- line in the other ; the exhaust or back-pressure line is the admission-line, and the compression-line becomes the re- expansion-line. One can, however, soon " catch on " and 4 2 COMPRESSED AIR. become familiar with each operation and its representative part of the diagram. It is not the purpose of this work to instruct in the ap- plication and use of the indicator. We must assume that the indicator is in competent hands, or its evidence will be worthless. Indicator-cards have, however, a way of telling for themselves frequently if they have not been taken with a reasonable regard for the essential conditions. As the peculiarly important part of the air-card is the compression- line, it is necessary that the drum movement be correct, and that, in proportion to its length, the travel of the card shall be accurately coincident with the piston travel at all points. Cards, to be relied upon, should not be taken until the com- pressor has been run long enough to have attained its com- plete working conditions. We know that the compression of air heats it, and that the heat then in the air is commu- nicated more or less to everything in contact with it. When the cylinder becomes heated, it has its effect back again upon the air, and until the compressor has been run continuously and at full pressure for an hour or so, the full temperature of the working parts has hardly been reached and the effect of the heated parts upon the temperature of the air at different points of the stroke will not be correctly indicated. Cards aken from a compressor that has only just been started will give a lower compression-line and a lower mean effective pressure (M.E.P.) than those taken after the cylinder and piston and connecting parts have been heated up to their mean working temperature. Fig. 3 is offered as an ideal and typical single-compres- sion air-cylinder card, designed to show the points and properties of the card, and the methods of manipulating and studying it. The card is somewhat smoother and cleaner and in most respects more perfect than any actual THE INDICATOR ON THE AIR-COMPRESSOR. 43 card, except that the admission-line is purposely drawn rather low to keep it perfectly distinct from the atmosphere- line. The lines constituting the actual diagram are as follows : AB, Compression-line BC, Delivery CD, Re-expansion " Z>A, Admission 44 COMPRESSED AIR. These constitute the actual card, and together represent the complete cycle of operations occurring in one end of the air-cylinder for one complete revolution of the com- pressor-crank. The atmosphere-line, MN, is also traced by the indicator, and is the neutral line of the diagram, or the line of departure in air-compression. For the proper interpretation of the diagram additional lines are to be drawn as follows : EF, the line of perfect vacuum. This line is drawn parallel to the atmosphere- line, MNj and at a distance below it determined by the scale of the diagram. The pressure of the atmosphere at sea-level being 14.7, and always decreasing as the altitude increases, the practice of calling the atmospheric pressure 15 Ibs. may be said to be a rather loose one. If the com- pressor is operated at a considerable altitude above the sea-level, as many are, the atmospheric pressure at the time and place where the diagram is taken should be ascer tained by a barometer, and the line EF be drawn accord- ingly. It should be remembered, as we will see when we get to it, that a height of only a quarter of a mile, or a little over 1300 feet, will make a difference of 7 per cent in the volume of air furnished. The vertical lines PA and CL having been drawn per- pendicular to MN) and defining the extreme length of the actual diagram, the clearance-line GH may next be drawn. This is drawn parallel to CL, and the distance CG or LH may be ascertained by computation. The volume repre- sented by the rectangle APCL is the actual displacement of the piston for its whole travel. The volume of air acted upon by the piston is this volume increased by the volume CGHL remaining in the clearance-space of the cylinder. This volume of air, CGHL, at the end of the compression- stroke, and at the pressure indicated by the diagram, has upon THE INDICATOR ON THE AIR-COMPRESSOR. 45 the return stroke of the piston re-expanded until it reached the atmospheric pressure again at D. This re-expansion is so quickly accomplished that whatever the temperature at the beginning the re-expansion is practically adiabatic. The relative volume before and after the re-expansion may be found in column 5 of Table *t*iM Assuming the scale of the diagram to be 30 and the pressure at CG to be 70 Ibs. gauge, and designating LH by x we have the proportion x : DL -f x : : .288 : i Then the length DL being .25", we have x : .25 -f- x : : .288 : i ; then x = .072 + .288^, and .712.3: = .072, x = .101. So that CG or LH equals say -^ ", and GH may be drawn accordingly. Having drawn GH, the rectangle APGH represents the total volume of air subjected to compression for the stroke, and noting the point a, at which the compression-line be- gins to rise from the atmosphere-line, and drawing the perpendicular ae, then aeGH represents the total volume of air at atmospheric pressure. The point a, being the point at which compression from atmospheric pressure begins, may be considered the beginning of the whole diagram, and the cycle of operations for the entire stroke may be considered to start from this point. For computing the mean effective resistance the entire enclosed area of the actual diagram ABCD is to be taken, 4-6 COMPRESSED AIR. and this area may be measured by the planimeter, or by the mean of a series of ordinates in the customary way, as with any other diagram. The area lying below the atmosphere- line of course represents the resistance upon the return stroke, but the diagrams from both ends of the cylinder being assumed to be similar, the entire area may be taken for the single stroke. The correct practice is to take dia- grams from both ends of the cylinder, and it should be followed if possible, but it is clearer and simpler for us here to consider only the single diagram. The M.E.P. of the diagram having been ascertained, the indicated horse-power (I.H.-P.) represented may be com- puted precisely as in the case of a steam-engine. Thus the M.E.P. in the diagram before us happening to be 30, if it were taken from a cylinder 20" dia. X 24" stroke at 80 revolutions per minute, the I.H.-P. for the double stroke will be as follows f : 2o 8 X .7854 X 30 X 4 X 80 -T- 33,000. I like always in such cases to put it down in this way, that I may be sure that I get in all the ingredients. It is not necessary to run for a table of squares or of areas, and no time is saved by doing so. The decimal .7854 is always cleanly divisible by the constant divisor 33,000, giving us .0000238. It is not difficult to remember this or to keep it posted with other labor-saving devices in a convenient place. The ciphers in the other factors will help us to elbow the decimal point to the right, and our case will then stand like this, a little string of simple and easy multiplications : 2 2 X .238 X 3 X 4 X 8 = .238 X 384 = 91-39 I.H.-P. We will not here go into the question of the additions to be made to this for friction, etc. THE INDICATOR ON THE AIR-COMPRESSOR. 47 The I.H.-P. having been ascertained, that gives us the power consumed, or the cost of the compression, and then we naturally want to know as soon as possible the actual quantity of air compressed and delivered, or how much we have got for our money. The indicator-diagram shows this very accurately. At the point a, where the compres- sion-line takes its departure from the atmosphere-line, the cylinder is shown to be full of air at the atmospheric press- ure and corresponding density. This is not the whole cylinder, as a portion of it, Aa, has been already traversed by the piston. Whatever proportional distance the point a may be from the beginning of the stroke is to be deducted from the total length of the stroke and the remainder repre- sents the total actual volume of air at atmospheric pressure subjected to compression for that stroke. The compres- sion and delivery of the air goes on with the advance of the piston until it reaches the extreme end of its stroke at CL, but when that is reached, the clearance-space LCGH is filled with air compressed, but not delivered, and upon the return of the piston this air re-expands until it reaches the atmosphere-line at 0, so that practically the travel of the piston from o to L and back again has accomplished nothing toward compression, and the distance oL is also to be deducted from the total length of the line AL y when that line is taken to represent the volume of air compressed and delivered. In the diagram before us if AL be 3^ " and ao be 3 T y, the ratio of air compressed and delivered is -^ = 88 per cent of the cylinder capacity. As was re- marked, this diagram does not represent actual practice, and the ratio is not usually as low as this, being more fre- quently found hovering about 5 per cent in the best com- pressors, and rarely below that. 4<> COMPRESSED AIR. So far as the indicator has anything to say about the economy of the air-compression, and it has much to say, its evidence is found chiefly in the compression-line of the diagram, and for comparison it is necessary to describe upon the diagram the theoretical isothermal and adiabatic curves. To facilitate the drawing of these lines the dia- grams Figs. 4 and 5 have been provided. The dimensions of the book have made it necessary to engrave these at one half of the full size. They can readily be reproduced in full size by any draughtsman, and will be found useful for the purpose for which they were designed. As they stand here they are correct for scales that are double those indi- THE INDICATOR ON THE AIR-COMPRESSOR. 49 cated. Thus the 15 ordinate is correct to apply to a 30- scale diagram, the 20 ordinate for a 4o-scale diagram, etc. The compression-line of the air-card is more easily studied than the expansion-line of the steam-card, as it always has a definite beginning or point of departure at a, such as the Adidbatic Compression Fig. 5 steam-card never has. From this point a the isothermal and the adiabatic curves are to be drawn. When the compressing piston is at ae, the air under compression includes the con- tents of the clearance-space at the farther end of the cylinder, and the total body of air under compression is represented by the rectangle aeGH. Vertical lines then 50 COMPRESSED AIR. are to be drawn dividing this space into 20 equal sections, and for convenience the lines are to be numbered, begin- ning at the line next to ae, 19, 18, 17, 16, etc. It will not be necessary to number the last two or three lines to the right, or even to draw them, as the curves will not reach them. It will be noticed that the numbering does not include the boundary-lines ae and GH. Referring now to the diagram Fig. 5, for drawing the adiabatic curve, AB is the atmosphere-line and CD is the line of perfect vacuum, or the zero line of absolute pressure. Taking from the diagram, Fig. 5, the ordinate line correspond- ing to the scale of the indicator-card, the distance between AB and CD, measured upon this line, is the distance be- tween the atmosphere-line and the line of perfect vacuum, and the vacuum-line may be drawn upon the card accord- ingly parallel to the atmosphere-line and at this distance from it. Then upon the same vertical line of the diagram Fig. 5 the distance from AB to the first intersecting line above it indicates the distance to be laid off upon the ver- tical line No. 19 of the card as one point of the required adiabatic curve. The distance from AB to the second line above is the distance to be laid off upon the vertical line No. 18 as another point of the required curve, and so on : the points may be successively laid off upon the vertical lines of the card until the delivery-line BC is reached, or a little above it, when it is unnecessary to go further, and the required curve may be drawn coincident with the points that have been thus located. The isothermal curve may be drawn in the same way by the aid of Fig. 4. The points upon the first two or three vertical lines to the left may be so close to the actual compression-line of the cardpor so nearly coinci- dent with it, that it is more confusing than helpful to draw the lines, and they may begin at a point further along the line. THE INDICATOR ON THE AIR-COMPRESSOR. 51 This diagram, Fig. 5, assumes the atmospheric pressure to be 14.7 Ibs., and is only applicable for approximately that pressure. If the atmospheric pressure for the altitude at which the compressor works, and where the indicator-card was taken, is decidedly less than 14.7, the atmosphere-line drawn by the indicator will represent that pressure and will not represent 14.7 Ibs. The mean effective pressure can of course be computed by taking the area of the indicator- card as it stands; but if it is desired to draw the adiabatic and isothermal curves by the aid of our diagrams, Figs. 4 and 5, it will be necessary to first draw a horizontal line representing the atmospheric pressure of 14.7 Ibs. To do this first draw the zero line at a distance below the existing atmosphere-line corresponding with the ascertained atmo- spheric pressure and the scale of the diagram. Column i or 2 in connection with column 4 of Table IV., given at the end of this chapter, will generally furnish the data necessary for this service. The zero line having been drawn the sea-level atmosphere-line may then be drawn 14.7 Ibs. above according to the indicator-scale. When this line is drawn the point where the compression-curve crosses it may be noted and also the point where the reexpan- sion line strikes it, and ignoring the original atmosphere- line drawn by the indicator, the adiabatic and the isother- mal curves may be drawn precisely as previously discribed. These adiabatic and isothermal curves when described are rather an aid to the eye in making comparisons with the actual compression-line of the indicator-card than nec- essary in computation. The mean effective of the card is ascertained by the planimeter or by measurement, and the mean effective for adiabatic and isothermal compression un- der the same conditions may be found in Table II, and the economy of the actual compression may be learned by com- COMPRESSED AIR. parison with them. This paragraph is only meant to apply to approximately sea-level computations. Table IV will be found convenient in computations upon air-compression at various heights above the sea-level. Column 7 gives the values of the volumes of air actually compressed at any given height as compared with equal volumes of free air at sea-level. TABLE IV. TABLE OF ABSOLUTE PRESSURES, BOILING-POINTS, ETC., AT DIFFERENT HEIGHTS ABOVE SEA-LEVEL. I 2 3 4 5 6 7 Weight Volume of Volume of Height above Sea-level, Bar- ometer, Inches of Boiling- point, Degrees Absolute Pressure, T hs Of I Cu. Ft. of Air at Air Equal to i Cu. Ft. of Free Free Air at Sea-level equal to iCu. Feet. Mercury. Fahr. JUDS. 60, Air at Ft. at given Lbs. Sea-level. Altitude. 30 212 14.7 .0765 I I 512 29.42 211 14.41 .07499 .02 .98039 1025 28.85 2IO 14.136 07356 .04 .96154 1539 28.29 209 13.86 .07213 .06 9434 2063 27-73 208 I3.587 .07071 .08 .9 2 59 2589 27.18 2O7 13.318 .0693 .IO .90909 3H5 26.64 206 13.054 .06793 .12 .89285 3642 26.11 205 12.794 .06658 .14 .87719 4169 25-59 204 12-539 .06525 17 .8547 4697 25.08 203 12.289 06395 .19 .8403 5225 24.58 202 12.044 .06267 .22 .8197 5764 24.08 2OI 11.799 .0614 .24 .8064 6304 23-59 2OO U.559 .06015 .27 .7874 6843 23.11 199 11.324 05893 .29 7752 738l 22.64 198 11.094 05773 32 75757 7932 22.17 197 10.863 0565 35 . 74074 8481 21.71 196 10.638 .05536 .38 .7246 9031 21.26 195 10.417 .05421 .41 .7092 9579 20.82 194 10.202 .05309 44 .6944 10127 20.39 193 9-99 .05199 47 .6802 10685 19.96 192 9.78 .0509 50 .6666 11243 19-54 I 9 I 9-57 .0.198 53 6536 11799 19-13 I9O 9-37 .0488 56 . 64 i 02 12367 18.72 189 9.17 .0477 .60 .625 12934 18.32 188 8.98 .0467 63 6135 J3498 17.93 187 8.78 0457 .67 .6 M075 17-54 186 8-59 .0447 .71 .5848 14649 17.16 185 8.41 0437 74 5747 CHAPTER VI. THE BEGINNING OF ECONOMICAL AIR-COMPRESSION. WHILE it may easily appear that the purpose for which compressed air is used in any given case, or the conditions under which it is applied, make the question of power economy a distinctly subordinate one, and often relatively a very little and unimportant one, still it remains that for whatever purpose we use the air the cheaper we get it the better it is for us, and considerations of economy in the compression of it are always in order, and whatever saving is effected there is necessarily a clear gain. If we are to go into the compressed-air business " for all there is in it," the way to do it successfully and profitably is first of all to control the whole business. By this is not meant the establishment of a monopoly whereby we might have the compressing of all the air that is used, although there might be great profit in that. But with what air we do handle we cannot expect to accomplish much in the way of economy, unless we have as full control as possible of the air through each of the operations involved in its use : the compression of the air, its transmission to the place or to the apparatus where it is to be used, and its actual employment for the purpose intended. There are losses possible at several points, or at all points, along the series of operations, and there are commensurate savings to 53 54 COMPRESSED AIR. be effected by the avoidance of those losses. The losses may be defeated and the savings accomplished rather by a concentrated than by a divided control and accountability. Economy in air-compression should begin at the begin- ning, and at the beginning we first have to do with the " free air," or air at atmospheric pressure. This is our raw material, and it is of course desirable to get it as cheaply as possible. Now it so happens that in keeping our ac- counts of profit and loss in this business the raw material is measured out to us and charged against us not by weight, but by bulk, so that whatever air we want to use it is desirable to get it to the compressor in as small a volume as possible. The smaller the relative volume of air at the beginning of the series of operations the greater will be the profit at the end for any given service realized. The vol- ume of free air increases or diminishes as its temperature rises or falls, which means that we should get our free air as cold as possible. The colder the air is the less it will measure in cubic feet, and we may consequently say that the colder it is the cheaper we are getting it. It seems necessary in all of the operations with com- pressed air to keep the accounts of profit and loss, and the record of work done, by the volume of free air that is handled. This involves fewer uncertainties than if we were to base our computations upon the volume of air after compression to any given pressure, or at any later stage in its transmission or use. The air-compressor, when the necessary corrections for clearance, etc., have been deter- mined, is a very reliable air-meter, and from it may be ob- tained a very close record of the free air taken in by it and compressed and delivered. After the beginning of opera- tions the temperature of the air is such an uncertain and BEGINNING OF ECONOMICAL AIR-COMPRESSION. 55 variable factor, and is still of such importance in the result, that all calculations are upset by it. The absolute meas- ure of the air operated upon would of course be its weight, but this it is not possible to ascertain in extensive practical operations. The volume of air at common temperatures varies di- rectly as the absolute temperature. With our air-supply at 60 its absolute temperature is 521, and the volume of it will increase or decrease ^| T for each degree of rise or fall of temperature. In securing our supply of free air for the compressor, then, if we can get a difference in our favor of 5 by laying a pipe and leading the air in from the outside of the compressor-room, or from the shady side of the building, or from the coolest place near by, instead of using the air in the compressor-room, we accomplish a sav- ing of about i per cent. If we secure a difference 'of temperature of 10, which in practice is frequently quite possible, we save 2 per cent absolutely without cost, ex- cept the first cost of the pipe or box to lead the air in. I know that the average machinist or engineer, or the man who calls himself distinctively the practical man, cannot commonly appreciate these small figures, or have any re- spect for such small savings, but when it comes to business I do not know why they should not have the same weight as the same values have in any other of the details of busi- ness. Brokers have to live and flourish upon commissions of ^ or y 1 ^- of i per cent, but " practical " men are so wealthy that i or 2 per cent is not worth considering. The pipe to convey the cool, free air from the point where we determine to take it to the compressor may as well be of wood or of cement or earthenware as of iron, and in fact such material for its non- conductivity is to be 5 6 COMPRESSED AIR, preferred. The pipe should of course be large enough to convey the required flow of air with perfect freedom. Some of the best air-compressors of the day may be con- nected quite readily with an outside air-supply, and they make provision for it ; others cannot easily be so con- nected, which is unfortunate for them. Another point that has not hitherto received the atten- tion that it deserves, although much more important than the preceding, is the necessity, in the interest of the best power economy, of not only getting the air as cold as pos- sible at the compressor, but of getting it as cold as possible into the compressor. We have too readily assumed that the one covers the other, when, as a matter of fact, it never does. The temperature of the air at the cylinder and about to enter it does not guarantee the temperature of the air in the cylinder at the moment when the cylinder is filled and compression begins. It is not too much to say that the temperature of the air outside the cylinder and of that inside is never the same. Yet it is not to be forgotten that the sole object of the effort to get cool air for the compres- sor is to have it as cool as possible, and of as small a volume as possible, at the moment when compression begins. How cool the air may have been at any previoas moment, how- ever near, has nothing to do with the case. In another chapter I have remarked that the air-compres- sor is the ideal and the only perfect field for the use of the indicator, that it is the only place where the indicator dia- grams will tell the whole story both of the power expended and of the work accomplished. This is undoubtedly true, but it is a statement that is quite likely to be understood to say more than it does say. The indicator diagram from the air-cylinder does not tell all that it seems to tell, or it BEGINNING OF ECONOMICAL AIR-COMPRESSION. $? tells it wrong. You may note upon the diagram the point, very near the beginning of the compression-stroke, where the cylinder, if we may believe the diagram, is filled with free air, or air at atmospheric pressure, and from that, after deducting what fills the clearance-space at the end of the stroke, we may compute the volume of free air actually compressed and delivered ; and then, later, we may realize that we have not got the volume of free air that the dia- gram testifies to. This is due to the fact that the diagram has nothing to say about the actual temperature of the air, either at its admission, at its discharge, or at any point of the stroke. With steam, unless it is superheated, the press- ure indicated guarantees the temperature; with air the pressure and the temperature have no necessary connection. I may show you a diagram from an air-compressing cylin- der where the air-admission line is almost exactly coin- cident with the atmosphere line, and where the compression jine begins to rise above the atmosphere line immediately at the beginning of the compression-stroke, showing that the cylinder is completely filled with air at atmospheric pressure, and we may congratulate ourselves that the dia- gram is an excellent one in this respect ; but suppose that when the cylinder is just filled, and compression is just beginning, our cylinder is filled with air at 120 instead of at 60, which is the temperature of the supply. It means that our cylinder holds rather less than .9 of the air that we are assuming that it holds, and which the diagram says that it holds. It means not merely that the practical capa- city of the compressor is one-tenth less than we assume it to be, but that for the compression of this nine-tenths we are still expending the full power as represented by the steam-card. If the difference in indicated horse-power 58 COMPRESSED AIR. between the air-cylinder and the steam-cylinder is ten per cent of the air-cylinder, or if the power ratio of the steam to the air be i.i : i, it is not a bad showing. This is about the ratio obtained in the best air compressors of the day. But if this i.i, the power of the steam-cylinder, is to be compared not with i, the full capacity of the air-cylinder, but with .9, its actual contents, the case is quite different: .9 : i.i : : i : 1.22, which is a result not worth bragging about by any compressor builder. There seems to be no means of ascertaining the actual temperature of the air during the operation of compression. The temperature of the air at different points of the stroke would be easily computable from the indicator diagram, which shows the pressure attained at any point, if we only knew the initial temperature, but as we have no means of knowing the initial temperature we do not know the actual temperature at any time. Who will tell us how to find it out ? This does not seem to be an impossible problem. It looks at first sight almost as simple not quite as to tell how fast a stream of water flows through a pipe. But no- body has yet invented a satisfactory water-meter. In the meantime we can only use our mechanical judgment and common sense as to the best means of getting the air into the cylinder as cool as possible. We can say in a general way that the air should enter the cylinder by the shortest and most direct possible passage, and with as little contact as possible with any metal at a higher temperature than its own. Some interesting matter bearing upon the topic we are speaking of is found in a paper upon " Blowing Engines," by Mr. Julian Kennedy of Pittsburgh, read before the Mining Engineering Division of the World's Engineering Congress at Chicago. Mr. Kennedy says: BEGINNING OF ECONOMICAL AIR-COMPRESSION. $Q " This heating of the incoming air expands it, and pro- portionately reduces the weight of air entering the cylinder at each stroke. I have observed this in the ,case of an engine which was so constructed as to cause .the air to travel about 3 inches over the hot metal in thin films -f$" thick. Alongside of it was another engine of the same size and make, except that valves were used which allowed the air to pass over about i inch of metal, the openings being of such size that each stream of air was 2 inches in thick- ness. Careful and repeated tests of these engines, when both were in good order, showed that, while the indicator diagrams were practically the same, the one with the large valves would burn about roper cent more coke in the fur- naces, a result which could only be explained on the sup- position that, in the case of the engine with the small air openings, the incoming air, in passing through the small and tortuous passages in the heads, was heated about 25 C. more than in the case of the other engine." The above, it should be remembered, speaks only of blow- ing engines, where the air-pressures are low, and where the heat of compression and the heating of the parts in contact with the compressed air do not range high. In an air-com- pressor every part of the cylinder in contact with the air after compression naturally becomes much hotter than in the blowing-engines that Mr. Kennedy speaks of, and the heating of the inrushing air may also be much greater. The air remaining in the clearance space of the air-cylin- der at the end of the compression-stroke, being between the hot piston and the more or less heated cylinder head, may not have lost much of its heat of compression, but by the cooling action of the water-jacket it must have lost some of its heat, and its temperature cannot therefore be as high as the theoretical temperature due to the compression. 6 ON4k 00 M O ON4k ~ 01 O vj 4 tOOWVJ4k tO ONO W VJ M 4k OO N) ON 10 vj w O OO4k O 4* OO ONOl ON M Ol N OOW M OO ON4k H O ON4k tO * W 10 O O OCVJ Ol W 10 M O 00 O\0l W tO M O OOv) ONOl Ol 4k W tO M 10 10 W OOW - 4k to 01 M Ol oT^ 01*01 "to vf OO OOW OWO4^O4^O4k tO 4k ON 00 00 ONOl 4>- *. w 10 M to 00 vl vj vj ON ON ONOl OiOi4k4k4kWWWtOtOtOMMMMi-* M vj w M O Ol MVJW M O Ol O ONtO O 004k O OO ON4*- tO O OO ON4k tO to 4k O\ "-" VI tO OOW O 4k 00 M ONW 4k OO to ONW - O4kOWvJ4k"tloiO ONW O vj 4? M OOOl 10 w O04k O Ol ONOl 4k4kWtOMMOOOOO OOVJ ON ONOl 4k4kOJWtOt010MH Ot04kOONOOON>4kOONOOOt04kOONOOOON10 O04k O ON N> O04k u o ******3j[*j s n 9 JO OO "^q OCn * OJ tjJ tO H O O OO-vj >sj QNt/1 ^-**.OJOJ 00 H M 00 OOW 00 00^1 OxONwUlUlUl-^-^ OOOJ U) tOvj H OXM O\OCnOOl * flsswM^-iwwag^ffaOT^^^ Ol ff 5' V14*. to H Qvl*ylW OO OOOl W M OOVJ ON4k MOO OOVJ Ol 4k W tO H M vj w l-l OOW O 01 4k W OOOl (0 o vj Ol M OO ON4k M O NO VJ Ol W M M ON OO ON I W O 0\ W M vj 10 004k tOOONMVJW-OOlOOO ON4k 10 O OO ON4k 10 vj 01 4k W 10 O 00 ON4k W tO MOvjOl4kW HO OOVJ ONOl 4k OJ 10 M O OO 00 OOO 00 WIOMMMOOOOO OOVJ vl ONOl Ol4v4kWOJNIOIOi-lMM O4kVJ4v H4k OOi-iOi M OOtOOl OOtOOOlO IOO ONtOO ONW O ONW O 4k OOOl W vj tO ON M OOV/l O 4k O 4k M OOW VJ 4k to O ONW M OOOl 10 tO 4k VJ O OOVJ ON ON ONOl 4kWtOMMQOOO OOVJ ONOl 4.4kWWt3tOMH OOO O4kOOH M IOvlWW4k4k O OOl ONvJ 10 vj w OOW O04k O 4k OY M ONO 10 004k OOl OOrt ONIO OOMVJ001 4kVl OWOl OOM4-VJ to W H O O 00 ON'Ji W M O O 00 ONOl W 10 M OOVJ ONOl Ol 4k OJ 10 Ol 00W4k 004kVIO -4kVJ 04k0ivj Swoivj OOO WOl ONOO OWOl tO OOOW ON O04k O tOOl OOO ONIOOl OO4k O ONtOOOi MVIW W Or VJ VJ ON 'lO O vl It ^ O 'ON^ ^ ^ 00 ON'-O O ^O OOol W M O O vj ONOl W 10 M W vj M OOOl OOtO ONOvJ4^vJ HOiO ONW vj O vl 4*. *^ OOOl to O ONW ON4k tO OOVJ OX W 10 H 00 ON4k W W M O OOVJ ONOl 4k W 10 M vl OOO 8 Oi MOOi4k OONkOOvjOl HvjW O OOONtO OO ONOl W M O M Ol W M 4k ON 000 OWO!VJO-104kVJOMIOWON OOO O M W 4k Ol ONVJ OO O W ONVJ O tOOl OOO t04kv| OW ONVJ O 10 Ol ON OOO H to 4- Ol vj OO Ol 01 to 2 CHAPTER XII. COMPRESSED-AIR TRANSMISSION. THE accompanying table, VII, gives the actual volume of air passing through a pipe of given diameter when the linear velocity of flow is known. This is merely a convertible table of pipe capacity, and will be useful as such in deter- mining the size of pipe best adapted for a given service, and it has nothing to do with the conditions which may determine the rate of transmission. While in considering the operation of air-compression we base our computations upon the volume of free air com- pressed, it is better in questions relating to the transmission of the air to consider the actual volume of the air during the transmission, or usually either at the beginning or at the completion of the transmission. As air in transmission soon attains the temperature of the pipe and its surround- ings, its temperature need not generally be taken into ac- count as affecting the volume. The volume of free air transmitted may be assumed to be directly as the absolute pressure or the number of atmospheres to which the air is compressed. Thus if the air transmitted be at 75 Ibs., or 6 atmospheres, the actual volume of free air transmitted will be six times the volume given in the body of the table. For comparing cases of transmission the linear velocity of flow is generally adopted, and is the more convenient form of statement. It is generally considered that for econom- no COMPRESSED-AIR TRANSMISSION. Ill ical transmission the actual velocity in main pipes should not exceed 20 feet per second. It would be well if more attention were given to the capacities of the distributing- pipes employed. In practice it often occurs that while the main pipe is large enough for the transmission, the smaller pipes, or hose, through which the air is finally transmitted to the individual machines are too small, and velocities as high as 50 feet per second are not infrequently met with. Compressed air has usually to be transmitted a greater or less distance from the compressor to the place where it is used, and in computing the cost or the economy of opera- tions in which compressed air is employed it becomes necessary to consider the friction of the air in the pipes, and the power lost in overcoming it. Upon this point some very extravagant and widely erroneous ideas have been quite generally disseminated. The popular impres- sion is that great power losses are inseparable from the transmission of air through pipes. The facts are quite dif- ferent from this. It seems to be certain that power maybe transmitted by compressed air for considerable distances with less loss than by any other known means. We can- not do anything for nothing, and of course there is some loss of power in the transmission of compressed air, but in general practice thus far, unless the piping system has been outrageously bad and inadequate, the losses by transmission have not been worth considering. The distances traversed have usually not been great enough to make the loss a serious one, or at all to be compared with the losses of power through the heating of the air in compression, or through its loss of volume by the cooling of re-expansion when the air was finally employed. But as compressed- air practice develops we want longer lines, and then the 112 COMPRESSED AIR. question of transmission rises to greater importance. We want to convey air long distances for the purpose of em- ploying unused and now worthless water-powers. We want long lines of piping for supplying street-cars with the means of propulsion and for the general distribution of power and the general application of compressed air to its multifarious uses in large cities. We want to convey nat- ural gas from the wells where it flows to the towns and cities, where it may be used to the best advantage. When we come to look up the formulas to depend upon for our computations, we do not find any that are satis- factory and reliable. The best that may be said of the best of them, and that with caution, is that they are approxi- mately correct, but we know that they must be in error in some particulars. The available data in this line are meagre and chaotic, inconsistent and self-evidently unre- liable. It is perhaps too much to expect that close accu- racy can ever be attained in these computations. There are too many factors in the case, and a little variation in any one may make a great difference in the result. A state- ment of the friction in the case of compressed air flowing through a pipe involves at least all of the following factors : Unit of time, volume of air, pressure of air, diameter of pipe, length of pipe, and the difference of pressure at the ends of the pipe, or the head required to maintain the flow. Neither of these factors can be allowed its independent and absolute value, but is subject to modifications in deference to its associates. The flow of air being assumed to be uniform at the entrance to the pipe, the rate of flow is not constant for the whole length of the pipe, nor indeed for any point but the beginning of it. As the air may be said to carry in itseW, in its elasticity, its own means of propul- COMPRESSED-AIR TRANSMISSION. 113 sion, some of which it is using as it goes along, it is con. stantly losing some of its pressure, and its volume is there- fore constantly increasing. If the quantity of air entering the pipe is to continue to flow through it, the linear velocity of flow must be constantly accelerated on account of this increase of volume. This also modifies the use of the length of the pipe as a constant factor. It would be very natural to assume, as in the formulas in general use it is assumed, that if a certain head were sufficient to main- tain a certain flow for a given length of pipe, double the head would be sufficient for double the length. But that could not be so ; for in the second length all the head that propelled the air through the first length has disappeared, and the volume is now greater through the loss of that pressure, and the velocity is now greater, and it must require more additional head for the second length than was re- quired for the first. So of the other important factor, the diameter of the pipe. The actual area of section, or the apparent capacity of the pipes, is, of course, directly as the square of the diameter, but the volume of air transmitted for given length and head will not be in any such ratio. The surface resistance of the interior is proportionately much greater in the smaller pipe. While the area is as the square of the diameter, the periphery is directly as the diameter. The greatest distance of any portion of the air from the periphery being less in the smaller pipe, the viscos- ity of the air counts for more. For volumes in proportion to the areas of the pipes a i-inch pipe will require for a given length more than three times as much head as 'a 2- inch pipe. Then besides the fluctuating values of these fickle fac- tors there is that other factor, unrecognized in our compu- 114 COMPRESSED AIR. tations, but arrogantly assertive in practice the condition of the pipe itself. The actual diameter of wrought-iron pipe, especially in the smaller sizes, is different from the nominal diameter. Some pipe is smooth, and some has seams and blisters. The pipe may be straight, or it may be crooked and have numerous elbows. Everybody knows that elbows are unpleasant things to encounter. Tables have been published of the effect of elbows in retarding the flow of compressed air. One of these tables, copy- righted, is before me, and from it I gather that eight or ten i -inch elbows have a retarding effect equal to one length of pipe, so that if the table is to be believed, elbows are not as obstructive as they are commonly supposed to be. If we say, without copyright, that a single elbow is equal to a length of pipe we will be nearer right than the table. No table or formula can make allowances for foreign substances or obstructions in the pipe, and it seems unnec- essary to call attention to the necessity of thoroughly blow- ing out the pipe before it is put to use. Long lines of pipe are sometimes laid through a variety of rough coun- try, and before the pipe is coupled up many things get into it that have no right to be there. In pipe-lines for transmitting natural gas it has been the practice before the pipes were put to service to turn on the full pressure of the gas and blow out the pipe. The pressure in such cases is often as high as four or five hundred pounds to the inch, and under such a force the pipe is usually quite effectually cleared, stones, sticks, leaves, squirrels, rats, and snakes having sometimes been ejected. And here it might be proper to say a word about the importance of the unimportant. It is the general practice of pipers when running a line of pipe for air or water or COMPRESSED-AIR TRANSMISSION. H5 steam to put the white lead, or whatever may be used as a cement for the joint, into the coupling or elbow or other " female " fitting, wiping it around and filling the threads with it, and then when the end of the pipe or the " male " thread is screwed into it, none of the cement is left upon the outside, and a neat and clean-looking job is the result. The trouble in the case is that the job would not be so neat and cleanly looking if it could be seen from the in- side. As the pipe end is screwed into the fitting the ce- ment that does not remain in the threads and not much of it does remain in the threads is carried forward before the end of the pipe, and, when the pipe is screwed home, remains there and hardens, often rising above the inner sur- face of the pipe enough to cause a considerable stricture or reduction of pipe area. Now, if instead of this the cement- ing material is put upon the male thread when the pipe is screwed in, all that is not taken up by the threads remains on the outside of the pipe, instead of inside ; and although it does not look as neat as by the other practice, and en- tails the labor of wiping off the joint, we know that the in- side of the pipe is clear. FORMULA FOR THE FRICTION OF AIR IN PIPES. D = Diameter of pipe in inches ; L Length of pipe in feet ; V ' Volume of air delivered in cubic feet per minute ; Jf= Head or difference of pressure required to overcome friction and maintain the flow. Il6 COMPRESSED AIR. * 10,000 D b a jff * ~ "VALUES OF a FOR DIFFERENT NOMINAL DIAMETERS OF WROUGHT-IRON PIPE. li' 3 8" T T 2 C .787 io" . 1.125 , . . 12 . . . .662 4 ".. 84 12".. ,, 16" ... ' 6 ".... 20" , , 34 24".. It will be noticed that the values of a for the i^" and the i-J" pipes are not consistent with the values given for the other sizes of pipe. This is in recognition of the actual diameters of those two nominal sizes of wrought-iron pipe, which are 1.38" and 1.6 1" respectively. FIFTH POWERS OF D, 1 ".... i 3"---- 243 8".... 32,768 i" 3.05 3!" 525 10" 100,000 1 1" 7-59 4" 1,024 12" 248,832 2 " 32 5 " 3,125 20" 3,200,000 2 J".... 97.65 6".... 7,776 24".... 7,962,624 COMPRESSED-AIR TRANSMISSION. II? Two or three examples are offered showing the applica- tion of the above formulas, although their use should be sufficiently evident to anyone capable of making the com- putations. The volume, V, is of course the actual volume of the air as it flows through the pipe under pressure, and not the volume of free air. Say that we wish to transmit 1200 cu. ft. of free air per minute at 75 Ibs. gauge pressure, or 6 atmospheres, through a 4" pipe for 1000 ft., what additional pressure or head will be required to overcome the friction and maintain the flow of air ? 1200 cu. ft. of free air -f- 6 = 200 cu. ft. at 75 Ibs. gauge. Then 20O 2 X IOOO H = - - = 4.65 Ibs. head required. 10,000 X 1024 X .84 Having a 4" pipe 1000 ft. long and a head of 5 Ibs., what volume of air will be transmitted per minute ? ' j/ io.000 X 10.4 X^^g = IOOO ' The volume of free air in this case jvill be dependent upon the pressure during the transmission. If th.is 207.38 cu. ft. were under a pressure of 60 Ibs. gauge, or J 'atmos- pheres, the volume of free air would be 207.38 X 5 = 1036.9 cu. ft. If the pressure were 90 Ibs. gauge,*6r 7 atmospheres, the volume of free air would be 207.38 X 7 = 1451.66 cu. ft. Having 2000 cu. ft. of free air per minute compressed to 100 Ibs. gauge, through what length of 6" pipe may it be transmitted, losing 10 Ibs. pressure in the transmission ? Here the terminal pressure would be 90 Ibs. gauge, or 7 at- Il8 . COMPRESSED AIR. mospheres, and the volume would consequently be 2000 -r- 7 = 285.7 cu. ft. Then ,. _ 10,000 X 7776 X i X 10 _ 285.7 a Having 1500 cu. ft. of free air per minute to transmit a distance of 2000 ft., the air being at 80 Ibs. gauge, and wish- ing to deliver it at 75 Ibs., what should be the diameter of the pipe? Here we have a head of 5 Ibs., and the air is delivered at a pressure of 6 atmospheres, so that the deliv- ery-volume will be 1500 cu. ft. -f- 6 = 250 cu. ft. Then we have 2 so 2 X 2000 JD a = - - = 2500 in. 10,000 X 5 This is the only case where the fifth power can possibly make any trouble for us, and by referring to the following table of values of D*a for the regular sizes of pipe the necessity of struggling with the fifth root is avoided. VALUES OF D 6 a. i" 35 5" 2,918.75 ii" 1.525 6" 7,776 ii" 5-03 8" 36,864 2 " 18.08 10" 120,000 2i" 6 3 .47 12" 313,528 3 " 177-4 16" 1,405,091 3i" 413-2 20" 4,480,000 4" 860.2 24" 11,545,805 Our answer above being 2,500, we note that it is less than 2,918.75, the value of D"a for 5" pipe, so that a 5" pipe will be a little larger than is required by the conditions, and COMPRESSED-AIR TRANSMISSION. IIQ is the size of pipe that should be used. We may verify this by assuming a 5" pipe and computing what head would be required, the other conditions remaining unchanged. 250 X 2000 _ 10,000 X 3125 X .934 As this head is somewhat smaller than 5, the given head, this also shows that as" pipe would be a trifle larger than would be required by the conditions, while a 4" pipe would be much too small. The pressures to which air is compressed do not in practice always, or generally, occur in even atmospheres. The following table, VIII, will be found convenient in as- certaining the actual volume of compressed air at any given pressure if the volume of free air is given, or vice versa. TABLE VIII. TABLE OF THE RELATIVE VOLUMES OF COMPRESSED AIR AT VARIOUS PRESSURES. Volume of Volume at Volume of Volume at Gauge Pressure. Free Air for i Cu. Ft. at given given Pressure for i Cu. Ft. of Gauge Pressure. Free Air for i Cu. Ft. at given given Pressure for i Cu. Ft. of Pressure. Free Air. Pressure. Free Air. O I I 45 4.061 .2462 I .068 9356 50 4.401 .2272 2 .136 .8802 55 4-74 .2109 3 .204 8305 60 5.08 .1967 4 273 .7861 65 5.421 .1844 5 34 .7462 70 5.762 1735 10 .68 5951 75 6. IO2 .1638 15 2.02 .4949 80 6.442 .1552 20 2.36 .4236 85 6.782 .1474 25 2-7 .3703 90 7. 122 .1404 30 3.041 .3288 95 7.462 .1340 35 3.381 2957 100 7.802 .1281 40 3.72 .2687 I2O COMPRESSED AIR. The second column in the above table gives the volume of free air for i cu. ft. of compressed air at a given pressure, and this value may be used as a multiplier for any number of cubic feet at given pressure to ascertain the equivalent volume of free air. Having 550 cu. ft. of air at 80 Ibs. pressure, what will be the volume of free air ? 550 X 6.442 = 3548.1 cu. ft. The third column in the table gives the volume of air at any given pressure for i cu. ft. of free air, and this value also may be used as a multiplier for any number of feet of free air to ascertain its volume after compression to a given pressure. If we have 1750 cu. ft. of free air, what will be its volume when compressed to 65 Ibs. ? 1750 X .1844= 322.7 cu. ft. The following table, IX, of the head or additional press- ure required to overcome friction in the flow of air in pipes has been computed by the preceding formulae. It is be- lieved to be correct and reliable as far as it goes, and should be a convenience in many cases of compressed-air trans- mission for rock drills and similar uses. A table covering all the various pressures and conditions in general practice would be too voluminous to offer here. As we have before remarked, so many conditions may combine to modify the specific case of transmission that both the formulas and the table here given can have only a rough and general application and a provisional usefulness until something better appears. COMPRESSED -A IR TRA NSMISSION. TABLE IX. 121 TABLE OF HEAD OR ADDITIONAL PRESSURE REQUIRED TO DELIVER AIR AT 75 LBS. GAUGE PRESSURE THROUGH PIPES OF VARIOUS SIZES AND LENGTHS. i-inch Pipe. Linear Volume Length of Pipe in Feet. Velocity in of Feet per Free Air Sec. per Min. 50 100 150 200 300 500 1000 12.72 25 245 .4944 735 .98 1.47 2-45 4-9 25-44 50 .981 1.962 2.943 3.924 5.886 9.81 19.62 38.16 75 2.23 4.45 6.68 8-9 13.35 50.88 100 3.925 7.85 11.77 15-7 i^-inch Pipe. Velocity in Volume of Length of Pipe in Feet. Feet per Free Air Sec. per Min. 50 100 150 200 300 500 1000 6.7 25 .0567 .1134 .1701 .2268 .3402 .^67 1-134 13-4 50 .2268 .4536 .6804 .9072 1.3608 2.268 4.536 26.8 100 .9072 1.8144 2.7216 3.6288 5.4432 9.072 18.144 40.2 150 2.0412 4.0824 6.1236 8.1648 12.2472 20.412 i|-inch Pipe. Velocity Volume Length of Pipe in Feet. in . of Feet per Free Air Sec. per Min. 50 100 150 200 300 500 1000 4-9 25 .0172 .0344 .0516 .0688 .1032 .172 .344 9.8 50 .0688 .1376 .2064 .2752 .4128 .688 1.376 19.6 100 .2752 5504 .8256 I . 1008 1.6512 2-752 5.504 29-4 150 .6192 1.2384 1.8576 2.4768 3.7152 6.192 12.384 39-2 ' 2OO I . 1008 2.2016 3.3024 4.4032 6.6048 i i . 008 22.016 122 COMPRESSED AIR. TABLE IX. {Continued.} 2-inch Pipe. Velocity Volume Length of Pipe in Feet. in of Feet per Sec. Free Air per Min. 50 100 ISO 200 300 500 1000 6.369 50 .0192 .0384 .0576 .0768 .1152 .192 .384 12.738 100 .0768 .1536 .2304 .3072 .4608 .768 1.536 19.107 150 .1728 .3456 .5184 .6912 1.0368 1.728 3.456 25.476 200 .3072 .6144 .9216 1.2288 1.8432 3.072 6.144 31-845 250 .48 .96 1.44 1.92 2.88 4.8 9.6 38.214 300 .6912 1.3824 2.0736 2.7648 41.472 6.912 13.824 Pipe. Velocity Volume Length of Pipe in Feet. in of Feet per Free Air Sec. per Min. 100 200 300 400 500 1000 2000 8.163 100 .0428 .0856 .1284 .1712 .214 .428 .856 16.326 200 .1712 .3424 .5136 .6848 .856 1.712 3.424 24.489 300 .3859 .7718 I-I577 1.5436 1.9295 3.859 7.718 32.65 400 .6848 I . 3696 2.0544 2.7392 3.424 6.848 13-696 40.81 500 1.072 2.144 3.216 4.288 5.36 10.72 21.44 3-inch Pipe. Velocity Volume Length of Pipe in Feet. in of Sec. per Min. 100 200 300 400 500 IOOO 2000 5.659 100 .01647 .03294 .04941 .06588 .08235 .1647 3294 11.318 200 .06588 .13176'. 19764 .26352 3294 .6588 1.3176 16.977 300 .14823 .29646 .44519 .59292 74II5 1.4823 2 . 9646 22.636 400 .26352 .52704 .79056 1.054 1.3176 2.6352 5.2704 28.295 500 .41175 8235 1.233 1.647 2.058 4.1175 8.235 56.59 IOOO 1.647 3.294 4.941 6.588 8.235 16.47 COMPRESSED-AIR TRANSMISSION. TABLE IX. (Continued.} 3|-inch Pipe. 123 Velocity Volume Length of Pipe in Feet. in of Feet per Free Air Sec. per Min. 100 200 300 400 500 1000 2000 I0.66I 250 .04202 .08404 .12606 . 16808 .2101 .4202 .8404 21-32 500 .16808 .33616 . 50424 .67232 .8404 1.68 3.36 31.98 750 .37817 .75634 I-I345 1.5127 1.89 3.78 7.56 42.64 1000 .67232 1-344 2.0169 2.6893 3o6 6. 72 13.446 53-3 1250 1.0505 2.IOI 3.I5I5 4.202 5-25 10.505 21. OI 4-inch Pipe. Velocity Volume Length of Pipe in Feet. in of Feet per Free Air Sec. per Min. 100 200 300 400 500 IOOO 2000 I5-QI 500 .08074 .16148 .2422 .3229 .4037 .8074 1.615 23.86 750 .18166 .3633 545 .7266 .908 1.816 3.633 31.82 IOOO .32296 6459 .969 1.29 1.615 3-229 6-459 39-77 1250 .5046 1.009 I.5I4 2.018 2.523 5.046 10.092 47-73 1500 .7267 1-4534 2.18 2.907 3.633 7.267 14-534 5-inch Pipe. Velocity Volume Length of Pipe in Feet. in of Feet per Free Air Sec. per Min. 500 IOOO 2000 3000 4000 5000 10000 IO.I8 500 .11896 .2379 -4758 -7I37 9517 1.189 2-379 20.36 IOOO .4758 9517 I-9033 2.855 3-8067 4.758 9.516 30.54 1500 1.0706 2.1413 4.2826 6.424 8.565 10.706 21 .41 40.72 2000 I.9033 3 8067 7.613 11.42 15-227 I9-033 50.90 2500 2-974 5.948 11.896 17.844 23-79 29.74 I2 4 COMPRESSED AIR. TABLE IX. (Continued.} 6-inch Pipe. Velocity Volume Length of Pipe in Feet. in of Feet per Free Air Sec. per Min. 500 1000 2000 3000 4000 ,5000 10000 14.18 1000 .1786 .3572 .7144 1.0716 1.428 1.786 3.572 21.27 1500 .4018 .8037 1.6074 2.411 3-215 4.018 8.037 28.36 2OOO .7144 1.4288 2.857 4.286 5.715 7.144 14.288 35-45 2500 1. 116 2.232 4.465 6.697 8-93 II . 162 22.325 42-54 3000 1.607 3.215 6-43 9.645 12.86 16.075 32.15 8-inch Pipe. Velocity Volume Length of Pipe in Feet. in of Feet per Free Air Sec. per Min. 1000 2000 4000 6000 8000 10000 15000 15.91 2OOO .296 592 1.184 1.776 2.368 2.96 4-44 19.88 2500 .4626 .9 2 5 1.85 2-775 3-7 4.62 6.939 23.86 3000 .6661 1.332 2.664 3-996 5.329 6.66 9-99 31.82 4000 1.184 2.368 4-737 7.105 9-474 11.842 17.76 39-775 5000 1.85 3-701 7.402 II. 103 14.8 18.505 27-757 lO-inch Pipe. Velocity Volume Length of Pipe in Feet. in of Feet per Free Air Sec. per Min. 2000 4000 6000 8000 10000 15000 20000 IO.I8 2000 .1844 .3688 5532 .7376 .922 1.383 1.8.44 12-73 2500 .288 .5763 .8644 1.1526 1.44 2. l6l 2.88 25-46 5000 I.'S 2-35 3.458 4.61 5.763 8.644 ii. 5 38.19 7500 2-59 5.186 7-78 10-37 12.967 19.45 50 92 1 0000 4.61 9.22 13-83 18.44 23.05 COMPRESSED-A IR TRA NSMISSION. TABLE IX. ( Continued.} 12-inch Pipe. 125 Velocity Volume Length of Pipe in Feet. in of Feet per Free Air Sec. per Min. 2000 4000 6000 8000 10000 15000 20000 8.84 2500 .11075 .2215 332 443 5537 .83 1.1075 ; 17-68 5000 443 .886 1.329 1.772 2.215 3-322 4-43 26.52 7500 .9967 1-993 2.99 3-987 4-98 7-47 9.96 ! 35.36 10000 1.772 3-544 5.316 7.088 8.86 13.29 17.72 j 44.2 12500 2.769 5.538 8.3 11.07 13.84 20.74 CHAPTER XIII. THE UP-TO-DATE AIR-COMPRESSOR. THE principal thing to be said of the up-to-date air-com- pressor is that it is not up to date. It would be difficult even now, and notwithstanding the improvements which we are told have been made in air-compressors in the last few years, to find the one that embodies the best knowledge of the- time, or that in actual performance accomplishes what should be expected of it with our present knowledge of the practical conditions of economical compression. The standard of performance for a single-stage air compressor may be taken to be : a cylinderful of free air at normal temperature compressed isothermally, and ail delivered to the receiver, by an apparatus involving no losses through friction, and we should expect to realize a nearer approach to that standard than we do. We should in the first place be able to ascertain what is actually done in economical air- compression to-day, and if any one undertakes that he will find that it is no simple task. The catalogues of air com- pressor manufacturers are interesting in this connection, and the alleged indicator-diagrams contained in them are worthy of study. I have learned from them, if nothing else, to respect the wisdom of the builder who does not allow the diagrams from his steam- and air-compressing cylinders to be seen. While, as we know, air-compressors are built and running with the air-compressing cylinders placed tandem to the ISO THE UP-TO-DATE AIR-COMPRESSOR. 12-7 steam-cylinders, the piston rod of the steam-cylinder being continued into the air-cylinder and transmitting all the power required for compression directly to the compressing piston, and with a friction loss of only 5 per cent between the steam-cylinder and the air-cylinder, there are indicator- diagrams published in builders' catalogues that show very different results. In one set of diagrams, bearing every evidence of genuineness, but published without data, the ratio of the air-cylinder M.E.P. to that of the steam- cylinder is .633, a loss of over 36 per cent in power alone, saying nothing of the other inevitable losses. In another catalogue a set of alleged indicator-diagrams is given with some accompanying data, and with a ratio of air-card to steam-card of .818, a loss of 18 per cent. A diagram from an air-compressing cylinder, published by another manu- facturer, shows the air-admission line above the atmosphere- line for almost the entire length of it, as though the air would rush into the air-cylinder with alacrity when the pressure was higher within the cylinder than outside of it! Still another builder, commenting in his catalogue upon this phenomenon, says that the fact that the air-admission line is above the atmosphere-line proves that his rival's piston leaks. I have in my possession still another indicator- diagram from a compressing cylinder with newly patented valves, and in which the air pressure in the cylinder at the beginning of the compression-stroke is ten pounds above the atmosphere, although the cylinder is filled with free air at each stroke and the entire compression is done in that one cylinder. And so it goes. We may say that the air- compressor builders are living upon the ignorance of their customers, or we may say that the blind are leading the blind, as may seem most correct for the individual case. 128 COMPRESSED AIR. Of all the steam-actuated air-compressors in existence the one showing the very worst results, as far as economy of steam for the service performed is eoncerned, is the air- compressor used upon locomotives for operating the air- brakes. To compress a given volume of free air to a cer- tain pressure the " air-brake pump " uses nearly ten times as much steam as would be required in the best air-com- pressors of the day for the same service. The air-brake pump, however, is the one compressor whose extravagant waste of steam is condoned by the circumstances surround- ing its employment. There are more than 30,000 of these pumps in use, a number greater, perhaps, than that of all other air compressors combined, not counting those that are used for beer. While the wastefulness of this pump is fully conceded, its persistent use for air-brake service is completely vindicated. The pump is very simple and always ready, which is an important point, and the steam used to operate it upon the locomotive is mostly steam that otherwise would be blown off by the pop safety-valve. The pump is usually worked when stops are made at stations or when running down grade, and if the pump used much less steam it would generally mean not that so much steam was saved, but that the safety-valve would have so much more to do. Various styles of air-brake pumps have been devised showing a much better economy, but they have been successively abandoned for the estab- lished pump. It is only when the air-brake pump is used for the purpose of a general compressed-air supply, as it quite frequently is in railroad shops, that its extravagance is to be condemned. In such cases no language can be too severe to characterize the folly of it. That the air-brake pump can be used with profit and satisfaction to supply THE UP-TO-DATE AIR-COMPRESSOR. 129 compressed air for general use speaks highly of the value of the air. As a mechanical curiosity, and as exhibiting a great achievement of ingenuity, a set of indicator-diagrams from an air-brake pump are here reproduced, Fig. 20 being from Fig. 2O. the steam-cylinder and Fig. 21 from the air-cylinder. The steam-cylinder diagrams are so different from the familiar cards of the ordinary steam-engine cylinder that it has been thought best to place the arrows upon them to indicate the direction of motion. They would look more natural to the Fig. 21. general steam engineer if he could be allowed to read them in the reverse way. It will be noticed that the steam pressure in the cylinder is low at the beginning of the stroke, corresponding with the low resistance in the air- cylinder, and that the steam pressure rises with the progress of the stroke, and at the end of it the cylinder is full of 130 COMPRESSED AIR. high-pressure steam, while that steam has done much less work than would be due to the dead pressure of that volume of steam, saying nothing of the additional power that could have been developed by using expansively. This is evi- dently a more wasteful application of steam even than in the direct-acting pump for water. This distribution of steam, however, accomplishes the designed purpose of approxi- mately equalizing the steam pressure to the resistance, and the air-brake pump is thus enabled to dispense with the crank-shaft and all which it implies. Under any arrangement that has been invented for using steam economically the pressure in the steam-cylinder during the earlier part of the stroke is at its highest, and decreases generally to nothing, or nearly nothing, at the end of the stroke. In opposition to this the resistance in the air-cylinder at the beginning of the compression-stroke is very low and increases as the piston advances, and at the latter part of the compression-stroke this resistance is con- siderably higher than the force of the steam that is driving the piston. To keep the compressor in motion it is not enough that the mean effective pressure upon the steam- piston for the whole stroke shall exceed the mean effective resistance against the air-piston plus the friction of the entire apparatus. The force and resistance must be equal- ized in some way to keep up the movement, and various devices have been employed for this purpose. The usual reliance at the present time is upon the weight of the reciprocating parts and heavy fly-wheels, and it is doubtful still if there is anything that is in all respects to be preferred. A novel and ingenious arrangement for accomplishing this desired object has lately been brought out by one of the air-brake companies, not so much, it is understood, for air- THE UP-TO-DATE AIR-COMPRESSOR. 13 l brake service, as for general use in air-compression. The two air-cylinders of this compressor are horizontal and single-acting, and they together form the foundation for the entire compressor. While they are together equal in free air capacity to a double-acting cylinder of the same diameter and stroke, they are in other respects quite differ- ent, as the pistons have movements independent of and always different in speed from each other, except momen- tarily at a point near the middle of each stroke. Above the air cylinders is placed the steam-engine, which forms a part of and which actuates the air-compressor. The engine comprises the usual elements of the horizontal steam- engine the steam-cylinder and its piston, the cross-head, connecting-rod, crank-shafts, fly-wheels, and the mechanism of the valve motion. Short connecting-rods attached to the cross-head give motion to two compensating levers with changing fulcrtims, and through these levers power is trans- mitted to the air-compressing pistons; and with a uniform movement assumed for the cross-head a continually decreas- ing movement is given to each air-piston for its compres- sion-stroke. At the beginning of either stroke of the steam- piston the fulcrum of the equalizing lever is above the middle of it, and the air-piston moves faster than the steam- piston. At the latter part of the stroke of the steam-piston the fulcrum of the lever is nearer its lower end, and the air- piston then moves much slower than the steam-piston. The indicator-diagrams Fig. 22 show the practical opera- tion of this compressor. The upper diagram, from the steam-cylinder, shows the steam at 100 pounds cut-off at four tenths of the stroke. The dotted line of the diagram shows the effect of the steam pressure for the stroke as modified by the weight and inertia of the reciprocating I3 2 COMPRESSED AIR. parts. The lower diagram, from the L.r-cylinder, exhibits American Machinist Air Cylinders Fig. 22. the operation of compressing free air up to and delivering THE UP-TO-DATE AlR-COMf>RSSOR. 133 it at 100 pounds pressure. The dotted lines in this diagram show the resultant force from the steam-piston as trans- mitted by the action of the compensating lever to the air- piston. It is evident that the work required of the fly-wheel in this case is less than in the ordinary steam-engine, while in the common air-compressor it is much greater. These cards show the friction of the compressor to be high, the ratio of the air to the steam-cylinder diagram being .75, a loss of 25 per cent from this source alone. The full sponsorial and patronymic appellation of the most pretentious member of the air-compressor family to-day is the Corliss Cross-Compound Condensing Com- pressor. It may be called the Five C's. The " cross " is not practically as good as the tandem, but commercially the alliterative effect is valuable. The Corliss feature is one of the most valuable adjuncts for selling the com- pressor, but has nothing to do with operating it. The Corliss engine, as everybody knows, is designed to main- tain a uniform speed under a varying load. The cut-off controlled by the governor, is changed as the load changes and because the load changes. The air-compressor is required to maintain a constant air pressure when there is a varying demand for the air, and this varying demand means of course, and can only mean, a varying speed of operation, so that to take a fully equipped Corliss stationary engine and to attach an air-cylinder tandem to the steam- cylinder, or, if a double or compound engine, to attach an air-cylinder tandem to each steam-cylinder, the propriety of the arrangement must be very evident to those who can see it. All computations upon the efficiencies of air-com- pressors have been based upon the assumption of constant work under the best conditions. When it is recognized 134 COMPRESSED AIR. that no compressed-air service is uniform in its demands, then the sacrifice of ideal conditions that the varying demand entails becomes quite an important factor in determining the ultimate economy of the system. How a compressor is governed is a very pertinent question for the economist. I cannc/t afford to go into it here, but I may say that nine tenths of all the air-compressors in use, not including the air-brake pumps, have no governors, and the governing devices employed upon most of the others are crude, unsatisfactory, and generally disgraceful. Where large air-compressing plants are to be established for continuous service, a much higher ultimate economy can be attained than where the plant required is not so extensive. It is best to use a number of units for the work of compres- sion instead of one or two large compressors. Air-com- pression offers little or no opportunity for the storage of power or for doing any work in advance, as may be done by a water-pump and reservoir. The receivers used in con- nection with air-compressors will not usually hold more than the compressor can deliver in one minute, so that if the demand for the air fluctuates it must be met by the speed of delivery at the compressors, and not by a change of reservoir supply. Air-compressors, like simple steam- engines, have their conditions of speed, pressure, etc., that secure the best economy; and where a plant consists of a number of units, all in operation, it will usually be more economical to let most of them, or as many as possible, run steadily at their best, and to do the governing or equalizing of the work by one or two of the compressors rather than by all of them. The more extensive the air-compressing plant may be or the more extensive the use of the air compressed the more uniform the demand may be expected to be. CHAPTER XIV. COMPRESSED AIR VERSUS ELECTRICITY. THE title of this chapter is adopted in deference to the prevalent idea of the relations of these two power-trans- mitters. To my thinking the versus should be read as lightly as it is possible to read it, for there is in fact but little antagonism or competition between compressed air and electricity, and there is little likelihood that in practice there ever will be. Neither of them is a power-transmitter pure and simple, as a wire rope may be said to be, but each is capable of performing other functions, and the power- transmitting capabilities of each, in combination with their other individually peculiar lines of usefulness, open for each a distinct and separate field, which neither can fill for the other. The same is true of some of the other power- transmitters. They each have their special fields of useful- ness and adaptability which neither of the others could fill as well, if at all. Of late the gas-engine has been coming rapidly to the front as a valuable agent in the development, transmission, and distribution of power, and it has its enthusiastic advo- cates who are ready to predict that before long it is to supersede every other motor over a field that is practically boundless. But upon looking over the field a little farther and listening to another group of enthusiasts it soon appears that not the gas-engine but the oil-engine is the coming 135 136 COMPRESSED AIR. motor, and not only is it the coming motor, but it has already come, and is driving out the electric and gas and other motors, and the steam-engine also, in England and Germany and elsewhere in Europe, and it must soon do so also with us in the United States. But as we look into the operating conditions under which these several agencies may find employment we soon learn that each of the several motors is most applicable under conditions of its own, and that neither can do all that either of the others can do. Gas and oil, of course, develop power as the steam-engine does, while compressed air and electricity can only trans- mit power that originates elsewhere. But with the devel- opment and transmission of power the usefulness of gas (" producer " gas) or of oil ends, while with air and elec- tricity power-transmission is not their only function. Electricity has the vast field of illumination, in which it reigns supreme ; compressed air has no one application to compare in magnitude and importance with that of electric lighting, but it has a vast number of duties which are all its -own, and which electricity cannot touch. The use of com- pressed air has been slow of development, and is still back- ward, but at this writing I am able to enumerate two hundred distinct and established uses of compressed air, and in more than 90 per cent of those uses electricity is absolutely inapplicable, and in the remainder, which form a field more or less open to other agencies besides either air or electricity, the air generally has the advantage. Turn to the last chapter of this little book, wherein some of the uses of compressed air are enumerated, and see all those that come under the first letter of the alphabet and judge where the competition with electricity comes in. In our list of the applications of compressed air some of the other COMPRESSED AIR VERSUS ELECTRICITY. 1 37 letters of the alphabet develop a larger enumeration than the first letter, and the use of air for operating motors, or for producing rotary motion in general, or for performing any of the functions of the steam-engine, is not" included. Referring to the portion of the list under the letter A, it will be noticed that the only applications of air that compete with electricity are the air-brake and the air-hoist or the air- jack. The electric brake in competition with the air-brake is anything but a success, and it is not worth further men- tion. Even upon electric cars the air-brake is an absolute necessity for safety, and hundreds of lives have been sacri- ficed in our city streets because it has not been used. The air-jack also has the field to itself, and electricity is "not in it." In the field of general hoisting air and electricity divide the work, and the line of service done by each is gen- erally distinct from that performed by the other. There are establishments where they are thoroughly familiar with the uses and capabilities of electricity, operating, for in- stance, electric travelling cranes, and yet which use com- pressed air in numerous places throughout their works for hoisting, and where for the special services required electric- ity would have no chance at all. Where the direct-acting vertical hoist can be used, or the air-cylinder, either verti- cal or horizontal, with multiplying sheaves and a wire rope, it is, of course, preferable to electricity with its spinning motor-shaft, its drums and gearing. In the general work of hoisting as carried on at the Armour Packing Company's vast establishment electricity could not possibly do the work that the air does. The wonderful capability of standing ready for instant use at full power and without cost for maintenance for long periods of time seems to be possessed by compressed air alone. It is pre-eminently adapted to t3 COMPRESSED AIR. uses that call for constant alertness, as in the switch and signal service and in the air-brake, and in the air-hoist it stands at its post day and night ready to give a lift the instant it is called upon. In the lines of service to which electricity and com- pressed air seem to be, perhaps, equally applicable, and where they could compete with no apparent disadvantage to either, it is to be regretted that circumstances seem invariably to defeat a fair comparison. In driving pumps a very fair test could be instituted of the relative merits of each, and of the losses in the use of each, as power-trans- mitters, and it happens that in this very work of pumping we find some striking illustrations of what might be termed the constant bad luck accompanying the air, or the malig- nant opposition of circumstances to any fair exhibition of its powers. Compressed air, by its very accommodating attitude, by its very applicability to widely varying con- ditions, is constantly placing itself in a false position before the community and showing itself at a disadvantage. It is able to accept conditions that enable it to make an un- seemly and unjust exhibition of its powers, yet which entirely exclude electricity from any such depreciatory performance. The pump that can be operated by electric- ity can be operated equally well by compressed air, the air- motor taking the place of the electric motor, either of them producing rotary motion ; and with suitable connecting gearing and with the pump mechanism unchanged one would have as good a chance as the other, and under those con- ditions the air could be made to do better than the elec- tricity. Electricity seems to be making advances more rapid than ever before in its employment for railway traction. It COMPRESSED AIR VERSUS ELECTRICITY. 139 drives the horses from the surface roads, and is now be- ginning to supersede the steam locomotive. Perhaps all do not realize that this is the triumph after all of the steam engineer more than of the electrical engineer. Electricity is demonstrating not so much its superiority as a power-trans- mitter, but is simply showing the ultimate economy of gener- ating power in large central plants, even if the means of dis- tribution is a wasteful one, and accompanied by features that are insurmountably objectionable. The extending use of electricity as a railway motor is an argument also for com- pressed air, for it is able to take full advantage of the economy in centralized power development, and we are in the way to see very soon some practical demonstration of its abilities in this field. In railroad service, as in every- thing else, compressed air has been heretofore unfortunate, and its advocates and would-be promoters have wasted time and opportunity in developing minute economies in the air-motor which were not needed to enable it to com- pete with the best in the field. It may be regarded as cer- tain that whatever gain may be shown in the employment of electricity for traction its establishment is by no means a final solution of any question except of the economical generation of power, and that electricity has nothing to do with. Has any one called attention to the fact that one of our most prominent and perplexing political questions is entirely and indisputably the product of compressed air ? Can electricity claim to have contributed any prominent factor in determining the course of parties or in shaping the destinies of the nation ? What if compressed air should be found to hold the balance of power and the deciding voice in the selection of a future President of the United States ? 140 COMPRESSED AIR. This is the actual situation, and not an absurd or exag- gerated statement of it. The only political function attained by electricity is that of public executioner. Elec- tricity and compressed air stand to each other as the masked and nameless headsman upon the one side and Warwick the King-maker upon the other. The silver ques- tion of the day, whichever side of it we may find ourselves on, is entirely the outgrowth of the increased output of silver, and that, no one can deny, is what the air-driven rock drill has accomplished. The precipitation upon us of this perplexing question may have been a work of question- able beneficence, but the power that could achieve it is not to be treated lightly. CHAPTER XV. THE THERMAL RELATIONS OF AIR AND OF WATER. IN all of our operations with compressed air, either in its compression, its storage and transmission, or in its final application to whatever purpose, the temperature of the air at any time, and the effect of raising or lowering its temper- ature by whatever means, are always important facts to be considered, and it will be well for us as early as possible to fix in our minds some general ideas upon the subject. The thermal relations of water are so different from those of air that by contrast a knowledge of the one may be made to enforce our knowledge of the other. The fact also that the effects of heat upon water are accepted as standards of heat measurements makes it necessary for us to know something about them. Say that we apply a given quantity or unit of heat to a pound of water, raising its temperature i degree ; how much air would be equally heated, or have its temperature raised i degree, by the same unit of heat ? A cubic foot of air at atmospheric pressure " free air " and at 62 degrees weighs .076 pound, and a pound of air therefore in vol- ume equals i -4- .076 = 13.158 cubic feet. A pound of water is 27.7 cubic inches, and the ratio of volumes of water and of air of equal weight will be about i 1821. But, pound for pound, it takes less heat to raise the tem- 141 142 COMPRESSED AIR. perature of air i degree, or any number of degrees, than is required to raise the temperature of water the same num- ber of degrees. The specific heat of water being i, that of air is only .2377, so that 13.158 cubic feet -f- .2377 = 55 cubic feet, and this 55 cubic feet of free air is to be com- pared with i pound, or 27.7 cubic inches, of water. There is a means of fixing the thermal relations of air and water in the mind's eye so that they may not be easily forgotten. A common-sized glass tumbler, not quite full, holds a half-pound of water. A cubical box measuring 3 feet each way, or say a large dry - goods box, holds, of course, a cubic yard, or 27 cubic feet, which is, nearly enough, a half of our 55 cubic feet, so that the dry-goods box full of air and the tumbler full of water represent quite closely the volumes of air and of water that will be equally heated by equal units of heat. The approximate ratio of vol- umes will be i : 3431, and the ratio of the sides of two cubes representing the two volumes will be i : 15 + The isometric projection of the two cubes here shown (Fig. 23) may convey and impress the relations better than the figures can do it. It is to be remembered that in the transmission of heat either to or from air or water that is, whether heating or cooling them, or whether cooling or heating any bodies in thermal communication with them the above ratios will prevail. Those whose attention is called for the first tims Fig. 23. THERMAL RELATIONS OF AIR AND WATER. H3 to the phenomena accompanying air-compression or expan- sion cannot fail to be struck with the great changes of temperature that ensue coincidently with either operation, but the actual heat represented by these changes is usually overestimated, although circumstances that should check the exaggerated estimate are also at hand. If the body of the air-compressing cylinder and the cylinder-heads are properly water-jacketed, the temperature of the air deliv- ered is considerably lower than it would be if there were no water-jacketing, but, at the same time, the perceptible heating of the water in the jacket, by which the partial cooling of the air is effected, proceeds quite slowly, show- ing that the actual quantity of heat abstracted from the air by that means is not great. So also when the heated com- pressed air flows through pipes for some distance, the rapid- ity with which its temperature approaches that of its envi- ronment is another evidence of the small amount of heat actually carried by it. Still we hear constantly of the won- ders of heating or cooling that are to be done by compressed air wonders that never fully materialize with a more ex- tended experience. In the Pohle " air lift pump " ( which is not properly a pump, as it has absolutely no moving or working or wearing parts, but which is a very valuable ap- plication of compressed air direct for raising water from bored wells, and where the air is discharged upward into the submerged end of a vertical water-pipe, the air entering the pipe, distributing itself through the water, and rising with it, expanding as it rises) it is claimed that the expansion of the air while in contact with the water cools the water. We may say that the expanding air certainly does cool the water, and we may also say that it certainly does not cool the water more than a fraction of a single degree. 144 COMPRESSED AIR. Where an establishment is equipped with a permanent compressed-air plant, for operating hoists, jacks, presses, and isolated machines of all kinds, it is a simple matter to rig up an arrangement for cooling the drinking-water for the employes. Take a ij" pipe 100 feet long (50 feet might be long enough), place it horizontally, and connect one end of it to the compressed-air supply, with a suitable cock to control the escape of the air. Leave the other end of the pipe open and enclose the whole of the pipe, after passing the air- admission cock, in a thick non-conducting covering. If nothing better is at hand, take plenty of paper, and wind it on spirally layer after layer, covering the whole pipe. Then lead a " water-pipe into the open end of this hori- zontal released air-pipe, and let it come out by a tee or otherwise at the other end of the air-pipe, and the whole apparatus is provided. The air in this case should be thor- oughly cooled and have all its suspended water discharged before its release in the cooling-pipe. A touching spectacle in all our large cities are those mel- ancholy monuments of a futile philanthropy, its public drinking-fountains. The motive that prompts their erec- tion is worthy of all respect. Much money has been ex- pended upon them with the best of intentions, but with the poorest of results. They can nowhere be said to be a suc- cess, for they do not accomplish what they propose to do. They offer the cup to the thirsty lip, but it is practically an empty cup, for it does not hold what we want. Who wants to drink warm water ? The most costly and artistic of fountains is nowhere, in the thought of the hot and thirsty crowd, in competition with a bucket of cold -water and an old, rusty tin dipper. The instinctive call of hu- manity for cold water to drink is so absolutely universal THERMAL RELATIONS OF AIR AND WATER. 14$ that it must be correct, and should be more adequately provided for. Our cities are constantly doing more and more for the comfort and well-being of all the people. To all of us life is more worth the living by reason of our co-operation and our collective helpfulness. Amid all that is designed to make our cities more attractive and more desirable to live in, is there any possible material thing that can be sug- gested more to be desired, more proper to do, more promis- ing of universal good, than to make it possible for every man, woman, and child to have always at hand a drink of cold water ? Does not compressed air make it possible ? The establishment of a general compressed-air service in any city might be gloriously celebrated by the establish- ment of a cold-water fountain. If anyone does undertake to cool drinking-water by the use of compressed air, we may expect to hear that it takes a great quantity of air to cool a little water, which is just about what I have been writing above. The case, how- ever, in the matter of cooling by compressed air is not nearly as bad as I seem to make it appear. The actual heat represented by any change of temperature in air com- pressed to a pressure of several atmospheres is of course greater than for air compressed to only i atmosphere, or free air, as we call it, and directly in proportion to the re- spective absolute pressures, With air at 75 Ibs. gauge, or 6 atmospheres, the same change of temperature in either heating or cooling would indicate a transfer of six times the amount of heat that would be indicated by the same heat- ing or cooling of free air. The sudden release of air com- pressed to 6 atmospheres and at 62 before the release would cause a theoretical fall of temperature of over 200, H COMPRESSED AIR. and if this air were in communication with water that re- quired to be cooled but 20, this would give the air a con- siderable advantage. In the case of the Pohle air lift pump, cited above, where the volume of water would prob- ably be as great as that of the compressed air in contact with it, the cooling effect of the expanding air could be but slight, as before stated. CHAPTER XVI. THE FREEZING UP OF COMPRESSED AIR. THE most familiar and the most constantly reiterated objection to the use of compressed air is its well-known habit of "freezing up" under certain conditions, and too many who have not sufficiently investigated the subject have regarded this freezing-up of the air as an insurmount- able and fatal objection to its use for purposes for which it would seem to be otherwise eminently adapted. By " the freezing up of the air," as the expression is commonly used, although, of course, it is never the air that freezes, we understand a deposition of moisture, more or less rapid, upon the sides of the pipes or passages that convey the air, and its accumulating and freezing there until the area of the channel is materially reduced, the proper flow of the air prevented, and the operation of the air-motor or other apparatus seriously impeded or stopped entirely. This phenomenon may easily occur and has frequently occurred in the use of compressed air. The earlier experimenters in this line all encountered it, and most of them on account of it at once dropped compressed air as a practicable power- transmitter, and the freezing up of compressed air has remained a formidable bugaboo among otherwise intelligent mechanics to this day. The best way to do in a case like this is first of all to have a good look at it all around in broad daylight. It COMPRESSED AIR. would seem to be worth while to get together where we can see them the principal facts of the case, so that we may be able to understand the conditions under which the freezing up occurs, whether it must always accompany the use of compressed air, and, if not, the combination of conditions under which all danger of freezing up may be successfully avoided. Intelligent mechanics to maintain their up-to-date in- telligence must be wide-awake and fully informed, and such should know that in these days compressed air is widely used not only without freezing up, but also without any reheating or other special device for preventing it. Com- pressed-air locomotives, probably hundreds of them, are constantly used, in mines and elsewhere, without any re- heating of the air and without freezing up, and the builders of those locomotives will absolutely guarantee them to do it every time. Rock drills by the thousand and pumps and hoisting-engines without number are run by compressed air without reheating it and without freezing up. It must be evident that for freezing up to occur two things are essential, and neither alone could have any effect toward producing such a result. The free moisture must be present and accumulating, and the temperature of the air where the freezing up is to occur must be below the freezing-point. The moisture alone can cause no trouble as long as the temperature continues high enough. It will simply be carried along with the air and will be dis- charged with it. So, too, a low temperature of the air in the passages at any time will not freeze up anything as long as there is no free moisture present to be frozen. We may say generally that air always contains moisture. Its capacity for moisture is determined by the combined THE FREEZING UP OF COMPRESSED AIR. 149 conditions of pressure and temperature to which it is at the time subjected. Changes either of pressure or of tempera- ture immediately change the capacity of the air for water, and, supposing the air to be saturated with water, whenever, either through increase of pressure or through decrease of temperature, the capacity of the air for water is reduced, the excess of water is dropped. At constant temperature the capacity of air for water seems to be inversely as its absolute pressure. By another mode of stating this it may be said that the capacity of the air for water is independent of its pressure or density. It is so stated by parties who have an eminent right to speak upon the subject ; and the statement is correct if rightly understood, but it is apt to be misleading. At uniform temperature a given volume of air implies a capacity for a certain weight of water, whether the air be at a pressure of i atmosphere or of 100 atmos- pheres; but if the air has been compressed from a press- ure of i atmosphere to a pressure of 100 atmospheres, or if its volume has been reduced from, say, 100 cubic feet to i cubic foot, or in that proportion, its capacity for water has really been reduced to one hundredth of its original capacity; and if the air before the compression was saturated with water, then after the compression, and after it has fallen to its original temperature, it must have dropped somewhere during the operation ^ffo of the water that it originally carried. At whatever pressure the air may be changes of temper- ature immediately affect the capacity of the air for carrying water. The water-carrying capacity of the air seems to be as sensitive to temperature as to pressure. We know very distinctly the general fact that the hotter the air the greater its capacity for moisture ; but there seem to be little satis- 1 5 COMPRESSED AIR. factory data as to the quantity of water that will be carried by compressed air under different conditions of tempera- ture. The absence of such data, however, need not seriously cripple us in our quest. In the operation of air-compression the heating of the air, and the increase of water capacity thereby, seems to keep pace with and to compensate for the reduction of water capacity consequent upon the reduction of volume, and we never hear of any trouble from -liberated water in the compressing cylinder, but after the air leaves the com- pressor the water begins to make itself known, and all the world hears of it. As the air leaves the compressor it is usually quite hot, and even at the high temperature the air is usually saturated, or nearly saturated, with water. As the air cools the water begins at once to be released, and before it is thoroughly cooled considerable water is generally depos- ited. Changes in the meteorological conditions, or in the original humidity of the air as it enters the compressing cylinder, of course change the amount of water precipitated by the air after compression, and all who have experience with compressed air find that on this account the air carries and deposits more water at some times than at others. Many amateurs and experimenters have encountered trouble from the freezing up of the air on account of taking the air immediately from the compressor, before it has been completely cooled, or, if cooled, by neglecting to drain off all the liberated water from the pipes before using the air. The experience thus obtained embodied an important lesson if it could have been learned, but the lesson has been too often misread, and the interpretation of the freezing up phenomenon has been an incorrect one. When an air- motor or an engine driven by compressed air " freezes up," THE FREEZING UP OF COMPRESSED AIR. I$I usually by the choking of the exhaust passages, the general impression among mechanics is that the water is precipi- tated by the air at the moment when the freezing occurs ; but the fact usually is that the water is deposited in the pipes by the air before the motor or engine is reached, and the water is then carried along as entrained water by the friction of the air, and when the temperature of the air falls below the freezing-point, on account of its expansion in the cylinder or at the exhaust, the water, being present and in contact with the cold air, is of necessity frozen. The general practice of the day in the compression and transmission of air does not seem to make adequate provi- sion for disposing of the water deposited by the air while cooling. As the air leaves the compressor it is usually quite hot, and even at the high temperature it is saturated or nearly saturated with water. As the air cools it begins at once to lose its capacity for water, and some of the water is dropped and continues to be deposited as long as the air continues to cool. In connection with the compressor, and usually quite near it, a receiver or reservoir of considerable capacity is provided, the most important function of which is, or is assumed to be, that of collecting the water that may be precipitated by the compressed air. In too many cases this receiver fails of its mission, or only partially collects the water from the air, because, if the compressor is working constantly and rapidly, as it usually does, the air goes through the receiver and out of it and into the pipe-line before it has time to cool. The air after compression will not drop all of its water until it is thoroughly cooled, and the cooler it gets the greater will be the quantity of water liberated ; and when the air, still under full pressure, has reached the lowest pressure attainable, means should then 152 COMPRESSED AIR. be provided for collecting the liberated water, or it must, of course, be carried along in the pipes to make trouble by freezing up where the air is used, and where the air expands and cools while doing its work or upon its release. With a receiver near the compressor, and with hot air passing through it, and a pipe-line long enough to completely cool the air before it is used in rock drill, air-motor, pump, or other constantly running machine, and with no provision for dis- posing of the water in the pipe, we should expect to hear of the machines freezing up. Cases are quite common where a second receiver placed at the farther end of a pipe-line has effectually cured the freezing up by removing the congeal- able liquid. A few years ago many air-compressors for driving rock drills were in use in the United States a large number of them upon the Croton aqueduct which cooled the air dur- ing compression by the injection of jets of water into the air in the compressing cylinder. Compressors of this style are not now built by any firm in the United States. The cylinders were found to wear out quite rapidly, the compressors could not be run as fast as the dry compressors, and for other similar reasons they did not pay. They did, however, deliver the compressed air decidedly cooler than the compressors now in use deliver it, and it is not surprising that it should be claimed by rock-drill runners, and probably correctly, that those old injection compressors, with the water intimately mingling with the air during the compression, still furnished drier air, and consequently air less liable to " freeze up," than the more modern dry compressors furnish. In the process of wood-vulcanizing, for preserving wood by cooking the sap in the wood, the material to be treated is enclosed in tight cylinders and subjected to an air press- THE FREEZING UP OF COMPRESSED AIR. 1 53 ure of 150 pounds. The air is specially heated and made to circulate around and among the wood and absorb the moisture that may be liberated from it, so that it is essential to the process that the air should be as dry as possible, and the paradox occurs that to secure dry air the wet or injec- tion type of compressor is employed. I know a certain iron mine which has two air-compressors side by side, each connected to deliver the compressed air through the same receiver and the same pipe to the rock drills in the mine. One of the compressors delivers its air at a temperature considerably below that of the air from the other compressor, say from 50 to 100 lower, neither of the compressors being of the injection type, and it is con- stantly noted that the men in the mine operating the drills can immediately tell which compressor is running by the relative humidity of the air supplied. The compressor which delivers the coolest air of course delivers the driest air. When the air is completely saturated with water, contact with water will not make it any wetter. The water in the injection compressor did not wet the air, for it was as wet as it could be ; and as that water enabled the compressor to deliver the air at a lower temperature than the dry com- pressor would deliver it, the air, simply because it was cooler, actually emerged from the compressor bearing less moisture than the air emerging at the same pressure, but at a higher temperature, from the dry compressor. If no means were provided for draining the surplus water from the air, except, in either case, the receiver located near the compressor, the cooler air passing the receiver would carry the less amount of water into the pipe and through it ; but if, in each case, after the air had traversed the pip_e a suffi- cient distance to have become thoroughly cooled another receiver or drainage chamber had been provided, there is 154 COMPRESSED AIR. no reason why, after emerging from the chamber, the air in each case being at the same pressure and temperature, the one should carry any more water than the other. To get rid ot all trouble from water in the air, and the possible freezing of it, care should be taken that when the air passes a point where it is still at full pressure and has reached its lowest temperature, such means of drainage shall be provided that none of the liberated water shall be carried into and along the pipes beyond that point. The possible freezing up that we have been contemplat- ing thus far along in this chapter is where water is present by deposition from the compressed air, and where a low temperature is caused by the expansion of the air, and the freezing of the water ensues by contact. Another mode of freezing up is experienced where the freezing is accom- plished not by the air that has been compressed, but by the external atmosphere. In the winter if compressed air at low temperature, but still above the freezing-point, saturated with water, as it is pretty sure to be, and with the pipe thoroughly drained to a certain point, has then to pass for some distance through a pipe exposed to a freezing atmos- phere, it cannot fail to deposit some water, and the freez- ing of the water so deposited may soon choke the pipe. I have encountered cases of this kind more than once, notably in one of the largest chemical works of the country, where the pressure of the air is employed in lifting and transferring acids so that they may not be exposed to metallic contact. The air-pipe was carried through the extensive works and from building to building, and in some places between the buildings where exposed to the extreme cold of a sharp winter it was choked up by the accumulation and successive freezing. The only apparent lesson in this case is to protect the pipe from frost. A pipe conveying compressed air and- THE FREEZING UP OF COMPRESSED AIR. 155 exposed to a freezing atmosphere is quite sure to choke up. The deposition of the water may proceed slowly, but if the low external temperature continues, the accumulation will eventually reduce the air-channel, or even close it entirely. This result is, of course, chargeable to the weather, and not to the innate frigorific malignity of the compressed air. The pressure at which the compressed air is transmitted, and eventually used, has an important bearing upon the question of its freezing up in use. If the air is transmitted only short distances, and at comparatively low pressures the probabilities of freezing up are much greater than if high pressures are employed and if the distance of trans- mission is at least sufficient to allow a thorough cooling and drainage of the air while under the full pressure. In the use of low-pressure air for any service, of course a larger volume of free air is used to furnish any given power, and the larger volume of air implies the presence of a greater quantity of water in suspension, and the lower pressure em- ployed affords less opportunity, or no opportunity, for ex- tracting the water, and, as a fact of experience, most of the freezing-up trouble that is encountered is from air that is used at comparatively low pressure. There are many considerations, which I need not enu- merate here, to commend the use of air at high pressures, and not the least among those considerations is the practical immunity from freezing up that is thereby secured. This may be readily understood Say that air is compressed to 1000 pounds gauge, or, say, 70 atmospheres, either that smaller pipes may be used for long-distance transmission, or that smaller receivers may be used for the storage of air upon a street railway motor, and say that the air is admitted to the motor at 100 pounds pressure. If while the air is at 1000 pounds it is thoroughly coolgdrg^j? foam^ it is evi- tt N T VT. T? Q T T 1 **T t 156 COMPRESSED AIR. dent that when that air is expanded to 100 pounds, and has been allowed to regain its normal temperature, if the air was just saturated with moisture when at 1000 pounds pressure and normal temperature, when it has expanded to more than eight times its former volume it can be only one eighth saturated, and no water can be deposited by it in expanding from 100 pounds downward, and however low the temperature may fall there can be no freezing up. A valuable use of compressed air is for the transmission of packages or mail matter through suitable tubes from one station to another. In this pneumatic transmission service some trouble has been experienced in the winter from the accumulation of ice in the pipes. As the pressure employed is low the freezing up might be prevented by compressing all the air to a pressure considerably higher than required and cooling and draining it while under that higher pres- sure. Then after passing a reducing valve to the low pres- sure for use the air would be dry and could not deposit moisture to be frozen. Compressed air is often used in caissions for bridge piers and kindred uses where the compressor is so near the cais- sion that the air in transmission does not become as cool as it should be, and the men find the warm atmosphere very oppressive and are unable to do as much work as should be expected. The service pipes are sometimes cooled by pass- ing them through water, but even then the air in the caissons is warmer than it should be for vigorous work. In this case also if the air were compressed to a pressure, say, 20 or 30 pounds higher than required, then cooled as well as possible by passing the pipes through cold water, and after that ad- mitted to the caisson through a pressure -reducer adjusted to the desired pressure, it would then be cool enough, or it might even be made cooler than required. CHAPTER XVII. REHEATING COMPRESSED AIR, WHILE air at low temperature has a comparatively small cooling effect upon water or upon whatever may be in con- tact with it, the fact inversely applied is of advantage in the use of compressed air for power-transmission. It requires comparatively little heat to raise the temperature of air rapidly. It is well known that after the transmission oi compressed air to the point where it is to be employed a considerable saving in the cost of the available power is effected, theoretically at least, by reheating the air before it is used. While many have called attention to this matter in various ways, few have given us any definite and reliable data regarding it. Little is generally known as to the actual economy of such a practice, or of the conditions under which it is practicable It may easily be shown that where a certain volume of air has been compressed to a given pressure, and has by transmission or storage resumed approximately its normal temperature, if that air is then reheated and thereby ex- panded, the additional volume of compressed air resulting from the expansion is produced by an expenditure of heat much lower than the original volume of compressed" air was produced for, and by a much lower expenditure of heat than is required to produce an equal volume of steam. The actual figures in the case, all theoretical, are as follows : I 5 COMPRESSED AIR Weight of i cu. ft. of steam at 75 Ibs gauge = .2089 Ib Total units of heat in i Ib. of steam at 75 Ibs from water at 60 = 1151. Total units of heat in i cu ft of steam at 75 Ibs 1151 X ,2089 = 240.44. To produce by compression through a steam-actuated air-compressor i cu, ft of compressed air at 75 Ibs. and 60 about 2 cu ft of steam of the same pressure are required. or the heat-units employed in producing i cu. ft of com- pressed air will be about 240.44 X 2 = 480 88 heat units as the thermal cost of i cu. ft. of compressed air at the above temperature and pressure The temperature and volume of the air as it leaves the compressor will be considerably higher than the figures here assumed, but as the air is in- variably stored for a time, or is transmitted through pipes to a distance, between its compression and its ultimate employment, it may be said to always return to its normal temperature before it is used, so that, whatever we may have at the compressor, the air as it is delivered to the motor, or whatever apparatus may be operated by it, will have cost, as above stated. 480.88 heat-units for i c\i. ft at 75 Ibs The difference in the thermal cost of any volume of compressed air thus produced by mechanical compres- sion and the cost of any additional volume of air that may result from the subsequent reheating of the air is very striking. The weight of i cu ft of free air at 60 = ,076 Ib. Weight of i cu. ft of compressed air at 75 Ibs, and 60 -.456 Units of heat required to double the volume of i Ib of air at 60 = 123 84, Units of heat required to double the volume of i cu ft REHEATING COMPRESSED AIR. 159 of compressed air at 75 Ibs. and 60 = 123.84 X .456 = 5 6 -47- Cost of i cu. ft. of superheated compressed air at 7 5 Ibs. compared with the cost of i cu. ft. of compressed air as produced by ordinary compression: 480.88 .'56.47 : : i : .1174. Here we see that the cost in heat-units of the volume of air produced by the reheating is less than one eighth of the cost of the same volume produced by compression. Upon this showing the matter is certainly worth looking into, because if there is such a possible opening for the econom- ical application of heat to the development of power, we ought to know it and avail ourselves of it. The operation of reheating compressed air is correctly so termed. It is, in fact, a case of doing work over again, or of replacing in the air heat that has been lost by it in previ- ous operations. It must be confessed that the presumption is all against our finding much profit in this direction There are not many places in life where it pays to do our work a second time There is, as we have seen, practically no air-compression without heating the air by the operation, and there is no transmission of air after compression with- out its cooling to very near its original temperature If the air could go immediately from the compressing cylinder into the motor cylinder, where it does its work, without losing any of its heat, it would have the same effective power as it would have after long-distance transmission and cooling and reheating, and without the additional cost of that re- heating. While we are saying in all good faith that there js little loss of power in the transmission of compressed air COMPRESSED AIR. to considerable distances, and that the difference in the pressure of the air at the two ends of a long pipe necessary to overcome the friction and maintain the flow is but smal), and that it is, to a great extent, compensated for by the increased volume at delivery, the fact still is that there is a great loss of power in the transmission of the air, if we reckon from the moment when compression ceases on ac- count of the inevitable cooling of the air. Still this loss is not properly chargeable to the transmission, for no matter how far the air may be transmitted the cooling is all accom- plished before the air has travelled very far if the pipes are of proper size. Supposing air to be transmitted ten miles, it must be conveyed with considerable rapidity if it does not get down to normal temperature before the end of the first quarter of a mile. As the volume of air under any constant pressure varies directly as the absolute temperature, it follows that to double the volume by heating the air its absolute tempera- ture must be doubled. The air being at 60, its absolute temperature will be 60 -f- 461 = 521, and double this will be 521 X 2 = 1042, the absolute temperature required. This by the thermometer will be 1042 461 581. As this is the temperature that is required for the air when delivered into the motor, and actually beginning its work, it will be necessary, on account of the ease and rapidity with which it cools, to heat the air considerably higher than this theoretical temperature. It is one thing, and an eg^y one, to heat the air, while it is a very different and a \;ery difficult thing to keep it hot. To avoid all loss of heat it would be necessary, not only to keep the pipe which con- veyed the air constantly hot, but also the cylinder in which REHEATING COMPRESSED AIR,. l6l it was used, oc it would be cooled before it began to do its work. In one case within my experience, where com- pressed air was reheated, and its absolute temperature was increased at the heater 38 per cent, and where, of course, its theoretical increase of volume was the same, the actual increase of power realized was only 12 per cent. In this case the air was transmitted after the reheating about 20 feet, the pipe was not covered, and no precautions were taken to prevent loss of heat by radiation. The volume of air transmitted was sufficient to develop between 20 and 30 horse-power. The theoretical temperature re- quired to double the volume of compressed air at 60 being 581, the actual temperature required at the heater under the most favorable conditions in order to have a double volume of air available in the motor will not be less than 800, and this is a temperature that it is practically impos- sible to employ and maintain, and we may as well give up all thought of doubling the volume of compressed air by reheating it and of realizing the promised economy of the operation. If instead of doubling the volume we only attempt to increase it by one half, or 50 per cent, which it is practica- ble to do, the required theoretical temperature (absolute) will be 521 + 50 per cent = 782, and 782 461 = 321, the sensible temperature required. Adding enough to this to allow for the intermediate cooling, the actual temperature required should probably be not less than 450. The tem- perature of the air before the reheating being assumed to be 60, the increase of temperature will be 450 60 = 390. As we saw above that it required 56.47 heat-units to raise the tempeature of i cu. ft. of compressed air at 75 Ibs. gauge pressure from 60 to 581, the actual increase of tern- 1 62 COMPRESSED AIR. perature being 581 60 = 521, it follows that to raise the temperature 390 will require : 521 1390 :: 56.47 142.27. Then if the first cubic foot of compressed air costs 480.88 heat-units for its compression, and if the additional half of a cubic foot produced by reheating costs 42.27 heat-units, the total cost of i^ cu. ft. under the reheating system will be 480.88 -f- 42.27 = 523.15, and the cost per cubic foot at this rate will be 523.15 -s- i-J = 348.76 heat-units. The relative cost in heat-units of i cu. ft. of compressed air pro- duced by compression alone, and of a cubic foot resulting from compression and reheating, will be : 480.88 : 348.76 : : i : .72. From this it appears that the gain by reheating com- pressed air sufficiently to increase its effective volume 50 per cent will be 28 per cent. The more fair and correct way to state this, however, will be to reverse it : .72 : i : : i : 1.38. We may say, then, that, the total fuel applied with the reheating system will yield 38 per cent higher results than are to be realized without the reheating. This seems to be very near the maximum that can be attained in the way of economy by reheating dry compressed air. It is not always, nor, indeed, often, that the reheating of compressed air is practicable or possible. In a valuable report upon compressed-air appliances by a committee of the Master Car-Builders' Association, 1894, they say: "It was reported by the manufacturers of air-appliances that superheated compressed air used in air-lifts, jacks, engines, REHEATING COMPRESSED AIR. 163 etc., increases the efficiency fully 50 per cent, but your committee was unable to make tests or to procure reliable data, etc." The "manufacturers of air-appliances," quoted by the committee, either were not responsible for their words or they did not know what they were talking about. Bearing in mind the facility and rapidity with which heated air in transmission loses its heat, it is idle to think of ever heating compressed air except for continuously running motors, and then by heaters very close to the motors. In Paris, where 25,000 horse-power is employed for general compressed-air service, the air in some instances is used to run engines that were formerly run by steam, the original boiler that supplied the steam for the engine being retained as a heater and reservoir for the air. That is all right, and wherever any motor or engine is to be run without inter- ruption a heater for the air should certainly be employed ; but at the end of this volume is a list of two hundred dif- ferent and distinct uses of compressed air in not one of which would it be practicable or anything but a losing op- eration to try to heat the air. In the United States at the present time there is probably not one case in a thousand where compressed air is employed and where one cent of profit could be realized from reheating the air. It is to be regretted that American compressed-air practice is not so far developed, or developed upon such lines, as to make the economy of reheating the air before its use more readily and generally available. When, by and by, compressed air comes to be used for what we may term legitimate power- transmission, and is employed to drive small motors and motors not so small with the established functions of the steam-engine, then the reheater will find its field of useful- ness. 164 COMPRESSED AIR. In connection with this topic it is hoped that the accom- panying diagrams, Figs. 24 and 25, will be of some interest and value. Fig. 24 shows the increase of volume accom- 1 Volume \\ II h r. I i I i tb * Volu panying the heating or reheating of compressed air. The air is assumed to be heated from the several initial temper- atures of o, 32, 60, and 100, the pressure remaining constant during the operation represented. The relative REHEATING COMPRESSED AIR. l6 5 volume at any temperature is indicated by the height of the vertical line corresponding with that temperature, the height from AB to CD representing one volume, and each Gage Pressures horizontal line above that indicating, successively, an additional one tenth of volume. When the line EF is reached, the original volume is doubled. Figures below the base-line AB indicate the sensible temperatures 1 66 COMPRESSED AIR. Fahrenheit, and the figures above the upper line indicate the corresponding absolute temperatures. Fig. 25 shows the increase of pressure only caused by the heating of compressed air, the volume being constant. The air is assumed to be heated, as in Fig. 24, from the several initial temperatures of o, 32, 60, and 100, and also from a number of different initial pressures. The pressures are indicated by the several horizontal lines, the vertical distance between any two adjacent lines represent- ing approximately i atmosphere. The figures at the left of the diagram indicate the gauge pressures, and the figures at the right the absolute pressures. The temperatures are in- dicated as in the previous diagram. CHAPTER XVIII. COMPRESSED AIR FOR PUMPING. THE air-compressor owes its modern development to the demands of the rock drill, in its various forms and appli- cations, more than to any other single cause. The larg- est builders of air-compressors for general use first engaged in their manufacture to supply the air to the rock drills that they were building. All of the rock drills in all of the mines, and in every tunnel that is being driven, and in every shaft that is being sunk, we may say, are and appar- ently must be driven by compressed air. Nobody seems to inquire, and nobody knows very clearly, whether or not the power employed in operating rock drills is applied economi- cally or not. The conditions under which the drills are employed and the nature of their work are all inimical to economy. It is impossible to measure the actual work done by a rock drill. It is enough that their work pays, and that there is little annoyance or anxiety involved in keeping them going all right. But, taking the mines as they run, the operating of the drills is only one of several uses of power in mining opera- tions, and not the largest of these, although to some it may seem to be the most important. Hoisting, including haul- age, and pumping, either of them, upon the average, re- quires more power than is required for the drilling. Good steam-engines at the surface may generally be employed 167 1 68 COMPRESSED AIR. for the hoisting, and they do so well that we need not here trouble ourselves much about them. With the use of power for mine-pumping it is all very different. The pumps must generally be located where the water is, and, if steam is used to drive them, far away from the boiler plant ; and it so happens that to-day probably the most wasteful use of steam to be found anywhere is to be found where mine pumps are operated. This certainly ought not to be so. The operation of pumping is one of the most favorable ever found for the economical application of power. The marine-engine and the water-works pumping-engine divide the honors as exam- ples of the highest economy in the wide range of modern engineering practice. The stationary engine, except under the most favorable conditions, does not equal their per- formance. The success of the marine-engine and of the pumping-engine is to be attributed to the one operating condition that they have in common, and that is not found elsewhere. They have constantly uniform work to do. The pumping of water from our mines should also be eco- nomically done, because in this service, almost as much as with the water-works pump, the height of the lift is practi- cally constant and unvarying. It is not necessary to say how different is the actual result in the case of the mine pump. Waste of power and expense for repairs, and for duplicate machinery, are the natural and inevitable accom- paniments of steam-pumping in deep or extensive mines. The trouble of course is principally in carrying the steam so far. Everybody should know that steam need not be employed under such conditions. Compressed air stands ready to do this work and to do it more cheaply and more satisfactorily COMPRESSED AIR FOR PUMPING. 169 than it can be done by any other means. It is to be con- fessed that air, where it has been employed for mine-pump- ing, has not by any means made as favorable an exhibit as it should have made, and has not made the progress that it should toward universal adoption for this service. The why of it is easily found. Here is a practical example in the case of what is said to be the largest coal-producing mine in the United States. Of course they have a lot of pumping to do there, and of course they use for it the always handy steam-pump. In this mine the steam is conveyed to the pumps by one line about a mile, and by another line about a mile and a half. The steam condenses all along its journey, and with high pressure at the boilers there is low pressure, and often too low pressure, at the pumps. What starts from the boilers as steam is mostly water when it gets to the pumps, and they are operated by combined hydraulic and vaporous ac- tion, the simple steam-pump thus becoming what might be termed a diabolically reversed compound. The great feat- ure of the American steam-pump is that it will actually go. That it will go in the mine makes it also go in the market. It is to be recorded to its credit (?) that it makes it possible to do what it should be impossible to do. And so we find in this mine eight of these pumps, in various grades of in- efficiency, and the steam is carried a mile or a mile and a half to make them go. The steam leaks everywhere, the roofs are rotting and tumbling in under the combined ac- tion of the heat and the moisture, sometimes joints blow out or pipes break, men are scalded, passages are blocked, ventilation is stopped, gangs of repairers are constantly em- ployed, but the troubles keep increasing. Something has COMPRESSED AIR. to be done about it. It will not do to use steam any longer here. When it comes to this point it is very unfortunate that this is a coal mine. A little item in the cost of a plant to be installed will outweigh all considerations of fuel or of power economy. The decisions of coal-mine managers are therefore no suitable precedents for the miners who must feed their boilers with greenbacks. Electricity or com- pressed air, either of them, stands ready to take up this job of pumping, and get rid of this steam nuisance in the mine. But electricity has no chance here, because new pumps would have to be bought, and there would be also the wir- ing of the mine, while compressed air is so accommodating that it agrees to use the old pumps and the old pipes, and no one need doubt that the pumps will actually go. Com- pressed air is accordingly adopted, not upon its merits, but because it will not cost so much to put it in ; and electric- ity is not permitted to make an unseemly exhibition of itself. Few perhaps realize how peculiar, and, indeed, unique, have been the conditions under which electricity has been spread abroad. In every case where it has been employed in power-transmission its installation has involved an en- tirely new plant throughout, each end of the plant has been adapted to the other, and every detail to the whole, so that it has never been placed in a false position or shown at a disadvantage, as compressed air is almost invariably served. If electricity had secured a chance at this mine, putting in the new electrically-driven pumps, as well as the generators, and with everything new, consistent, and complete, it would, no doubt, have put on airs over the results accomplished, as compared with what compressed air has done in some COMPRESSED AIR FOR PUMPING. I?I cases ; but there would have been, after all, really no basis for comparison. For supplying the compressed air instead of steam to this mine, an excellent compressor-plant is installed, a plant that any manufacturer might be proud of and might be pardoned for bragging about. The performance of these compressors is presumably as good as that of any compres- sors to be found to-day. But the air furnished by the com- pressors is to be used in those abominable steam-pumps. I have elsewhere expressed my disgust at, and protested against, the apparent indifference of the air-compressor builders as to the uses to which the air is put after it leaves the compressor, or as to whether the air is applied econom- ically 01 not. Too often the explanation in the case is the same as in this case, completely exonerating the compres- sor builders. The conditions determining the adoption of compressed air for this mine are that the old pumps are to be used. Of course the compressor builders cannot afford to kill their business to save their ideals ; they get a good job, and the compressors are put in to drive those pumps. It is not known that any worse contrivance has yet been discovered, as far as power economy alone is concerned, than the common direct-acting steam-pump. There are enormous clearances to be filled at every stroke of the pump, without any compensation for the waste or any justi- fication of its existence, except the very insistent one that the clearance is one of the conditions necessary to make the pump go, or is necessary when tired steam is used. Not the slightest advantage can be taken of the possible expansion of the steam or air. Too often the reverse of expansion occurs, and at the termination of the stroke the cylinder is filled to a higher pressure than was required to COMPRESSED AIR. make the stroke, and all the cylinderful to be immediately exhausted. This may be worse with a duplex than with a single pump, as either piston may reach the end of its stroke and the cylinder may then be overfilled with steam or air while it is waiting to have its valve reversed by the move- ment of the other piston. But it always happens, in addi- tion to this, that the pumps are not proportioned to the work to be done, or that the several pumps are not all so proportioned that the same pressure will operate each of them. Where the pumps were driven by steam trans- mitted a long distance, it might have been well to calculate upon lower steam as the distance increased, and to plan the pumps accordingly, but there is no calculation of the kind undertaken. The pumps are simply bought ready-made, and they fit about as well as other ready-made goods. Take the published list of the pumps in the mine that we are talking about. The actual heads under which the sev- eral pumps are operated is given, and I have added 10 per cent to the pressures due to those heads, and the operating pressures required in the steam-cylinders of the several pumps are then as follows : No. 12345678 Lbs. 32 28 10 31 39 23 37 32 No. 3 is a small pump and runs biu a short time each day, and is not of much account to us. Nos. 4, 5, and 6, however, are the largest pumps employed, located near each other, and delivering under the same head. If the above are not the several pressures required, they must be nearly in these ratios, and they seem to complacently ig- nore the fact that all the pumps should be operated by approximately the same pressure, especially if compressed COMPRESSED AIR FOR PUMPING. 1/3 air is used to drive them. The pump for which the lowest pressure is sufficient, running under throttle, is quite likely to fill its cylinder with air at the highest pressure before the exhaust occurs. Unless the piping is outrageously inade- quate the air pressure will be practically the same through- out the mine. In this mine the pipe capacity is liberal, and it is safe to assume that the air pressure in the pipes supplying these eight pumps will not be found to vary more than i Ib. or 2 Ibs. at the most throughout the series. At this writing, the air-plant having been in operation considerably over a year, I have the written word of the superintendent that its efficiency has not been to this day definitely ascertained. All of the pumps have not been operated at once except in emergencies. The most defi- nite statement obtainable is that with the compressors at a certain speed six of the eight pumps are run at once, which tells us nothing, as we do not know the speed of the pumps. It would be a simple matter, when everything was going, and at any time agreed upon, to station a man at each pump and let him count the strokes, and this, in connec- tion with the revolutions of the compressors, would tell us much. From a knowledge of all the available data in this case, and from some knowledge of similar cases, I am will- ing to hazard the assertion that not more than 20 per cent of the I.H.-P. at the steam-cylinders of the compressors is to be found in the weight of water delivered by the pumps. Of course the arrangement as it stands is a great improve- ment over the use of direct steam at the pumps, and every- body is to be congratulated over the change. Not only is there an actual reduction in the total consumption of steam, where it is used in the cylinders of the air-compres- sors instead of in the cylinders of the pumps, but all of the 174 COMPRESSED AIR. annoyance, delay, danger, and expense of the steam-distri- bution is avoided. That, with suitable pumps, a different air pressure in the pipes, and a consistent combination of machinery throughout, the same work could be done for one half of the fuel is not worth considering, for this is a coal mine, you know. But if the same work could have been done with one half of the boiler and compressor- plant, that would been worth considering even at a coal mine, and is deserving of much serious thought where the installation of additional plants is under consideration. Something may of course be said upon the other side of this case, and toward shifting the responsibility for it. Mine managers are not pump experts. The attitude of the pump builders is similar to that of the compressor builders. They simply sell the pumps and they know little about how people may employ them, as I have been told by agents and salesmen of pump establishments. No special pumps are built to be operated by compressed air. There should be such pumps in the market, and compressed air should not be used with any thought of economy in the common direct- acting steam-pump. The pump should be a geared pump, and the air-motor should be an engine with a cut-off adopted to the pressure of air employed. Right here seems to be offered a fine opportunity for comparison between electricty and compressed air for power-transmission. Pumping is a line of work that either may do, and with little apparent unfair advantage in the conditions. The same pumps that are being put in to be operated by electricity would be equally adapted to be opera- ted by compressed air, by the substitution of an air-engine for the electric motor and an adjustment of the gearing to correspond, and a fair comparison of the results might be COMPRESSED AIR FOR PUMPING. 1/5 made. In a Western town a pumping-plant has recently been installed to be driven by electricity. The pumps are bought by the town, and the local electric-lighting company undertakes to maintain and operate them, transmitting the current 2000 ft., for 4 cents per 1000 gals, delivered against a pressure of 60 Ibs., which is about twenty times the fuel cost for the same work in the best pumping-engines of the day. Electricity might sublet this contract to compressed air for one quarter of the figure, and the air would be greatly inflated over its good luck in getting the job. In the general work of pumping there is evidently a great field still to be occupied by compressed air. It is the natural power-transmitter, and incomparably the best, for mining operations ; and as the mine pumping requires more power than the rock drills, more compressed ail should be used in our mines for the pumping, while, as a matter of fact, probably not one quarter as much air is used, and steam or mechanical transmission of power is employed at great inconvenience and expense. A pressure of 6 atmospheres, which is very suitable for the rock drills, could also be used to good advantage for the pumps, and proper arrangements for cooling and draining the air would fully dispel all danger of freezing, which is the prevalent bugbear of compressed-air practice. Besides the pumping for mines there is the constantly recurring problem of power-transmission for the water- supply of towns and cities, and compressed air is well adapted for such service. With a general compressed-air service established in our large cities the air would be ready to operate the thousands of pumps, now driven mostly by isolated hot-air engines, which supply the tanks upon the roofs of high buildings, or of buildings on ground too high for the established water-supply to reach, g CHAPTER XIX. A LIST OF THE VARIOUS APPLICATIONS OF COMPRESSED AIR. THIS list is intended to include only the direct applica- tions of compressed air to specific uses, and not its employ- ment in an air-motor, or where it takes the place or does the work of a steam-engine or other power-developer. The list is of course incomplete, as such a list must necessarily be, for the applications of compressed air develop faster than they can become generally known and recorded. A slight explanation of the way in which the air is used is given in a number of cases. Acids, Raising or Transferring. Compressed air is largely used for this purpose in chemical works, or where acids are handled in bulk or in large quantities and where contact with the metals cannot be allowed. Vessels con- taining the acid are subjected to a pressure of air inside them and above the acid, and the pressure of the air causes the acid to flow wherever the pipe may lead it. Accumulator for Hydraulic Hoisting Service. The com- pressed-air accumulator takes the place of the heavy weights long used for maintaining a uniform and constant pressure and regulating the supply of water necessary in operating hydraulic cranes, lifts, etc. The air, compressed to the pressure required to be maintained, is contained in an up- right cylindrical vessel of considerable capacity. The water A LIST OF THE VARIOUS APPLICATIONS. \TJ rises and falls in the lower part of the vessel, and a consider- able fluctuation of level is possible without great change in the air pressure. A float upon the surface of the water controls the movement of a duplex pump to maintain the required water-supply. Aerated Bread. Aerated Fuel. A jet of compressed air vaporizes or atomizes crude petroleum in furnaces which have a wide ap- plication in the arts wherever great heat with perfect control is required, as in glass factories, brick or lime kilns, forges and metal works, etc. The system is also used for gener- ating steam, but for that purpose is not generally cheaper than coal. Lamps using compressed air with oil in a similar way are much used for out-of-door work, also in rolling- mills, railroad yards, etc. Aerating Molten Metal in the Bessemer Process. This was a revolutionary application of compressed air, and of untold importance in the manufacture and in the promotion of the use of steel. The air is forced up through a mass of melted cast iron, burning out the carbon and in a few minutes converting the entire mass into steel, thus produc- ing steel cheaper than iron. Aerating Water. The aeration of water is usually carried on in connection with its filtration, and is equally necessary in many cases to render the water wholesome and potable. Extensive works for the purpose are provided in connection with the water-supply of many towns and cities. The air is made to traverse a series of water-tanks, passing succes- sively up through the contents of each, carrying off volatile and objectionable constituents and imparting the necessary oxygen. Agitating Syrups in Sugar-refineries. 1 7 COMPRESSED AIR. Air-brake. The air-brake, in use upon all passenger trains, and also largely used for freight, puts the control of the train entirely with the engineer. Before the use of compressed air for this purpose the brakes upon each car were applied and released separately by individual brake- men upon steam-whistle signals from the engineer. The brakeman is discharged and the whistle is seldom heard. The air is compressed by an air-brake pump upon the locomotive, and there are over 30,000 of these air-brake pumps in use, a number greater, perhaps, than that of all other air-compressors together. The air-brake pump has begotten a great number of new applications of compressed air, especially in connection with the different departments of railroad service. Air-brake upon Street Railways. The value of the air- brake upon the steam-roads and the necessity for a quicker and more efficient brake for street-cars, now that the cable and the trolley have made them heavier and have increased their speed, are leading rapidly to the adoption of the air- brake for street-railway service. They air-compressing pump on the street-car is operated by a crank or eccentric upon one of the axles of the car. Air, Dense, see Dense-air Refrigerating. Air-hoist. This term is used in contradistinction to the pneumatic crane, the crane generally employing drums and gearing or other complicated mechanism, while the move- ment of the hoist is simple, direct, and of limited range. Air-jack. Air-jacks are largely used in railroad shops and are a distinct outgrowth of the air-brake pump, the pump being always at hand or easily procurable with other railroad supplies, and may be readily piped up wherever it may be wanted. The jacks are more properly air-lifts, usu- A LIST OF THE VARIOUS APPLICATIONS. 1 79 ally operating from below the load to be lifted. Many jacks are sunk in specially prepared pits under repair tracks for taking out wheels and axles. Portable jacks are in use which have wheels and handles like a barrel truck. Stand- ing the truck up sets the lifting cylinder upon its base, and the jack is at once ready for work. The air pressure is supplied by an air-hose connected with a convenient branch upon the air-supply pipe. " Pulling down " jacks are made for pulling down defective sills upon freight cars. Air-lift Pump. The Pohle air-lift pump is not prop- erly a pump, except that it is employed for raising water, and it has no working or moving parts of any kind. A vertical water-pipe, usually in a bored or artesian well, ex- tends down some distance below the level of the water to be lifted, and at the lower end of it, which is open, a com- pressed-air pipe discharges the air upward into the column of water, and the mingled air and water rise and flow from the upper end of the water-pipe. The flow of water con- tinues as long as the air is supplied. The pump gives ex- cellent economical results and is highly commended. Air-lifts, see Elevators. Air-lock Doors. The air-lock is used for the ingress and egrees of workmen and material to and from caissons, the excavating chambers of soft-ground tunnels, or wherever operations are carried on under air pressure. The lock is a chamber of sufficient size to receive two or more men at a time or a bucket of material. It is provided with two sets of doors and valves to admit or discharge the air. To enter the working chamber the outer door of the lock is opened, then the men enter the lock and this door is closed. A valve is opened admitting air from the working chamber until an equal pressure is attained in 180 COMPRESSED AIR. the lock, when the inner door may be opened and the men admitted. The same operation occurs in the admission of material, and the process is reversed for egress. By a late improvement the outer doors of the air-lock are opened and closed by the pressure of the air acting upon pistons connected with the doors, and the locks are operated more rapidly than formerly, especially for the hoisting or lowering of material. Applying Hose-couplings. Armor, Diving, see Diving-armor. Asphalt-refining, see Refining Asphalt. Automatic Pump, see Ejector. A utomatic Fire-extinguisher. Balloon, Water, see Raising Ships. Beating Eggs. Beer-pump. The use of compressed air for forcing beer from barrels, for the retail trade in saloons and hotels, must be more extensive than its use for the air-brake. The air pressure for this service is either provided by hand power or automatically by hydrant pressure. Bell-ringing, see Ringing Bells. Bellows, Organ, see Organ Bellows. Blacksmith's Fires. Where a compressed-air supply is maintained for operating rock drills or general machinery, and at a pressure of 6 or 7 atmospheres, the air for blow- ing the blacksmith's fire is sometimes taken from the corn- pressed-air pipes. This is a costly way of supplying air at such a light pressure. The power required for com- pressing each cubic foot of free air for the rock drill is probably ten times as great as would be required for the blowing pressure. Blast, Sand, see Sand-blast, A LIST OF THE VARIOUS APPLICATIONS. l8l Block Sig?ial, see Switch and Signal Service. Bessemer Process, see Aerating Molten Metal. Boiler-shop. Compressed air is now capable of supply- ing all the power required for operating boiler-shops, ma- chines or apparatus, mostly portable, being provided for all of the operations involved. Hoisting, punching, shearing, drilling, tapping, reaming, riveting, chipping, caulking, and screwing in and cutting off stay-bolts are all quickly, effi- ciently, and economically done by compressed air. Brake, Air, see Air-brake. Bridge-building. Compressed air is a valuable assistant in bridge-building, both in the preparation of the material in the shop and in the erection of the structure. In the shop the air is used for hoisting and in portable tools for drilling, reaming, riveting, chipping, etc., as in the boiler- shop. The erection of the bridge would be in many cases impossible without the compressed air in the caissons for the piers, while in the work of erection the portable tools are called in again. Caisson. The caisson is used principally for excavations under water, and subsequently for building, in place of the material removed, bridge piers, or solid masonry for any purpose. The caisson is essentially an open box, of a shape corresponding to the purpose desired, closed at the top and loaded above until it sinks where the work is to be done. The caisson being open at the bottom, the water is excluded by the maintenance of an air pressure within, the pressure increasing with the submergence until at a depth of 80 or 100 feet the limit of human endurance is reached. Men and material pass into and out of the caisson by means of the air-lock. The men within the caisson remove the material with which the lower edge of the caisson comes in contact 1 82 COMPRESSED AIR. until a satisfactory foundation is reached, and the caisson is then built up full of substantial masonry and allowed to remain as a part of the permanent structure, which is con- tinued above it to any height desired. The caisson is now also frequently used in obtaining suitable foundations and supports for the tall and heavy office buildings erected in our large cities. Caissons, Expelling Soft Material from. This is a use of compressed air entirely distinct from its primal function in the caisson of excluding the water so that the men may be able to work in it. When any soft material is found in the progress of the excavation, it is now customary to expel it through a pipe carried up through the top or side of the caisson, the pressure of the air within supplying all the power required. The pipe is provided with a quick-closing valve, so that when the material has all run out the air may not escape. Caissons, Operating Air-lock Doors, see Air-lock Doors. Cars, Propelling, on Street Railways. Compressed air is not yet extensively used for this purpose in the United States, but is permanently established and successful in Paris and elsewhere in Europe. Experimental cars in the United States show excellent results, and the general adop- tion of the system in the near future is more than probable. In cost of plant, in facility of introduction, in economy of operation, and in the entire absence of objectionable feat- ures the compressed-air system surpasses all others. The principal delay as to its extensive introduction is in deter- mining the ultimately best of many details of construction and operation. Cars, Dumping. Cars dumped by compressed air are used in handling earthwork in railroad construction and A LIST OF THE VARIOUS APPLICATIONS, 183 similar service, also for coal, ore, limestone, etc. An air- cylinder and piston under the car dumps the load upon either side as may be desired. An entire working train may be dumped at once, or a man may dump each car separately. Cars, Loading. One of the functions of the air-hoist or of the pneumatic crane. Cars, Unloading. Unloading by lifting the load from the car by the air-hoist instead of by dumping. Oil-tank cars are discharged to a higher level by air pressure ad- mitted to the tank. Car Roofs, Sanding, see Sanding Car Roofs. Cars, Cleaning. This system is now generally used at railroad termini. A supply of compressed air is main- tained, and a hose is led into the car or coach to be cleaned, with a nozzle for discharging the air and a cock for regu- lating or shutting it off. The jet of air is successively passed over the various parts of the interior of the car and the dust and other loose material is driven off at once. Car Seats, Cleaning. The seats and cushions, rugs, etc. are removed from the car and, supported upon wooden horses, are thoroughly and quickly cleaned by the air jet. Car Sills, Pulling Down, see Pulling Down Jacks. Car Wheels and Axles, Removing, see Removing Car Wheels and Axles. Carriages, Gun, see Gun-carriages. Carpets, Cleaning. The patented arrangement of the writer consists of a grated or perforated level floor or an inclined or vertical surface upon or against which the carpet to be cleaned is spread. The carpet is then tra- versed by an air-delivery pipe upon wheels and with handles like a lawn-mower. A hose conveys the air to the delivery- 184 COMPRESSED AIR. pipe and it emerges in a series of fine jets close to tne sur- face of the carpet, rapidly expelling the dust and dirt. An exhaust fan draws the dust away whether liberated above or below the carpet. Castings, Chipping. One of the adaptations of the pneu- matic tool, which see. Caulking. Now generally done by compressed air, espe- cially in boiler- and tank-work and upon the seams and joints of steel ships. This is another of the uses of the pneumatic tool. Cash-carriers. Generally used in the large retail stores. Canal Locks or Lifts. An important invention, lifting vessels to any height by a single lift, one air-lift taking the place of several of the old style of locks. As the lift is balanced, but little power is required to operate and little water is lost. Channelling-machines. A modification of or more elabo- rate application of the rock drill, applied either to getting out stone of required shape and dimensions from its native bed, or cutting smooth channels in the solid rock, as at the Chicago Drainage Canal. Chemical Works. In chemical works a supply of com- pressed air is constantly maintained and employed for various uses, such as the pneumatic pump or ejector, the air-lift and aerating processes. Cleaning. Compressed air is employed in cleaning vari- ous things, such as flues, carpets, castings, by widely dif- ferent apparatus and processes. Chipping. Another of the applications of the pneumatic tool, especially used in boiler-work, bridge- and ship-work, structural ironwork, foundries, etc. Clipping Horses. A LIST OF THE VARIOUS APPLICATIONS. 185 Clocks, Operating. In extensive use in Paris. Almost the only service rendered by compressed air that could be done as well or better by electricity. Coal Drills, Operating. These are revolving drills or augers boring holes very rapidly for light charges of ex- plosives. Coal-mining Machines. The cutting tool of the ma- chine reciprocates like a rock drill. It is mounted upon wheels and cuts under the seam of coal to a horizontal depth of five or six feet, when the coal may be broken down and removed. Coal or Culm Conveyors. Colors, Spraying. Used in silk factories for spraying colors upon silk or satin ribbons. A recently perfected process sprays colors upon pottery, sometimes in liquid form and sometimes as a powder. Varied and novel effects are produced by applying several colors simultaneously by separate jets, or color and glazing may be mixed and sprayed together. Conductor's Train Signal. Extensively used upon the best railroads. Cooling. This is one of the general and widely appli- cable uses of compressed air. The fall of temperature in compressed air upon release is used for cooling drinking- water, for cooling houses or apartments, theatres, for gen- eral refrigeration, ice factories, and cold-storage warehouses. Copying-presses. Couplings, Applying, to Hose. Cranes. Swinging, jib, or travelling cranes. Crossings, Gates at, see Gates at Railroad Crossings. Cupolas, Raising Stock to. Cutting off Stay-bolts. This is done by a special style of 1 86 COMPRESSED AIR. portable shears, requiring no skilled labor, and does not loosen the stay-bolt. Cuts and Quat ries, Driving Machinery in. Dampening Laundry-work. The spraying-jet takes the place of the Chinaman's mouth, said to be employed for the same purpose. Dense-air Refrigerating Process. Used upon warships and elsewhere. The same air is used over and over, com- pressed to say 15 atmospheres and expanded to say 5 atmos- pheres, and the same refrigerative effect is accomplished by less power and in smaller compass than when lower pressures are employed. Direct-acting Hoist. Quicker and simpler than any other. Disappearing Gun-carriage. Disposal of Seivage. The Shone ejector automatically raises the sewage to give it head to flow where the requisite grade cannot be maintained in the sewer. Distributing Sand on Locomotives. Advantage is taken of the air-supply for the brakes, and the tracks are sanded, giving better adhesion and with less waste of sand. Diving-bell. Diving- armor. Doors, Furnace, Raising and Lowering. Doors, Air-lock Doors, Operating. Doors, Opening, in Offices and Residences. This is a sug- gested rather than an accomplished use of compressed air, but perfectly feasible where the air-supply exists. As we now automatically close our doors, so may we open them in welcome when any one approaches. Drainage Systems. Compressed air is variously employed in such service the conditions determining the arrangement. Dredging. A LIST OF THE VARIOUS APPLICATIONS. 1 87 Drills. Revolving drills of various kinds, portable drills, metal drills, coal drills, diamond drills for prospecting. Drills, Rock. Reciprocating or percussion drills. The use of compressed air employing more of it than any other. Drinking water, Cooling. Drinking-water, Aerating. Driving Stay-bolt Tops. One of the special uses of com- pressed air in the boiler-shop, simple, but saving much time and labor. Driving Machinery in Shops. Two or three shops use compressed air for driving all their tools, dispensing with all shafting except a light line for a group of small tools. Driving Pumps. An undeveloped use of compressed air of great importance and promise, see Chapter XVI. Driving Motors or Air-engines. Drop Pits. This is the technical name for an arrange- ment in use in railroad repair shops. The car is run over the pit and an air-jack or hoist lowers wheels and axles to be removed or hoists new ones in place. Droppers for Cattle. This name is given to one series of air-hoists used in the Armour packing-house and similar establishments. The bullock, suspended by the heels, after bleeding and decapitation is conveyed by a continuously travelling overhead railway to a hook on one of the drop- pers, the hook being held up by the pressure of the air with sufficient force to sustain the weight. Upon releasing the air the bullock is dropped upon the floor for skinning, dis- embowelling and such interesting operations. Drop Weight for Breaking Castings, Lifting. A popular use of compressed air in the yards of foundries that are fully equipped with it. A single hoisting cylinder is used 1 88 COMPRESSED AIR. with multiplying sheaves so that the hoist of the weight is usually six or eight times the travel of the piston. Dry Dock. The compressed-air dry dock may have all the advantages of the independent floating dock at less first cost and less cost of operation and maintenance. Dumping Cars. Dynamite Gun. The only safe way yet devised for throwing the high explosives. Decided to be of value for coast defence. A number of these guns now under con- struction. Eggs, Beating. Elevators. Compressed air adapts itself readily to all the various demands of elevator service, and is used for passen- gers or freight, by direct or multiple lift of a single piston, or with an air-motor with gearing and drums. Elevators, Coal and Culm. Elevators, Indicators on. Indicators operated by com- pressed air to signal or to inform the passenger and the operator. Ejector. Used for automatically transferring sewage or other liquids. The air pressure being maintained, the chamber is alternately filled by the flow of the liquid, and emptied by its ejection or expulsion to a higher level. Engines, Fire, see Fire-engines. Engine Works, Driving. Expelling Soft Material from Caissons. Extinguishers, Automatic Fire. Factories, General Use in. A great and rapidly increas- ing number of factories are equipped with compressed air, first of all for direct hoisting, and subsequently for various other purposes. Finish, Satin, on Metal-work, see Satin Finish. A LIST OF THE VARIOUS APPLICATIONS. 189 Filtering Water. Fire-engines. A suggested use of compressed air, per- fectly feasible wherever a general supply of compressed air is distributed. Fire-extinguisher. Fires, Blacksmiths', Blowing. Fires, Kindling. The aerated oil jet is used in many round-houses for starting the fires in the locomotives at one tenth of the cost of wood kindlings. Flues, Cleaning. Forcing Oil. Transferring oil from tanks to barrels, or vice versa. Foundry, General Service in. Fountains, Cooling, see Chapter XIII. Furnace Doors, Raising and Lowering. Gas, Aerating. Gates at Crossings, Operating. In connection with the compressed-air switch and signal service. Gear Steering, on Ships. General Hoisting Service. Some establishments employ- ing more than a hundred air-hoists. Glass Factories. Glass-blowing. Grain Elevators. Granite-carving. Granite-cutting. One of the uses of the pneumatic tool. Grates, Shaking. Gun carriage, Disappearing. Gun, Pneumatic. Valuable for coast defence, throwing high explosives. Guns, Sporting or Target. Hammer, Pneumatic. COMPRESSED AIR. Hardie Car-motor. Hoisting Cattle, Beef. Air-hoists used exclusively in the largest packing-houses. Hoist, Direct-acting Vertical-cylinder. Hoist, Geared. Horses, Clipping. Hose couplings, Applying. The machine for this purpose is said to have paid for itself in one day's application of it. Hydraulic Cranes. Air is used to give pressure to the water, while the water actually does the hoisting in some lines of service where the elasticity of the air would be objectionable. Hydraulic Pressure Relief. In wood-pulp machines in paper-mills a hydraulic feed is employed which is some- times too positive, and a chamber of compressed air is pro- vided to relieve it and prevent breakage. Ice-making. Indicators on Elevators. Iron, Drills for. Iron Furnaces, Tapping, Iron Bridge Work. Ironwork, Structural. Jacks, Portable. Jacks, "Pulling Down." Kindling Fires in Locomotives. Lamps. Aerated oil lamps for street work, railroad op- erations, etc. Lard- refining. Laundry-work, Dampening. Lifting Drop Weight in Foundry Yards. Locks, Canal. Lock Doors in Caissons, Operating. A LIST OF THE VARIOUS APPLICATIONS. IQI Loading Cars. Locomotives in Mines, Street Railways, etc. Locomotives, Kindling Fires in. Medical Preparations, Spraying. Mekarski System of Car Propulsion. Mining Coal. Compressed air is variously used in coal mines, for " coal-cutters," coal augers, rock drills, pumps, hoists, etc. Mixing Nitroglycerine. Moulding-machines. In the foundry compressed air rams or presses the sand in the moulding-machine, lifts the mould, draws the pattern, etc. Nitroglycerine, Mixing. Operating Air-drills and Punches Opening Doors. Packages, Transmitting. Painting. Pile-driver. Pits, Drop, see Drop Pits. Physicians' Spraying Apparatus. Pneumatic Ejector. Pneumatic Press. Pneumatic Signal for Railway Trains. Pneumatic Tool. Pneumatic Tubes for Transmission. Portable Drill. Portable Jack. Preserving Timber, the Wood Vulcanizing Process, which see. Press, Copying. Press, Straightening. Pottery, Spraying with Colors* IQ 2 COMPRESSED AIR. Process, Bessemer, see Aerating Molten Metal. Pulling Down Jacks, see Jacks, Pulling Down. Pump, Air-Lift. Pump, Automatic. Pump, Beer. Punips, Operating. Pumping Acids. Punch, Portable. Punching in Boiler-shops, etc. Quarries, General Work in. Railways, Street. Railroad Shops, Various Uses in. Railroad Shops and Sheds, Whitewashing. Raising Stock to Cupolas in Foundries. Raising Ships. Air-tight bags are attached all around a sunken ship, or placed by divers in the hold, then inflated by compressed air, and, acting like balloons in the air, when their combined displacement is sufficient the ship rises. Refining Lard. Refining Asphalt. Refrigerating. Removing Mandrels. Removing Scale from Steel Plates another of the uses of the pneumatic tool. Ribbons, Spraying with Colors. Ringing Bells on Locomotives. Riveting. Rock Drills, Operating. Rock Tunnels, Driving, All Operations in. Sand-blast, A LIST OF THE VARIOUS APPLICATIONS. 1 93 Sanding Tracks. Giving better distribution, better adhe- sion, and wasting less sarid than where delivered by gravity. Sanding Car Roofs. A process used in the car-building or repair shops in connection with the painting of the roofs of freight cars. The sand is delivered by the air with force, so that it embeds itself in the paint, forming a. protection for the surface. What is not held by the paint is removed by the same blast of air that delivers the sand. Satin Finish on Metals. Used on plated work for rail- road cars. Scale, Removing, from Steel Plates. Seats, Cleaning. Sewage Disposal. Sheathing Pile-driver. Sheep-shearing. Ships, Raising. Ships, Steering. Ships, General Service on. Shops, Driving Machine Tools in. Signal, Block. Signal, Conductor's. Silk Manufacture. Silk Ribbons, Spraying. Skates. Soft-ground Tunnels. Spraying Laundry-work. Spraying Colors on Silk Ribbons. Spraying Colors on Pottery. Stay-bolts, Cutting off. Stay-bolt Taps, Driving. Steering-gear on Ships. Stone-cutting. 194 COMPRESSED AIR. Storage, Cold. Steel Plates, Removing Scale from. Street Railways. Structural Ironwork. Switches and Signals on Railroads. Syrups, Agitating. Taps, Driving, in Boiler-shops. Tapping Iron Furnaces. Testing Brakes. Timber, Preserving. Tires for Vehicles. Tool, Pneumatic. Torpedo Service. Tracks, Sanding. Train Signal. Transferring Oil or Acids. Transmitting Packages. Transmitting Power from Waterfalls. Travelling-crane. Trucks, Dumping. Tunnels, Soft-ground. Tunnels in Rock, Turrets, Operating on Warships. Unloading Cars. This is done either by hoisting, by dumping, or in tank cars by pressure upon the service of the liquid. Ventilating. Vertical Direct Hoist, Vehicle Wheel-tires. Warfare, General use in. Water-balloon, see Raising Ships, Water, Raising. A LIST OF THE VAktOUS APPLICATIONS. 1 9$ Water, Aerating. Water, Filtering. Wheels and Axles, Hoisting or Removing. Whitewash ing. Working Turrets. World's Fair Painting. Wood Vulcanizing. Works, Chemical, General use in. INDEX. Absolute temperature, n. Absolutely isothermal or adiabatic compression impossible, 22. Accommodating attitude of air, 138. Action of air in passages of two-stage compressor, 75. Actual curve in expansion always above theoretical adiabatic, 102. Actual volume of air the basis in transmission computations, no. Additional lines on indicator-diagram, 43. Adiabatic and isothermal curves not required for computations, 51. Adiabatic compression, 15. Adiabatic curves to draw on diagram, 49. Advances in steam economy, 38. Air-brake pump, 128. Air-compression line simpler than the steam-expansion line, 49. Air-compressor as an air-meter, 54. Air-compressor is its own dynamometer, 39. Air-compressor diagram, 129. Air a political factor, 140. Air always contains moisture, 148. Air hoisting, 137. Air for operating pumps, 138. Air never freezes. 147. Air quickly heated or cooled, 95. Air readily receives or imparts heat, 63. Air the natural power-transmitter for mines, 175. Air used without cooling or draining, 150. Alternate resistance in single-acting two-stage tandem compressor, 83. Applications of air-compression diagram, 100. Back pressure in two-stage compression, 77. Bad luck of compressed air, 138. 197 19 INDEX. Bad practices of pipe-fitters, 114. Bad record of air for pumping and its causes, 169. Beginning of economical compression, 53. Best air-compressor practice, 31. Boiling-point variable, n. Capacity of air for water, 149. Capacity of compressor as reduced by clearance, 60. Catalogues as diffusers of misinformation, 3 Caution as to use of compression table, 23. Cold as possible air for compression, 54. Cold-water fountains, 144. Common working pressure for air, 70. Complicated operation of compression, 75. Compound compression, 25. Compressed-air diagram, explanation of, 16. Compressed air gives less power than equal volume of steam, 98. Compressed-air problem (the), 27. Compressed-air literature, 3. Compressed-air transmission, no. Compressed air versus electricity, 135. Compressed air widely used without freezing up, 148. Compressing cylinder always the first, 72. Compression completed in first cylinder of two-stage compressor. 72. Compression in a single cylinder, 61. Compression-line of air and steam expansion-line, 49. Compressors for continuous service, 134. Compressors in general use, 61. Computing M. E. R., 44. Computing I. H. P., 46. Computing power cost of compression, 90. Computing power required for compression, 23. Condition of interior of pipes, 113. Conditions of highest economy in compression, 134. Considerations of economy inapplicable, 4. Constant readiness of air, 137. Constant work under best conditions, 133. Continued transmission in winter, 154. Cooling air for caisson work, 156. Cooling drinking-water, 144. Cooling by injection, 67. Cooling by water-jacket, 64. INDEX. 199 Cooling of air at release, 33. Corliss compressor, 133. Corliss feature for selling rather than for operating, 133. Cost of air-volume when produced by reheating, 158. Cost of compression only one part of question of economy, go. Definitions and general information, 9. Devices for equalizing pressure to resistance, 130. Diagram from first cylinder does not vary with ultimate" pressure, 72. Diagram for one volume of steam and air expanded, 99. Diagram for drawing adiabatic curve, 49. Diagram for drawing isothermal curve, 48. Diagram of steam and air expanded to one atmosphere, 101. Diagram of theoretical air-compression, 27. Diagram of practical air-compression, 29. Diagram of good comparison, 68. Diagram of volumes after reheating, 164. Diagram of pressures after reheating, 165. Diagram of volumetric relations of air and water, 142. Diagram showing no cooling of air in early part of stroke, 65. Diagrams from air-brake pump, 129. Diagrams from novel air-compressor, 132. Diagrams in compressor catalogues, 127. Diagrams of two-stage compression in single-acting cylinders, 71. Diagrams combined for double-acting cylinders, 84. Difference between diagrams from air and steam cylinders, 40. Difference between theoretical and actual temperatures, 26. Difference between theory and practice, 28. Differences in free-air volumes due to temperature, 55. Different effects of heat upon air and water, 141. Difficulty of learning the truth of air-compression practice, 126. Distinct operations in air-compression (two), 24. Distributing pipes, in. Distribution of air in relation to intercooler, 85. Drawing the adiabatic curve, 49. Drawing the isothermal curve, 48. Drinking-fountains with warm water, 144. Dry air from injection compressors, 152. Dry-goods box and tumbler, 142. Economical compression, 53. Effect of heat on compressed air, 14. Effect of intercooler, 85. 2OO INDEX. Effect realized in mining-pumps, 36. Efficiencies in use of air, 33. Electric brake, 137. Electricity generally inapplicable for the work that compressed air does, 136. Electricity on railroads, 139. Entrained water in air-meters, 151. Erroneous ideas as to losses in transmission, in. Example of pumping by air, 169. Examples of use of formula for flow of air, 117-119. Explanation of compressed-air diagram, 16. Explanation of general compression table, 20. Explanation of practical compression diagram, 30. Expansion of air by heat cheaper than steam production, 157. Factors in transmission computations, 112. Fahrenheit scale, 11. False position accepted by compressed air, Five C's (the), 133. Fly-wheels on compressors, 130. Formula for friction of air in pipes, 115. Fountain cooled by compressed air, 144. Four sources of loss in air-compression, 93. Free air, definition, 10. Free air the raw material of compression, 54. Freezing up most frequent with low pressures, 155. Freezing up of air-motors, 34. Friction of engine, 39. Friction in straight-line compressors, 94. Gas-engine, 135. General Compressed Air Company, Where ? 2. General compressed-air service, 145. Getting the air not only at but into the cylinder, 56. Giving a dog a bad name, 2. Governing the compressor, 134. Graphical study of two-stage compression, 81. Great changes of temperature with small transfers of heat, 143. Growing demand for compressed air, 6. Heat not evenly distributed in cylinder parts, 66. Heat mostly abstracted in latter part of stroke, 64. Heating and cooling of compressor parts, 63. Heating ceases when compression ceases, 65. INDEX. 201 Heating effect of compression, 15. High-pressure air and dry air, 155. High pressures and pressure-reducers, 156. How not to do it, 35. Importance of the unimportant, 114. Indicator-diagram must not be taken too early, 41. Indicator does not tell weight of air compressed, 57. Indicator on the air-compressor (the), 38. Indicator peculiarly applied to air-compressor, 39. Intercooler, 86. Isothermal compression, 15. Isothermal curve, to draw, 48. Keeping the air cool means actual cooling, 62. Large compressors for continuous service, 134. Less than nothing to do, 82. Limits to reheating, 161. List of applications of air, 176. Little competition between air and electricity, 135. Little heat for reheating air, 157. Little power lost by clearance, 60. Little storage of air possible, 135. Loss, the word misleading, 36. Loss by elbows, 114. Loss by friction in two-stage compression, 80. Loss in compression not necessarily final, 31. Loss in transmission, 32. Loss in transmission not due to friction, 160. Loss of pressure compensated for by increase of volume, 32. Losses by hot free air, 57. Losses less in air-transmission than with any other transmitter, III. Low friction in Corliss compressors, 94. M. E. R. for compression lower than for delivery, 73. M. E. R. different in single and in two-stage compression, 74. M. E. R. for compression only, 24. M. E. R. for whole stroke, 22. M. E. I^r. single and two-stage compound, 76. Measurl?g clearance, 44. Measuring total volume compressed, 44, 47. Mechanical versus commercial economy, i. More air-pressure behind piston than in front, 82. Much air to cool a little water, 145. 202 INDEX, Novel arrangement for equalizing pressures, 130. Obstructions in pipes, 114. Oil-engine, 136. Operating pumps, 138. Operation of intercooler, 86. Paradox in use of air, 102. Peculiar position of compressed air, 2. Pipe conveying air to compressor, 55. Pohle air lift-pump, 143. Postal transmission, 5. Power cost of air, 90. Power required for hoisting and pumping, 167. Power value of air, 98. Practical man has no use for small figures, 55. Pumping a field for comparison with electricity, 174. Pumping should show high efficiency, 168. Rapid cooling of air in pipes, 143. Ratio of cylinders, 71. Reading the compression-diagram, 38. Receiver near compressor does not dry the air, 151. Receiver needed after air is cooled, 152. Reheating, 34/157. Reheating generally impracticable, 163. Reheating in Paris, 163. Reheating is doing work over again, 159. Relation of volume to temperature, n. Relative work of low- and high-pressure cylinderr. ~ Ready-made pumps, 172. Rock-drill and air-compressor (the), 167. Saving by reheating, 34. Simultaneous heating and cooling, 63 Single-acting tandem two-stage compressors, 77. Single cylinders mostly used, 70. Size of compression-cylinders, 69. Small compressors as missionaries, 8- Specific heat of air and of water, 14. Starting business under favorab e conditions, 62. Steam-pressures guarantee temperatures, 57. Steam-pumps, 169, 171. Summary of relations, 12. Table of weights and volumes of dry air, 13. INDEX. 2O3 Table of volumes, mean pressures, etc., 19. Table of final temperatures, 37. Table of absolute pressures, boiling-points, etc., 52. Table of power required to compress air, 92. Table of mean effective and terminal pressures, 103-108. Table of volumes of air flowing in pipes, 109. Table of relative volumes of air at different pressures, 119. Table of head required to overcome friction in pipes, 121-125. Temperature of air in cylinder not ascertainable, 58. Thermal relations of air and water, 141. Theoretical compression, 28. Transmission formulas unsatisfactory, 112. Triumph of the steam-engineer in electrical developments, 139. Tumbler and the dry-goods box, 142. Two-stage compression, 31, 70. Two-stage compression in single-acting cylinders, 71. Two things combine to cause freezing up, 148. Unique among power-transmitters, 5. Unique opportunity of electricity, 170. Unit of heat, 14. Ultimate economy in reheating, 162. Up-to-date compressor (the), 126. Use of air for old steam pumps, 35. Use of air in railroad shops, 7. Use of table of power cost, 93. Various efficiencies in use of air, 33. Various ratios of the four losses in compression, 97. Vindication of air-brake pump, 128. Warm air in blowing cylinders, 59. Water in compression-cylinders and lubrication, 67. Water-jacket, 64. Water will not wet what is wet, 153. Wastefulness of air-brake pump, 4. Wet compressor furnishes driest air, 153. Whitewashing apparatus, 6. Without loss or gain of heat, 15. Worst air-compressor in existence, OF THE UNIVERSITY THIS BOOK IS DUE ON THE LAST DATE STAMPED BELOW AN INITIAL FINE OF 25 CENTS WILL BE ASSESSED FOR FAILURE TO RETURN THIS BOOK ON THE DATE DUE. THE PENALTY WILL INCREASE TO SO CENTS ON THE FOURTH DAY AND TO $l.OO ON THE SEVENTH DAY OVERDUE. LD2