LIBRARY HANDBOOK, No. MENDING AND REPAIR OF BOOKS COMPILED BY MARGARET WRIGHT BROWN THIRD EDITION REVISED BY GERTRUDE STILES Supervisor of Binding, Cleveland Public Library AMERICAN LIBRARY ASSOCIATION PUBLISHING BOARD C ; : GAGO ' 9 : I - MENDING AND REPAIR OF BOOKS LIBRARY HANDBOOK, No. 6 MENDING AND REPAIR OF BOOKS COMPILED BY MARGARET WRIGHT BROWN THIRD EDITION REVISED BY GERTRUDE STILES Supervisor of Binding, Cleveland Public Library AMERICAN LIBRARY ASSOCIATION PUBLISHING BOARD % CHICAGO 1916 CONTENTS PAGE INTRODUCTORY XOTE 7 WHEN TO BIND OR WHEN TO MEND 9 THE MENDING TABLE: ITS SUPPLIES 12 PASTE, THE MENDING MEDIUM 13 WAYS TO MEND 14 WAYS TO CLEAN 20 BINDING RECORD 22 TEMPORARY BINDERS 23 348049 INTRODUCTORY NOTE THE task of mending demands so much of the time and energy of library workers and is a factor of such eco- nomic importance in every public library that it cannot be put aside as incidental. It is hoped that these suggestions may give definite aid in this homely task which is ever present in all libraries. No attempt has been made to give instruction in the advanced processes of mending, as this at once encroaches on the art of binding. The best mending can be done only where an acquaintance with the construction of the book has been acquired through a study of the various processes of binding. Librarians are urged to visit binderies to see the various processes; and to study the art of binding under personal instruction of experi- enced binders whenever this is feasible. It is not probable that any one librarian will use all of the processes suggested, and some of these will apply only to exceptional cases; but the directions cover diversified condi- tions in order that the librarian may have the necessary information whenever required. The experienced mender. This handbook has not been prepared for the use of the larger libraries where a bindery is a part of the equipment, or where there are on the staff those trained in binding and hence experienced menders. The inexperienced mender. The purpose of this handbook is to give practical aid and guidance to librarians who are entirely inexperienced in the work of mending and repair of books and whose knowledge must be gained through self- instruction. The compilers have drawn upon many sources and have endeavored to make available the suggestions received and methods used by many librarians and practical binders, and grateful acknowledgment is herewith made for the co-opera- tion and helpful suggestions received from them. MENDING AND REPAIR OF BOOKS WHEN TO BIND OR WHEN TO MEND THE question when to bind or when to mend is of daily recurrence, and a decision must be made upon the examination of every circulating book returned, before placing it on the shelves. The answer will depend largely on the policy of the library regarding the binding question. No library can afford to circulate shabby, soiled or ragged books, because: (1) From an economic standpoint, a Jbooks' ultimate usefulness, or life, is materially shortene'd by neglect to bind at first sign of need. (2) When books are given proper care by the library, standards are set which insure a like treatment on the part of the reading public. (3) The reading public has a right to expect that its books shall be clean and whole, and that its prop- erty shall be in proper condition for satisfactory use. WHEN TO BIND When the stitches break and a section or a few leaves fall out, the book should be sent to the bindery immediately. This is happening daily with the original publish- ers' bindings. If the book is removed from the shelves the librarian is at once confronted by the problem of being unable to answer the unceasing cry for the last new novel, as it is the fiction which is usually in this condition. However, if the book is allowed to circulate a few more times there are "pages missing" and the book has become valueless. No book should be rebound with pages missing. 10 MENDING OF BOOKS When the stitches have not broken, but either a few or all the sections have become loose: There is no excuse for the librarian to leave upon her shelves or permit to circulate books that are held together only by the slender threads with which they are sewed and threatening at any moment to come tumbling forth from the cover. Such books speak in no uncertain terms for rebinding or permanent withdrawal from the shelves. Shall books be sent to the bindery when in greatest demand? YES, when they cannot be circulated further without per- manent injury to them. Such books should be hastened through the bindery by statement to binder regarding immediate need. If your present binder cannot bind promptly, find one who will. A month is a reasonable time. The prompt rebinding of a book more than doubles its life. If the book has been reinfoiced at first sign of giving way (see page 17) all the temporary assistance that can safely be given has been rendered and if the book is of permanent value to the library it must be rebound. WHEN TO MEND When the stitches are not broken or loosened, and still hold sections firmly together. When the joints are loose. When the book has once been rebound. The tendency among librarians is to mend too much be- fore rebinding. Mending makes rebinding more difficult and jeopardizes the life of the book. It is only in rare cases, such as the fact that a book is out of print, and yet valuable to the library, that a second rebinding is justified. MENDING- OF BOOKS 11 WHEN TO REPLACE Will it 6e cheaper to mend a look and, when its short life is done, withdraw and replace with a new copy? YES, when the original cost is less than rebinding. NOTE In the decision to replace, the labor of acces- sioning and withdrawal must always be taken into account. The fresh, clean copies of the "easy books" and other good, inexpensive juvenile books are to be pre- ferred to rebound copies. If the original binding is so poor that a second copy would shortly be in the same condition as the first, it is then advisable to send the book promptly to the bindery for recasing, preferably before circulating. Greater durability is thus insured. If the book has an attractive original cover it is pre- served and the value of the book enhanced thereby. YES, when the paper is of such poor quality that the leaves break away from the stitching. YES, when the book is extremely soiled; replace, even if it costs more than rebinding. YES, when a new edition, or better books on the same sub- ject have been published. In replacing fiction, inexpensive editions are available for many popular titles in the Grqsset & Dunlap edition, Burt Home Library, Everyman's Library, etc. Some inexpensive editions rebind and wear as well as the first editions. Others because of narrow margins or quality of paper do not pay to rebind. A little observation and experience will soon prove what titles can be rebound to advantage. Special library binding may be obtained for a few titles of fiction and juvenile books, as some publishers are issuing these in binding following the specifications of the A. L. A. Committee on Binding. These cost more than the regular edition but the additional cost repays in increased durability. The publishers give ample notice of new titles that are to be published in this way. In ordering books, it is desirable to give general instructions that the special library binding is desired whenever available. 12 MENDING OF BOOKS THE MENDING TABLE: ITS SUPPLIES A piece of glass or white oil cloth, cut to fit the size of the table, will be found most conducive to cleanliness, as it can be quickly and easily washed. Paste. Library paste, powder form, mixed as needed. Cloth. White outing flannel, cheese cloth and cheap grade of canton flannel, purchased by the yard at any dry goods store. Art Vellum in assorted colors, cut in strips. Cambric cut in strips. Paper. Onion skin bond, cockle finish, 9 Ib. weight. Cut into strips for use; tissue paper. Brushes. Flat, rubber- set photographer's brush, about 1 inch wide; also artist's round bristle y 2 inch thick. Scissors. Slender, six-inch blade, good quality. Knife. Shoemaker's long blade, square at end, or com- mon paring-knife purchased at hardware store. Folder. Bone, 15c, purchased at stationer's. Needles. Milward's Sharps, No. 1, or any strong and not too coarse darning needle. Thread. Hayes' linen, No. 25; Barbour's linen, No. 40. Pressing tins. 6x8 in., obtained at tin shop. Zinc is pleasanter to use and will not rust. Cleansers. Wash for pages; wash for book covers; pow- dered pumice stone; art gum, lOc per cube. Shellac. Consult local druggist or paint dealer regard- ing the best white shellac. Press. An old letter-press can usually be found in the community which may be purchased for a small sum. Prices on new copying press 10 x 12 in. may be ob- tained of local stationer. A local bindery or any binder's supply house will furnish mending materials; also price list and samples of materials may be obtained from the following: Democrat Printing Co., Madison, Wisconsin. Gaylord Bros., Syracuse, New York. MENDING OF BOOKS 13 PASTE, THE MENDING MEDIUM Paste may be used with less danger of injury to the book than glue, and is the only mending medium which should be used on books that are to be rebound. Under no condi- tion should mucilage be used on any book which is to be rebound. Some librarians persist in doing this and then expect the binder to do good work. Glue should never be used except by experienced menders. There are various powdered pastes on the market used by book-binders, bill-posters, paper-hangers and others. Spon Tern or Steko, manufactured by Clark Paper & Twine Co., Rochester, N. Y., and Rex Dry Paste, Geneva, N. Y., are both excellent in adhesive qualities and easily prepared, mix- ing with either hot or cold water and without cooking. If powdered paste is not obtainable a gbod flour paste may be made as follows: RECIPE FOR FLOUR PASTE Mix a thin batter of flour and water, cook and as it thickens add hot water until right consistency and until thor- oughly cooked. It will be well cooked when all milky appear- ance of the flour and water has disappeared and when bubbles of air begin to explode through the mixture. After taking from the fire a preservative may be added if desired, such as a half teaspoonful of oil of wintergreen to a pint of paste. At times it is desirable to do some simple pasting, such as tipping in a single leaf or label, and for such work any good library paste is a great convenience. Use. Paste for small surfaces is more evenly spread with the finger, and there is less waste than with a brush. Spread thinly, using only enough paste to make paper stick securely. Thick paste spreads more smoothly than thin and is not taken up quickly by the paper. This is an im- portant point, for if the paper stretches or expands the work can not be done in a satisfactory way. Provide cheese cloth cut in small pieces for use in rubbing down the pasted parts, and for keeping the fingers clean, etc. These should be used only a few times. Cleanliness and neatness are absolutely essential to good mending. 14 MENDING OF BOOKS WAYS TO MEND Avoid too much mending. Paper used for mending should be cut lengthwise with the grain of the paper. Cloth should be cut the long way of the material. In mending always use paper of lighter weight than the book. For books printed on heavily coated paper, tissue or bond is too light, but paper cut from margins of advertising pages of magazines is a suitable weight. PAGES Torn through the printing may be mended as follows: (1) Use un gummed, transparent mending paper, cutting it the size and shape of the tear, and about one-half inch wide. Apply a thin coat of paste to the strip and fit it carefully over the tear, having first placed a strip of waste paper under the torn leaf to absorb extra paste. (2) For finer or better class of books, upon which more time and care may profitably be spent, rub a very little paste on the torn edges, place torn edges together, then take a rather large piece of ordinary tissue paper and rub it gently along the tear so that the tissue paper will adhere to the torn edges. Put under press, and when dry the superfluous tis- sue paper should be torn off, using care to pull always toward the tear and from both sides at the same time. The delicate fibre of the tissue paper acts as an adhesive and it is almost impossible to discern the way in which the mending has been done. Torn in the margin Use thin, firm mending paper, preferably a tint to match paper of the book. Cut a strip one-half inch wide corresponding to the size and shape of the tear, apply paste and trim even with the edge of the leaf. When these processes are used, place books in press until thoroughly dry. Do not use gummed paper for this work. It makes a dis- colored patch on the pag'e and the mending very apparent. MENDING OF BOOKS 15 LEAVES When loose leaves are replaced the greatest care should be taken to make sure that they do not extend beyond the edge of the book. If this occurs, it shows careless or inex- perienced mending^ Loose leaves may be inserted in several ways: (1) If the leaf fits exactly into the book, it may be tipped in by applying paste to one-eighth inch of its inner margin. Place the loose leaf in the book, the outer edge even with the book, and rub down the pasted inner margin against the next leaf with bone folder. Put the book in press until dry. Illustrations may be tipped-in in this way when it is desirable to preserve them. (2) If it is found by measuring that the leaf when inserted, will extend beyond the edge of the book, fold the leaf at the inner margin over a ruler edge, or other straight edge, slightly more than one-eighth of an inch, thus making a hinge. Apply paste to this hinge with the finger. Place leaf in the book and push well back; rub the little pasted hinge down with bone folder, being careful to leave no free paste. (3) In case the quality of the paper of the leaf to be inserted will not stand the tipping-in process, or is badly worn at the inner margin, it may be inserted by a guard. Fold a half-inch strip of onion skin paper, lengthwise. Apply a thin coat of paste to the outside of this strip. Attach half of the strip to the inner edge of the loose leaf, and the other half to the adjoining page in the book, close in by the fold. Trim edge of leaf if it projects. Put in press until dry. Do not use gummed muslin for this work. It destroys the chance of proper rebinding and detracts from the appear- ance of the rebound book. 16 MENDING OF BOOKS SECTIONS When more than one section, sometimes called signature, is loose in a book which is worth rebinding, it should be rebound at once. When the thread in one section only is broken, or one section only is loose in a rebound book and the rest of the binding is intact, the section should be inserted. To avoid further ravelling, it is necessary to secure the broken threads of the book either by fastening them together, or attaching to new threads; also that the loose section is sewed or tied through the super on the back .of the book. Loose sections may be inserted as follows: If the folds of the leaves in the loose section are torn or thin, they should be mended before replacing the section. Take a half-inch strip of thin, firm paper, the length of the page; fold through the middle length- wise and paste down through the center fold of the leaves. A touch of paste along the fold of each will hold all the sheets together. Open the book at the place where the section is loose. (When the book is open the back of the book separates from the cover.) Open the loose section and place it in the proper position in the book. Near the top and bottom in the center fold of the section will be seen the holes which were made by the binder. Thread a needle with Barbour's linen thread No. 40, or Hayes' linen thread No. 25, and tie new thread to broken end of thread in book. Pass the needle through the hole at the top of the loose section and out between the book and its loose back. Do not pull the thread clear through. Drop the needle and thread down between the back of the book and the loose back to the bottom. Run the needle and thread from the outside in through the hole at the bottom of the loose section. Pass the needle and thread around again in the same way. Draw tight and tie with a hard knot at the point of beginning. MENDING OF BOOKS 17 JOINTS Books in the ordinary case or publishers' binding will, after a short period of use, show signs of weakness in the joints (where the book and cover are attached). The paper cracks and both it and the super on the back of the book loosens and unless immediate attention is given the stitching breaks and the book must go to the bindery. This super is a loosely woven cotton cloth which is glued on the back of books to help hold the sections together, and extends from the back of the book to the inside of the cover to help hold the book and cover together. In the publishers' bindings, this super is usually all that holds a book in the cover. Loose joints may be Reinforced by tightening and stripping. Hold the book open in an upright position on the table. The back will separate in a curve from body of book; with the round brush apply paste between the loose back and the book, along the joints only. If too much paste is used it will spread over the back, causing the cloth cover to become wrinkled and title illegible. Close the book, care being taken to push book well back in cover, and with bone folder rub well along the joints, squeezing out any extra paste at head and foot. Dry under weight for a half-day at least. Then with knife clean off the ragged edges of torn paper along the joint inside the cover. Place the book flat upon the table, the front cover open, take book of similar thickness and place under open cover. Take a strip of cambric or paper. Cut this strip the exact length of the book, and apply thick paste so that the paper or cloth will not stretch. Paste one-half of this strip to the fly-leaf and the other half of the strip on the cover of the book. Make sure that the strip is smoothly laid, not stretched too tightly from book to cover, or it will pull up first pages when book is used; if too loosely stretched it is un- sightly and fails of its purpose; allow the book to remain open until the strip is dry. Repeat this process for the back cover. 18 MENDING OF BOOKS RECASING When the stitching has not broken, and the paper is of good quality a book may be removed entirely from its cover and recased. In recasing, painstaking care is required and books must be in condition specified to obtain satisfactory results. Take a sharp knife and cut through the super at both joints. This super is easily lifted from the inside of the book cover. Pull it off the back of the book, taking great care in this, and remove all particles of dried glue. Take white outing flannel, which is light in weight and double-faced, or canton flannel (downy side towards the book), or cheesecloth. Cut a strip as long as the back of the book and two inches wider; paste this over the back only, allowing an inch extension on each side. Do not, in this first process, put paste on the extensions. Draw the cloth over the rounded edges of the back (or joints) ; rub the back well with bone folder and also over the rounded edges, but do not paste the cloth down beyond the rounded edges. During this process hold the back of the book so that the sections, or signatures, will not separate. After thorough rubbing let dry. Apply paste to inside of book covers one inch next the joints; do not put paste on back of book. Place book in cover, pushing well back, making sure that it is correctly placed. Paste down the one-inch extension of cloth, laying waste paper between it and book; close book, rub joints well with bone folder and allow to dry thoroughly. Strip joints, following instructions for re-inforcing; paste clean paper lining on book covers, press and dry. The book should then be opened as carefully as a new book. PRESSING This adds greatly to the appearance of the mended or repaired books. Do not place weights over the rounded back of a book. Place the pressing boards or tins over the covers of the book only, even with, but not extending over, the joints. Pressure on the rounded back will weaken a book in the most vital part. MENDING OF BOOKS 19 MISSING PAGES When a page is missing and it is impossible to replace the book with a new copy, the page may be typewritten and tipped in. When it is necessary to rebind the book, the margin of the typewritten page should be left an inch wider on each side than the regular margin. This is for the convenience of the binder, who will trim down the margin in process of re-binding. Make typewritten page conform to size and shape of printed page. NOTATION FOR DAMAGES When there is an injury to a book which is allowed to remain in circulation, the reading public should be made aware that the damage is known to the library by a nota- tion, with date, near the injury, e.g., "Damage noted 1 Mr. '16, Free Public Library." 20 MENDING OF BOOKS WAYS TO CLEAN The book should be cleaned as well as mended. Too much attention cannot be given to the cleanliness of the books in circulation. There is nothing that more quickly creates a distaste for the use of a public library than the handling of soiled and grimy books. Careful study of the paper upon which books are printed is necessary, and in cleaning the fact that different papers and finishes require different treatment must be taken into account. The spongy feather-weight paper upon which much of the fiction is printed is difficult to clean. Pencil marks may be erased with art gum used gently; soil of any other kind is almost impossible to remove. Heavily cleay-coated paper may be cleaned with powdered pumice or a hard eraser. Highly calendared paper and any hand made paper may be cleaned with a damp cloth; cleaning but a few pages at a time and allowing book to remain open until dry. PAGES Soiled pages may be cleaned in the following ways: With art gum, rub gently and slowly, holding the page flat with the left hand to prevent tearing. With powdered pumice stone, rub on with a clean cloth. With damp cloth, be careful that cloth is not too wet. Rub always from inner margin of the page outward, to prevent crumpling. Brush off carefully all particles of rubber, or pumice stone, allowing! none to remain in the folds between the leaves. Mud stains may be removed by using a soft brush or sponge, with a preparation of the following proportions: One cup water, one teaspoon ammonia, four drops carbolic acid. Avoid too much rubbing or print will blur. Slip the pressing tin under the page, and after washing, place white blotting paper on each side of the leaf. Ink stains may be removed by one of the standard ink eradicators to be obtained of local stationer or druggist. Edges of the leaves may be cleaned by sandpapering, hold- ing the leaves of the book very firmly together, or putting book into press. MENDING OF BOOKS 21 COVERS Soiled covers may be cleaned by using a hard eraser, pumice stone or soap and water. The best results are obtained by the use of the following wash: Two parts good vinegar and one part water. Apply with a clean cloth and rub hard until dirt is removed, then place upright to dry. This should not be used on leather. The book should then be shellacked. Shellacked covers. New books may receive preliminary care by shellacking before placing in circulation. Shellacking the covers, especially those in light colors, provides great protection from dirt, and they are then easily washed with the vinegar and water. Another coat of shellac is advisable after washing. To .shellac, hold the book by the printed matter and apply the shellac, which may be diluted with a little wood alcohol, taking care to shellac the edges well. Give two coats; between^ coats suspend on a cord over night to dry. After the last coat, rub with soft cloth slightly oiled with olive oil. This prevents sticking. If the books are labeled before shellacking, the ink must be allowed to dry thoroughly or it may run; in removing the labels, use wood alcohol first to cut the shellac and then soak off with blotting paper and water. Care should be taken in the selection of the shellac; if not, the books will be gummy and hard. The leather on bound magazines and books often becomes very dry and will split and crack.. This is especially true of books not greatly used, as the oil of the hands acts as a great preservative. To prevent this cracking and splitting, some oil is necessary. Vaseline is good for this, applied with a cotton pad covered with a soft cloth, and should remain on the leather for a day to permit absorption of the oil. Some leathers will absorb a second application, after which books may be rubbed down and returned to shelves. The oil or vaseline does not harm the gilding. This may be done once a year, depending upon the condition of heat in library and upon age and condition of leather bound books. 22 MENDING OF BOOKS Worn covers may be replaced on books with leather backs by removing cloth from the boards dry, and using this as a pattern from which to cut new cloth or paper. Reline inside of boards with paper. Covers split at joint. Strips of cloth in assorted colors may be obtained with other mending supplies to reinforce covers split at the joints. This cloth may be obtained gummed or ungummed; if ungummed, use glue; if gummed, moisten with thin paste. BINDING RECORD Preparation of books for the bindery. Closely associated with the work of mending and repair of books is that of the preparation of books for the bindery. Binders have com- plained of the careless and unbusiness-like methods of some librarians in this matter. Attention should always be given to the following: Handle a book to be bound with more care than when the binding is sound. Collate every book to make sure that no pages are missing, unless it is ascertained that the binder includes this process in his work. Many librarians have ceased to make bindery slips, except in the case of important books requiring compli- cated titles or for magazines. When slip is not made, an excellent way to indicate the lettering for the back of book, is to underscore lightly in lead pencil on title page, the specific words in title desired; for author underscore twice. The material to be used for binding is generally de- cided upon in advance by conference or correspondence with binder. Magazines should be carefully examined to make sure that each volume is complete, including title page and index. The librarian should write to the publisher for these, if they are not received within a reasonable time after the volume is completed. If missing, instruct binder to bind in stubs so that they may be inserted when obtained. In giving directions for magazines to be bound with stubs, state whether stubs are to be at the beginning or end of the volume. Look over previous volumes of set that your volumes may be uniform in the placing of the index, and follow the printer's arrangement. MENDING OF BOOKS 23 Send an alphabetical list of the books to the bindery for checking purposes. Keep a duplicate copy. File alphabetically in charging tray the book cards that have been removed from the books; charge these to the bindery. Magazines should have a bindery slip made and a sample volume already bound sent that each set may be uniform as to color of cover, lettering, etc. The slip should show definitely the placing and abbreviations of volume numbers, dates, etc. When books are returned from the bindery. Examine care- fully for flexibility; books should open flat; evenness of cover; compactness; correct and even lettering; reasonably wide margins. Check books with duplicate list. Pay no bills until all mistakes are rectified. Mis- takes in lettering can be corrected, and when this occurs return to the bindery. Enter in accession book under "remarks," opposite the entry of each book the date when the book was rebound: e. g., "reb'd 1 Jc., 16"; also on inside of lower front cover near 'the joint. A rubber stamp at small expense may be ordered from any stamp works, with the word "reb'd" to be inserted in the pencil date holder with the date. This saves writing. Enter on the monthly report blank the total number of books rebound. (This gives data for yearly total and obviates the necessity of keeping binding book.) TEMPORARY BINDERS The Gaylord Bros.' red rope binder provides an inexpensive magazine binder, both for the current periodicals in use in the reading room and those in circulation. The cover of the magazine may be pasted on the outside of the binder, and after the current month the magazine may be circulated just as a book, without damage for future binding. Information as to terms used in binding 1 and mending and illustrations of the structure of a book may be found in the following : A. L. A. Committee Binding for small libraries $ .15 Cockrell, Douglass Book binding and flie care of books . . Appleton 1.25 Coutts, H. T. and Stephens, G. A. Manual of library book binding Libraco, London 1.50 Dana, J. C. Book binding for libraries. . .Library Bureau .75 ^H RETURN TO the circulation desk of any University of California Library or to the NORTHERN REGIONAL LIBRARY FACILITY Bldg. 400, Richmond Field Station University of California Richmond, CA 94804-4698 ALL BOOKS MAY BE RECALLED AFTER 7 DAYS 2- month loans may be renewed by calling (510)642-6753 1-year loans may be recharged by bringing books to NRLF Renewals and recharges may be made 4 days prior to due date DUE AS STAMPED BELOW 20,000 (4/94) H UNIVERSITY OF CALIFORNIA LIBRARY