key: cord-1025454-evu7p6bt authors: Eiermann, André; Smrke, Samo; Guélat, Loïc-Marco; Wellinger, Marco; Rahn, Anja; Yeretzian, Chahan title: Extraction of single serve coffee capsules: linking properties of ground coffee to extraction dynamics and cup quality date: 2020-10-13 journal: Sci Rep DOI: 10.1038/s41598-020-74138-1 sha: 323484b89f886d70573032f26e4728e49c068736 doc_id: 1025454 cord_uid: evu7p6bt The objective of this paper is to elucidate the variables that govern coffee extraction from single serve coffee capsules. The study was conducted on 43 Nespresso and Nespresso-compatible capsules of the same geometry, from all of which the coffee was extracted on the same machine. This allowed the link between a range of coffee and capsule (input) parameters with coffee brew (output) variables to be studied. It was demonstrated that the most efficient way to increase total dissolved solids in the brew is to use more coffee for extraction, and/or to grind the coffee more finely. However, grinding too finely can lead to excessive flow restriction. The most significant new insight from this study is the importance of the proportion of fines (particles smaller than 100 µm) regarding the capsule extraction dynamics. Capsules with a higher share of fines, for similar median particle size of the ground coffee, led to longer extraction times. General rules applicable for capsule coffee product development were established, although fine-tuning of parameters for successful capsule coffee extraction remains specific to production line and type of coffee. The single serve coffee sector for ground coffee is divided into high pressure extraction from capsules and low-pressure extraction from soft pods. It is the fastest growing segment within the larger category of coffee products. The global coffee pod and capsule market combined is expected to grow from USD 15 billion in 2017 to USD 29 billion by 2025 at a compound annular growth rate (CAGR) of 8.5%. The high-pressure extraction capsules segment alone, which is the focus in this study, currently leads the coffee pod & capsule market and was valued at around USD 9.61 Billion in 2017 (63% of the whole single serve coffee segment). The domestic consumption of single serve coffee is currently expected to be increasing due to the lockdowns imposed during the 2020 Coronavirus pandemic. This growing consumer interest and economic importance of single serve coffee products has led to growing scientific interest but remains a relatively little studied topic. Single serve coffee has been used to study the extraction process, the composition of brews [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] and in the preservation of freshness of the ground coffee in hermetically sealed packaging 11, 12 . The single serve coffee sector encompasses a broad definition of packaging options, including pods and/or capsules, and is used to prepare a wide range of coffees from filter to espresso. Different systems vary with shapes and sizes of capsules, with the most common espresso capsule system being the Nespresso system. Recently, a surge of Nespresso-compatible products entered the market. The compatibles have the same shape as Nespresso capsules, but may differ in the material they are made of as well as in the origin and quality of the coffee itself. The advantage of studying the extraction of Nespresso and Nespresso-compatible coffee capsule is that the human factor is essentially eliminated from the brewing process. Furthermore, the brewing unit, and coffee bed geometry are very similar for all capsules. When these parameters are handled manually in preparing coffee (e.g. semi-automatic espresso), this results in a higher variability in extraction and cup quality 13 . Therefore, the wide spectrum of Nespresso and Nespresso-compatible coffee capsule products available on the market provides an excellent platform to systematically study the impact of specific parameters in high-pressure extraction from capsules, while brewing unit parameters are essentially kept constant. Ground coffee analysis. The capsules were opened and thoroughly emptied to measure the weight of the coffee per capsule (mean of 3 capsules). The roast level (colorimetric) was determined using a Colorette 3b meter (Probat, Emmerich, Germany). Particle size analysis was performed using an imaging particle size and shape analyser with a dual camera system Camsizer X2 (Retsch Technology GmbH, Haan, Germany). At least 10 g of coffee was used for each particle size analysis, and three measurements were performed per capsule type. Median particle size (X50) was determined as the volume weighted median particle size, based on the particle area projected on the images. The share of fines (Q 100µm ) was defined as the volume share of particles smaller than 100 µm in size. Three particle shape parameters were determined as volume weighted averages, sphericity (SPHT), symmetry (Symm) and aspect ratio (b/l) values. Capsule coffee extraction. The coffees were extracted from the capsules using a Krups Inissia XN1005 capsule machine. The weight of the brews was measured on-line during extraction whereby the aim was to reach 40 g by stopping the extraction manually. The resulting brew weight was 40.1 ± 0.3 g (mean ± s.d), with all brews between 39.6 and 40.7 g. The extractions were timed manually from starting the pump to cessation of the pump operation. Brew analysis. The concentration of coffee in the filtered brew (0.45 µm filter) was analysed using a VST LAB Coffee III refractometer (VST inc., Tulsa, US), calibrated using a soluble coffee sample prepared to a known concentration as according to the instrument instruction manual to display total dissolved solids (TDS) in coffee brews. The extraction percentage was calculated based on the mean weight of the coffee in each capsule type, brew weight and refractometric TDS measurement. The sensory test of coffees was performed by three Q-graders (certified Q Arabica Grader, by the Coffee Quality Institute). The sensory quality attributes that were determined were flavour, acidity, body and balance on a scale from 5 to 10. The quality of each attributes was assessed by tasting three replicates of the brew by each of the Q-grader. The final values were based on a subjective consensus of the tasters on the quality score that they give to each samples, rounded to the nearest 0.25 units. The reference of the attribute range was the quality that could potentially be achieved by an espresso coffee extracted as a semi-automatic espresso, where a score of 6 is average quality, and 10 exceptionally high quality. Statistical analysis. All data analysis and statistical analysis was performed using R statistical computing (R Foundation for Statistical Computing, Vienna, Austria) using integrated packages. All measurements of brews and capsules (Table 1) were conducted in 3 replicates per each sample. Defining espresso coffee and its quality is subject to discussion. Some link it to the concentration of solids found in the espresso brew 15 -the TDS. Others to the amount of water used per gram of coffee 16 -the brew ratio. Regardless of the perspective taken on the definition of what an espresso coffee is, the resulting low volume beverage should have a pleasant, distinct aroma, a complementary balanced profile between acid, bitter and sweetness as well as a pleasant tactile thickness, known as the body 15, 16 . As TDS will be heavily influenced by beverage volume, espresso brews prepared in this study were kept at a fixed beverage weight of 40 g. While brew weight was kept constant, the duration of extraction was allowed to vary and recorded to determine the average extraction flow rate. In the following, linear and multivariant correlations of extraction variables will be discussed first. Second, quality and sensory aspects of the extraction process will be addressed. Characterizing the coffee grounds. Grinding coffee generates particles with a bimodal distribution 17 . One local maximum occurs at greater particle sizes 18 and its location varies according to the adjustment (spacing) of the grinder burrs. For the sample in this study, this maximum is in the range 250-550 µm. The second local maximum occurs at smaller particle sizes, usually at around 50 µm. The particularity of this maximum is that its position seems to not be affected by the spacing of the grinding burrs. Median particle size rather than average was used in this study. The reason is that median particle size is less impacted by the amounts of fines, www.nature.com/scientificreports/ when such similar bimodal distributions are compared where the two peaks stay at the same position but only change in height. In Fig. 1 , the share of fine particles, Q 100µm is plotted as a function of the median particle size for the capsules measured in this study. The capsule coffee grinds show a wide spread in the amount (proportion) of fines, over the range from 6 to 16% of volume. Generally, there is a trend; as the coffee is ground more coarsely (larger Table 1 . Properties of the capsules analysed, ground coffees (X50-volume median mean particle size; Q 100µm -share of fine particles; Roast -roast level in Colorette Pt unit), brews (TDS -total dissolved solids; Extr. -extraction percentage), and the sensory scores of brews, sorted by ascending median particle size. Each line represents a capsule coffee product. The values with errors represent an average value and standard deviation (n = 3). Output extraction variables (brew properties) www.nature.com/scientificreports/ median particle size), the shares of fines become smaller. In this study, a large variation in the share of fines for a given median particle size was found, which is most likely due to different capsule product lines. Coffees can have the same 10% share of fines while the median particle size can vary from 300 µm up to 550 µm. When only a single product line is considered (e.g. capsules from a single manufacturer; red dots, Fig. 1 ), a distinct grouping is observed. This result possibly reflects the grind technology used by this manufacturer, since the share of fines is clearly negatively associated with the median grind size, with a narrow spread of the data, compared to all the capsules tested in this study. For a specific median particle size, the capsules from this manufacturer systematically show the lowest proportion of fines. Furthermore, the proportion of fines increases in a linear fashion with decreasing median particle size. Influence of particle size distribution on extraction dynamics. Extraction times were used as an indirect reflection of the extraction dynamics. The extraction times were found to be highly variable between different types of capsules, covering a range between 10 and 41 s (Fig. 2) , which corresponds to average flow www.nature.com/scientificreports/ rates in the 1-4 g/s range. When relating extraction times to particle size distribution, a highly significant positive association was found with Q 100µm (p < 0.001). Extraction time increased with increasing proportion of fines (Fig. 2b ). More specifically, over the sample population an increase in the proportion of fines from 10 to 15% corresponded to an increase in the extraction time of 10 s. In contrast, the volume median particle size was not found to be correlated with the extraction time (Fig. 2a) as otherwise seems to be the case in the extraction with semi-automatic espresso machines 19, 20 . Studies on the impact of the grind size for espresso extraction have mostly focused on the median or mean particle size 7,13,20 . The key variable that influences the hydrodynamics of espresso extraction is coffee bed permeability, which is a function of the particle size distribution of solids in the coffee bed and how the particles pack together to form the bed 19 . Hence, it is not only the median or mean particle size that plays a role in the permeability, but the overall particle size distribution also including the share of fine particles 19, 21 . Due to the large range of capsules and manufacturers included in this study, results are spread over a wide variety of Q 100µm ; X50 combinations ( Fig. 1) . Even though both parameters are related (Fig. 1) , and that probably a range of different grinding technologies are used by different manufacturers, this study indicates that coffee bed permeability is impacted more by the share of fines in the capsule coffees than by the particle size itself. When grinding coffee on a single grinder type, both Q 100µm and X50 are changing simultaneously (for example Fig. 1 , red dots), therefore extraction times will be related closely to the median particle size, as has been previously reported 19, 20 . However, as Fig. 2 illustrates, the extraction time seems to be much more significantly impacted by the shares of fines than the median particle size. In addition to searching for linear correlations, multiple regression analysis was applied to the data, in order to unveil multivariant correlations between capsule variables and extraction time (Fig. 3) . Multiple regression analysis confirms what is observed with linear correlations. Extraction time as a function of coffee weight in the capsule, volume median particles size, roast level, share of fines and capsule pressure was modelled using multiple regression analysis. With such a model, 42% of the extraction time variance can be predicted, and the two parameters Q 100µm (p < 0.0001) and X50 (p < 0.01) have significant importance for the regression. The extraction time can be predicted based on the model (Fig. 3a) , and the prediction works well for coffee extracting until 30 s extraction time, whereas for those that extracted longer than 35 s, the predicted values were smaller than the measured ones. The standardised model coefficient is double in value for Q 100µm than for X50 (Q 100µm 0.88, X50 0.45), and furthermore the expected coefficient for X50 would be negative, since smaller particle size could in theory only be associated with a longer extraction time. This result shows that there is some multicollinearity between share of fines and particle size, and confirms the higher importance of share of fines for controlling capsule extraction time, rather than particle size. We suspected that higher capsule pressure would lead to longer extraction time, due to a larger amount of trapped carbon dioxide in the coffee bed, a residue from the degassing process 22 . No correlation of the capsule pressure with the extraction dynamics was observed. Influence of capsule coffee properties on the cup properties. Espresso quality may be viewed as a complex extraction puzzle where the proper ratio of desirable components must be extracted simultaneously, in a matter of seconds, in order to produce the most desirable product. One of the characteristics of espresso coffee is its viscous, thick appearance, which is caused by high concentration of coffee solubles (TDS) 15 . High TDS is usually a highly desired quality of the espresso brew and is related to the sensory perception of "body". TDS is a www.nature.com/scientificreports/ non-specific analysis technique used routinely to gauge how much of the coffee was extracted into the cup, also called extraction yield. Extraction time, coffee weight and proportion of fines were found to positively correlate with the TDS of the resulting brew (Fig. 4b-d) . Negative correlation of the particle size with the TDS was found (Fig. 4a) , which is expected and was reported before 23 . The extraction percentage-shows essentially the same relations with the variables mentioned above. This is because extraction percentage is calculated by multiplying TDS by brew weight and dividing by the coffee weight, and the brew weight was kept constant for all extractions in this study. Unsurprisingly, the most direct relation and strongest correlation among those observed in this study is the weight of the coffee in the capsule with the TDS of the brew. Packing more coffee in the same extraction system will lead to a more concentrated brew when brewing to a fixed beverage weight. The linear relation observed follows the theoretical increase of TDS that should be observed when assuming the same extraction percentage from all capsule coffees (Fig. 4c) . Indeed, over the whole range of capsules tested here, no relation of extraction percentage (in %) with the weight of coffee in the capsule was found (variable relation not shown). Longer extraction times and hence slower flow rates are related to brews with higher TDS. The effect is surprisingly high, even though as reported by Melrose et al. the bed extraction efficiency theoretically does not increase significantly with longer extraction times 21 . The data from this study indicate a possible "saturation" effect at extraction times above 25 s (Fig. 4d) . The extraction time and coffee weight show no significant correlation. The inverse correlation of TDS (and extraction percentage) with particle size is known and is explained by increased extraction efficiency from smaller particle size that enable the solubles to diffuse from the particles more quickly 21 . The complex correlation of variables observed here could also be impacted by the product www.nature.com/scientificreports/ specifications. Since consumers expect an espresso to be a thick and a strong brew, finer grind sizes with a higher share of fines are used to maximize the extraction percentage. Hence, long extraction times might be acceptable, and the pressure needed to extract the capsule pushed to the limit of the capsule machine by producers to achieve desired brew quality. We see some weak correlation (p < 0.05, data not shown) of TDS with roast level. This result may be attributed to the fact that the recipes for the capsules vary greatly, and darker roasted coffees could be preferred by consumer, as this leads to coffee with a stronger body. Hence, the correlation of roast level with TDS could not be attributed directly to better extractability of darker roasted coffee, since the grind properties play a more important role in the extraction behaviour. Multiple regression analysis of TDS as a function of coffee weight, X50, Q 100µm , roast level and capsule pressure (52.7% of TDS variance predicted) revealed that decreasing the particle size of the grounds, X50 and increasing the coffee weight, had the most prominent impact on TDS (standardized model coefficients -0.43 and 0.32, p < 0.01 and p < 0.01). The prediction of TDS based on the multiple regression model is shown in Fig. 3b . The authors are aware that the indicators of importance of variables (coefficient and p-value) in models are not completely robust, since the independent variables have clearly some multicollinearity. While building the multiple regression models it was found that the results are consistent, even when subsets of samples were modelled. This was the case when independent variables that were not important were excluded from the model, or other variables were included (for example, including time as an independent variable for the TDS model). Hence, it seems reasonable to conclude that the results from the multiple regression analysis revealed with good statistical confidence the importance of the variables predicting the TDS in the brew and the extraction time. As 43 different commercial capsule coffees were tested (Table 1 ) in this study, it was anticipated that flavour attributes would vary between products due to the potential use of different origins, varietals, processing methods, roast levels, grinds and blends. Nevertheless, body is particular as it represents a tactile sensation attributed to solids extracted from the coffee during brewing and becoming suspended in the beverage, making them quantifiable by measuring the TDS 24 . Consequently, the sensory results have not shown correlations with technical variables apart from a suspected trend no significance of body correlated with TDS (p = 0.21). The Q-grading sensory evaluation was focused on the quality of the brew. The sensory results were mainly of values close to 6, since the coffee brews in this study did not reproduce the range of Q-grader results that could be expected for coffees prepared using a semi-automatic espresso machine and highest quality coffees. Some of the outliers in the sensory results could be explained by the parameters of the capsules. Two samples were found to have higher oxygen content in the capsule (samples 27 and 42) and scored lower in the sensory. Another two samples that were found to be higher than average in the sensory results (samples 19 and 40) could be explained to be of higher green coffee quality, since those samples were single origin Colombian and Ethiopia coffee. These sensory results and the lack correlation to technical parameters are not surprising since they show that most of the capsules have been optimised and produce average quality results. Only outliers in the sensory space were found as coffees of poorer production (oxygen in capsule) or coffees of above average green coffee quality. The orthogonality of sensory analysis results with capsule parameters is also shown by the principle component analysis (PCA), as displayed in Fig. 5 . The differentiation of the capsule samples by PCA is caused by ground coffee properties in PC1 axis, together with the sensory descriptor body, which has the same direction as coffee weight along the PC1 axis. As expected, based on results discussed earlier, the loadings of particle size and roast level have the opposite value in PC1 direction to other loadings, since lower values of those have been www.nature.com/scientificreports/ found associated with higher values of other ground coffee variables and TDS. The remaining sensory attributes are oriented orthogonal to the technical variables, parallel to the PC2 axis, further confirming that the sensory quality properties of the brew within the capsule landscape of studied samples are not significantly impacted by the physical properties of the ground coffee and by variations in extraction variables. The samples mentioned in the previous paragraph (19, 27, 40 and 42) are also outliers on the PC2 axis and are likely the cause of the orthogonality of the sensory to technical parameters on the PCA plot. Despite the wide variety of different capsule coffee formulations used for production of capsules subjected to this study, we can draw some general conclusions with respect to the extraction of coffee from capsules and espresso brew properties as a function of ground coffee parameters. The capsule extraction dynamics are highly influenced by the particle size distribution of coffee grounds. Only mean or median particle size information is insufficient to understand capsule extraction, therefore in this study we propose the parameter "share of fines; Q 100µm " as the second parameter for a simplified description of coffee grinds. The proportion of fines was highly correlated with increasing extraction time. The best way to increase TDS is to use more coffee for extraction, or to grind the coffee more finely to increase extraction efficiency. Grinding finer to increase extraction comes with a technical problem; finer grind sizes tend to form more finer particles in the grounds, which cause a decreased permeability of the coffee bed. This study shows that while there are certain general rules that can be followed for capsule coffee product development, the fine-tuning of parameters for a successful capsule coffee extraction is a problem specific to capsule production line (e.g. different grinder technology produces different share of fines in the coffee grinds). The coffee sensory quality in the cup was not correlated to the technical variables of the grounds. It is suspected that because most of the samples used in this study are optimised for the extraction, the cup quality can be only further improved by using higher quality green coffee. To better understand in what range the optimisation of technical parameters and green coffee quality affect brew quality, future studies with capsules produced using a controlled range of conditions need to be conducted. Received: 5 July 2020; Accepted: 24 September 2020 Investigation on the extractability of melanoidins in portioned espresso coffee Comparison of espresso coffee brewing techniques Optimization and application of a HS-SPME-GC-MS methodology for quantification of furanic compounds in espresso coffee Comparison of nine common coffee extraction methods: instrumental and sensory analysis caffeine content of retail market coffee in Portugal Carbohydrate content, dietary fibre and melanoidins: composition of espresso from single-dose coffee capsules Effects of capsule parameters on coffee extraction in single-serve brewer Rapid approach to identify the presence of Arabica and Robusta species in coffee using H-1 NMR spectroscopy Impact of consumer behavior on furan and furan-derivative exposure during coffee consumption. A comparison between brewing methods and drinking preferences Niacin, alkaloids and (poly)phenolic compounds in the most widespread Italian capsule-brewed coffees Freshness indices of roasted coffee: monitoring the loss of freshness for single serve capsules and roasted whole beans in different packaging An alternative approach to control the oxygen permeation across single-dose coffee capsules How the variance of some extraction variables may affect the quality of espresso coffees served in coffee shops Insight into the time-resolved extraction of aroma compounds during espresso coffee preparation: online monitoring by PTR-ToF-MS Espresso Coffee: The Chemistry of Quality The Craft and Science of Coffee Espresso Coffee: The Science of Quality The Craft and Science of Coffee A new methodology to estimate the steady-state permeability of roast and ground coffee in packed beds Changes in the aromatic profile of espresso coffee as a function of the grinding grade and extraction time: a study by the electronic nose system Toward a new brewing control chart for the 21st century Time-resolved gravimetric method to assess degassing of roasted coffee Chemical and sensorial characteristics of espresso coffee as affected by grinding and torrefacto roast Influence of coffee/water ratio on the final quality of espresso coffee A.E. and L-M.G. performed the experimental work, S.S. performed the data analysis, prepared the figures and wrote the results and discussion, A.R. wrote the introduction, M.W. and C.Y. reviewed the manuscript. The authors declare no competing interests. Correspondence and requests for materials should be addressed to C.Y.Reprints and permissions information is available at www.nature.com/reprints.Publisher's note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creat iveco mmons .org/licen ses/by/4.0/.