key: cord-0993175-67wznp1c
authors: Hu, Xu-Rui; Han, Meng-Fei; Wang, Can; Yang, Nan-Yang; Wang, Yong-Chao; Duan, Er-Hong; Hsi, Hsing-Cheng; Deng, Ji-Guang
title: A short review of bioaerosol emissions from gas bioreactors: Health threats, influencing factors and control technologies
date: 2020-04-09
journal: Chemosphere
DOI: 10.1016/j.chemosphere.2020.126737
sha: 98d9ff62a7ab92b8503d8fccc1ca34768e5a16b9
doc_id: 993175
cord_uid: 67wznp1c

Bioaerosols have widely been a concern due to their potential harm to human health caused by the carrying and spreading of harmful microorganisms. Biofiltration has been generally used as a green and effective technology for processing VOCs. However, bioaerosols can be emitted into the atmosphere as secondary pollutants from the biofiltration process. This review presents an overview of bioaerosol emissions from gas bioreactors. The mechanism of bioaerosols production and the effect of biofiltration on bioaerosol emissions were analyzed. The results showed that the bioaerosol emission concentrations were generally exceeded 10(4) CFU m(−3), which would damage to human health. Biomass, inlet gas velocity, moisture content, temperature, and some other factors have significant influences on bioaerosol emissions. Moreover, as a result of the analysis done herein, different inactivation technologies and microbial immobilization of bioaerosols were proposed and evaluated as a potential solution for reducing bioaerosols emissions. The purpose of this paper is to make more people realize the importance of controlling the emissions of bioaerosols in the biofiltration process and to make the treatment of VOCs by biotechnology more environmentally friendly. Additionally, the present work intends to increase people’s awareness in regards to the control of bioaerosols, including microbial fragment present in bioaerosols.

Biotechnology has become an important technology to control air pollution in the past decades (Kummer and Thiel, 2008; Deshusses, 1997) . For instance, bioreactor provides a clean, costeffective and environmentally friendly technology (Alonso et al., 1998; Esquivel-Gonzalez et al., 2017) . Biofiltration processes are based on the ability of microorganisms to attach to packing media in the form of biofilms (Groenestijn and Kraakman, 2005; Kim et al., 2007; Yang et al., 2011) . During the processing exhaust gas, these pollutants are absorbed by the biofilm and converted into carbon dioxide (CO 2 ), water (H 2 O), and biomass without generating undesirable by-products (Devinny et al., 1999; Kennes, 2012) . Biotechnology can effectively control low-concentration pollutants (Iranpour et al., 2005) . Therefore it has been successfully applied to treat a wide range of pollutants such as VOCs and odors (Mudliar et al., 2010; Girard et al., 2011) .

Biotechnology has many advantages for VOCs treatment (Martens et al., 2001; Sanchez-Monedero et al., 2003; Schlegelmilch et al., 2005; Chmielowiec-Korzeniowska et al., 2007) . However, it still has some drawbacks, such as the emission of bioaerosols (Wang et al., 2009; Yang et al., 2018) . Bioaerosols are very small particles suspended in the air that are living or coming from living organisms (Burge, 1990; Despr es et al., 2012) . Activated sludge and compost, often used as inoculation sources for biofilters, contain a large number of pathogenic bacteria, fungi, and viruses, etc. This might cause the release of bioaerosols containing pathogenic microbial microorganisms and microbial fragments during the biofiltration process, posing a great potential threat to human health (Ottengraf and Konings, 1991; Robertson et al., 2019; Menetrez et al., 2009; Ghosh et al., 2015; Zhou et al., 2016) . Some studies have shown that bioaerosol emission concentrations from bioreactors are usually higher than those of the background environment (Kummer and Thiel, 2008; Chung, 2007; Esquivel-Gonzalez et al., 2017) . Longterm exposure to bioaerosols in these environments may have adverse health effects (Pearson et al., 2015) .

Studies on the emissions of bioaerosols produced from biofilters have been increasing recently. However, the available studies have not comprehensively summarized and presented the state of bioaerosol emissions from biofilters. This paper reviewed the formation and emission of bioaerosols from biofilters, the potential impacts, the influencing factors on bioaerosol emissions and relevant control technologies, which was expected to contribute to better understand the impacts and to raise awareness on the need to curb the bioaerosol emissions, with the ultimate goal of helping to achieve complete control of these substances.

Biofiltration for VOCs removal is a complex combination of different physicochemical and biological phenomena. VOCs and oxygen pass through the packing media. Pollutants are transferred from the gas phase to the water phase and biofilm phase by diffusion before biodegradation (Cheng et al., 2016) . Microorganisms in the biofilm use VOCs as carbon sources to produce CO 2 , H 2 O, and biomass, etc. Microorganisms attach to the packing materials either naturally or as a result of engineering measures (Cohen, 2001) . Fig. 1 illustrates the basic principle of the formation and emission of bioaerosols from biofilters. During biofiltration, the airflow containing VOCs provides carbon sources for the biofilm. Over long periods of operation, a large amount of biomass accumulates and the biofilm attached to the surface of the packing materials becomes thicker simultaneously (Yang et al., 2010) . Thicker biofilms make it easier for microorganisms to exchange with air currents and be carried away from the packing materials. Moreover, not only dead microorganisms, but also injured microorganisms, fragments of cells, mycotoxins and endotoxins proteins liberated during the lysis process of cells will also fall off the packing materials during the growth of microorganisms in the biofilm. Finally, bioaerosols will be released from the biofilters in the exhaust gas, carrying considerable amounts of microbes out of the biofiltration process.

Some studies have reported that the outlet's bioaerosol concentration of biofilters is in the order of 10 3 e10 4 CFU m À3 (Ottengraf and Konings, 1991; Wang et al., 2009 Wang et al., , 2018 Yang et al., 2018) . Other researchers presented higher values than 10 4 CFU m À3 air of bioaerosol emissions in the air (Martens et al., 2001; Esquivel-Gonzalez et al., 2017; Valdez-Castillo et al., 2019) . Table 1 briefly summarizes relevant literature about bioaerosol emissions from biofilters. As presented from the Table, the concentration range of bioaerosol emissions from biofilters is remarkably wide. Bioaerosol emission concentrations from a bioreactor could range from 10 3 to 10 8 CFU m À3 (Schlegelmilch et al., 2005; Chung, 2007; Esquivel-Gonzalez et al., 2017) . The concentration of fungal spores emitted from a biofilter could reach 10 3 e10 6 CFU/m 3 , which would cause people exogenous hypersensitivity pneumonitis (Tolvanen and Hanninen, 2005; Vergara-Fern andez et al., 2012a; 2012b) . The Republic of Poland recommended that the occupational exposure limit for bacterial and fungal microorganisms is 5000 CFU m À3 (G orny, 2020). Most reported bioaerosol concentrations of the above studies exceeded the limit by 2e3 orders of magnitude, suggesting a great potential threat to human health.

The plate counting method is generally applied for the detection of bioaerosols concentration. Nonetheless, using this technique leads to an underestimate of bioaerosols because it only considers cultured cells. In fact, these cells make up at most about 20% of the total microbiome, in the case of bacteria and fungi. Esquivel-Gonzalez et al. (2017) found that bioaerosol emission concentrations were ranged from 6.4 Â 10 5 to 1.3 Â 10 8 cells m À3 air depending on a nonculture-dependent technique of epifluorescence microscopy, which were higher than those of plate counting method (Saucedo-Lucero et al., 2014) . Actually, dead microbes including the endotoxins and mycotoxins they produce can also cause damage to the human body (G orny, 2020).

Also, Table 1 shows that the bioaerosols emitted from biofilters contain different microbial species. Depending on the source of the inoculum, the species of microbes present in the biofilters are different. Bacteria and fungi were often detected from biofilters inoculated from activated sludge and compost in previous studies (Sanchez-Monedero et al., 2003; Chung, 2007; Wang et al., 2018; Valdez-Castillo et al., 2019) . Molds and spores were also presented in bioaerosols, which would cause inflammation and discharge (Ottengraf and Konings, 1991; Schlegelmilch et al., 2005; Vergara-Fern andez et al., 2012a; 2012b) .

Bioaerosols may cause respiratory problems, eye irritation, rash, and diarrhea due to the inclusion of microorganisms (viable or inanimate) and/or microbial metabolites (Husman, 1996; Menetrez et al., 2009) . Some studies have shown that bioaerosols contain some pathogenic microorganisms Balloy and Chignard, 2009; Cerdeno-Tarraga al., 2003) . Table 2 presents some of the pathogenic species in the bioaerosols reported in the literature, indicating the diversity of pathogenic species. Although bioaerosols come into contact with the human skin, most illnesses are caused by the body inhaling pathogenic microorganisms into the respiratory tract. Legionella pneumophila (L. pneumophila) and adenovirus are typically pathogenic organisms, causing respiratory disease, which have been detected in the air of wastewater treatment plants (WWPTs) (Dong et al., 2018; Masclaux et al., 2014) .

Some studies have presented that there are some qualitative evidence linking bioaerosol emissions from composting facilities to poor respiratory health in nearby residents (Pearson et al., 2015) . This is mainly due to the exposure of many pathogenic microorganisms to the air during the waste treatment process. The risk of waste treatment workers may depend on their specific occupational tasks, the proximity to the source of bioaerosols and the emission reduction systems used on-site (Douwes et al., 2003; Pearson et al., 2015) . L. pneumophila has been found not only from WWPTs and compost facilities, but also in the lungs of operators at these conditions, which has high-profile pathogenic bioaerosoltransmitted infection ability (Casati et al., 2010; Subbaram et al., 2017; Dong et al., 2018) . Table 3 shows some of the pathogenic microorganisms that are present during the waste treatment process (Cai and Zhang., 2013; W ery et al., 2008) . Not only pathogenic microorganisms, but also pathogenic viruses are present in the waste treatment processes (Otawa et al., 2007; Wu and Liu, 2009) . Several studies have shown that these pathogenic entities become bioaerosols that are emitted into the air during waste treatment (Bauer et al., 2002) . Some opportunistic pathogenic species including Acinetobacter sp., Pseudomonas sp., Enterococcus sp., and Bacillus sp. were isolated from the air emissions of wastewater treatment plants (WWTPs), which would cause respiratory disease, urinary tract infection, skin infection and septicemia, etc (Fracchia et al., 2006; Uhrbrand et al., 2017) . Ibanga et al. (2018) also presented that A. Fumigatus was emitted from a biofilter ranged of 1 Â 10 3 to 4.2 Â 10 3 CFU m À3 . It has been reported that more than 90% of pulmonary fungal diseases were caused by A. Fumigatus (Latg e, 2001). Moreover, some epidemic viruses have been detected in feces (Ding et al., 2004) , including the 2019-nCoV reported by the Chinese Center for Disease Control and Prevention's news. Since the activated sludge (including feces) and compost are often used as inoculation microorganisms in biofilters (from Table 1 ), the biofilters as a potential source of the human epidemic virus can not be ignored.

Operating conditions including biomass, inlet gas velocity, moisture content, temperature, can affect the bioaerosol emissions from biofilters (Zilli et al., 2005; Vergara-Fern andez et al., 2012a; Esquivel-Gonzalez et al., 2017) .

Some results have shown that biomass will affect bioaerosol emissions and higher biomass accumulation in biofilter leads to higher bioaerosol emission concentrations. Zilli et al. (2005) reported that the bioaerosol emission concentrations from the biofilter filled with sieved sugarcane bagasse were higher than those of the biofilter filled with peat under the same gas velocities, and the bioaerosol emission concentrations increased linearly as biomass increased. With the increase of the biofilm thickness, the binding force between the biofilm and the packing materials became weak, which caused the microorganisms to be carried by the airflow and emitted from the biofilter in the form of bioaerosols (Chung, 2007; Vergara-Fern andez et al., 2012a; Zilli et al., 2005; Wang et al., 2018) . Wang et al. (2009) also presented that the bioaerosol emission concentrations decreased in a combined process of UV-biofilter. The bioaerosol emission concentrations were reduced from 1.38 Â 10 3 CFU m À3 to less than 70 CFU m À3 when UV was used in the pretreatment stage. This is owing to the ozone generated by UV light that killed the microorganisms, then reduced the biomass in the biofilter.

Gas velocity determines the shearing force between the biofilm and airflow, which affects the bioaerosol emissions. Fig. 2 shows that when the gas velocity rises from 40 to 140 m h À1 , the total bioaerosol concentrations rise from 200 to 800 CFU m À3 (Wang , 2018) . Nevertheless, the bioaerosol concentration drops again when the gas velocity exceeds 160 m h À1 . An estimation of the shearing force exerted by the gas on the biofilm in a biofilter bed can be obtained using the Blake-Kozeny equation (Bird et al., 1960) :

where f is the friction factor; a is the specific surface area; d P is the particle size; r is the gas density; u is the gas superficial velocity.

This phenomenon may be related to the microbial flux on the surface of the packing materials and the dilution effect of gas emissions. It confirms that high gas velocity results in a strong shearing force on the biofilm, which makes it easy for microorganisms to be carried away from the packing materials (Lin et al., 2016; Wang et al., 2018) . Nicolella et al. (1996) also demonstrated that the detachment rate was strongly increased with superficial velocity. High gas velocity is not suitable for microbe aggregation, causing microbe slough off from carriers to the airflow. The thickness of the biofilm also became thin under these conditions (Vergara-Fern andez et al., 2012a). When the gas velocity reaches a certain flow rate, the biofilm would not fall off with the increase of gas velocity. Then the bioaerosol emission concentrations would decrease due to the dilution effect.

The gas temperature will also affect the bioaerosol emission concentration (Vergara-Fern andez et al., 2012b; Wang et al., 2018) . High temperatures cause a decrease in the bioaerosol emission concentrations. Fig. 3 shows the effect of temperature on bioaerosol emissions . The total concentration of bioaerosol emissions achieves the highest value at 30 C, while their concentration gradually decreases with further increasing temperature. High temperatures can cause cell lysis, and the biofilm and biomass accumulation rate will be negative, resulting in lower concentrations of bioaerosol (Vergara-Fern andez et al., 2012b). Moreover, high temperatures can accelerate the heat exchange rate between the airflow and the biofilm, which would lead to the loss ARGs is an abbreviation for antibiotics resistance genes.

Pathogens present in waste disposal that may produce bioaerosols.

Health impact Persistence in waste treatment Infectivity

Gþ of water in the microorganisms and affect their survival rates. High temperatures also caused microbial protein denaturation, which could affect microbial metabolism. Furthermore, the gas temperature will affect the species of bioaerosol emissions. Wang et al. (2018) found that fungal bioaerosol concentrations were higher than bacterial's when the temperature was below 40 C, while bacterial bioaerosol concentrations were higher than fungal's when the temperature was above 50 C. This was due to differences in the growth and metabolic capacity of different microorganisms at different temperatures. Also, when gas temperature increased, these unfavorable factors would promote fungi to form spores, thereby increasing the concentration of spore bioaerosols emissions. Vergara-Fern andez et al. (2012b) presented that higher concentrations of spore bioaerosol occurred when the temperature was 35 C, while lower concentrations of spore bioaerosol occurred when the temperature was 25 C.

The moisture content of packing materials will affect the emission of bioaerosol, and high moisture content will reduce bioaerosol emissions. Fig. 4 presents that the total bioaerosol concentrations decrease when the moisture content exceeds 70% . The water film thickness would maintain with the increase of moisture content, which would reduce the exposure of the biofilm to the airflow and the carrying of microorganisms by the airflow.

The moisture content will also affect the content of bioaerosol. Wang et al. (2018) presented that the peak concentration of bacteria was achieved with a moisture content of 70%, while fungi were achieved with a moisture content of 40%. This phenomenon might be explained by the fact that fungi are more suitable for growing in a dry environment, while bacteria are more suitable for growth in humid environments. Meanwhile, the higher moisture content will also reduce the content of spores in bioaerosols. The decrease in irrigation frequency brought about a gradual reduction in the moisture content of the bed, which promoted the emission of spores increased (Saucedo-Lucero et al., 2014) . Vergara-Fern andez et al. (2012b) also found that spore emission concentrations were decreased from about 2.2 Â 10 3 CFU m À3 air to about 1.3 Â 10 3 CFU m À3 air when the moisture content increased from 20% to 80%.

Other design and operating factors, such as packing materials, inoculation sources, and nutrients also influence bioaerosols emissions (Alvarez-Hornos et al., 2008; Vergara-Fern andez et al., 2012a , 2012b Esquivel-Gonzalez et al., 2017) .

According to the schematic diagram shown in Fig. 1 , microorganisms need to be attached to the packing materials during the operation of the biofilter. For different packaging materials, the porosity, particle size, and specific surface area are different, which leads to different environments for the growth of microorganisms and influences the accumulation rate of microorganisms. Larger particle sizes would result in higher biomass concentrations (Nicolella et al., 1996) . Esquivel-Gonzalez et al. (2017) found that perlite was better than Tezontle with a lower bioaerosol emission, which was due to a smaller diameter of perlite in their study. Ottengraf and Konings (1991) also presented that the concentration and composition of bioaerosols are different during the operation of the full-scale plants with different packing materials.

Meanwhile, inoculation sources will also affect the species of bioaerosol emissions. As shown in Table 1 , when the inoculation sources are activated sludge or compost, there is a production of multiple bioaerosols, while using a pure culture of microorganisms will only produce a single specie of bioaerosol. Schlegelmilch et al. (2005) used compost as an inoculation source and demonstrated that bioaerosol emission contained bacteria (mesophilic/thermophilic), molds (mesophilic/thermophilic), and actinomycetes (thermophilic). Saucedo-Lucero et al. (2014) used inoculation obtained from a hydrocarbon polluted site then added chloramphenicol to avoid bacterial growth. They found that the bioaerosol emissions contained only fungi and spores.

Increasing nutrient addition will lead to faster accumulation of biomass, which causes more bioaerosols emissions. Also, the lack of nutrients can lead to the formation of more spores. Vergara-Fern andez et al. (2012a) found that an increase in spore emission was observed when the nutrient was consumed, which was due to the fungus's defense mechanism to adverse conditions.

According to the traditional model of biofiltration shown in Fig. 1 , microorganisms will adhere to the surface of the packing materials and exchange substances with the VOCs-containing airflow. This process will cause the microorganisms to be carried by the airflow and exit the biofiltration process, resulting in the emission of bioaerosols. For reducing bioaerosols emissions from biofilter, microbial immobilization strategies can be utilized. Fig. 5A is the schematic diagram of the microbial immobilization methods. Immobilization microbial technology refers to the use of physical or chemical methods to locate free microorganisms in a limited space, but also to ensure the microbial activity and repeated utilization. Due to its high microbial density, low microbial loss and high reaction speed, immobilization technology has been applied to waste gas treatment since the 1990s (Paje et al., 1998; Miyake-Nakayama et al., 2006) .

The use of microbial immobilization strategies, especially the embedding method (Fig. 5B) , can effectively reduce the contact between microorganisms and airflow. This can reduce the carrying of microorganisms by the airflow, leading to a reduction in bioaerosol emissions. Although there have been studies on the application of the embedding method for processing VOCs in biofiltration, few studies have been conducted on their bioaerosol emissions. The application of embedding technology is very promising for biofiltration. In principle, embedding can not only improve the performance of biofiltration but can also reduce the emission of bioaerosols.

Several technologies have been studied to control bioaerosols. Ultraviolet light (UVeC) with a wavelength of 200e280 nm is an established means of disinfection. The wavelength of this band will (approximately 254 nm) cause direct damage to the microbes' DNA, thereby inactivating them. UV has been widely used for disinfection in the public health field (hospitals, health care facilities, public shelters), the food industry and the pharmaceutical industry as an environmentally friendly technology (Lee, 2011; Begum et al., 2009) . O 3 and H 2 O 2 are usually acting as strong oxidizing agents and biocide to inactivate microorganisms. They are more and more widely accepted as eco-friendly technologies and widely applied in the healthcare sector and food factories (Brodowska et al., 2017; Masotti et al., 2019) .

Some new technologies have emerged to control airborne microorganisms in recent years. Microwave (MW) is used to inactivate microorganisms by using electromagnetic wave radiation on bioaerosols in a short time, while it can result in the release of endotoxins (Wang et al., 2019b) . Plasma technology is the ionization of gas to produce charged ionized gaseous materials. These substances have high energy and can inactivate microorganisms quickly. Photocatalysis disinfection (PCD) relies on the generation of the free electrons and electron holes through light irradiation of the catalyst. These substances are highly oxidizing and can destroy cell membranes of bacteria and the proteins of viruses, even their RNA and DNA.

According to the literature reports and the characteristics of these control technologies, Table 4 presents and evaluates these technologies for inactivating bioaerosols. To summarise, UV, H 2 O 2 , and O 3 are accepted for its low energy consumption and high efficiency in application. While microwave and plasma are not used in up-scaled commercial applications due to the production of byproducts and the wear and energy consumption of equipment. PCD has high application prospects due to high inactivation efficiency and few secondary pollution. More researches are still needed to support and evaluate the practical application of relevant technologies in bioaerosol emissions from biofilters.

There have been some studies using related technologies to control bioaerosols from biofilters. Wang et al. (2009) developed a combined process of UV-biofiltration. The results demonstrated that UV as a pretreatment method could effectively reduce the emission of bioaerosol. Saucedo-Lucero et al. (2014) investigated the post-treatment photoreactor to control spore emission from a biofilter, which confirmed that spore deactivation efficiency of 98% was obtained for the photolytic and photocatalytic post-treatment processes. Valdez-Castillo et al. (2019) used the PCD as posttreatment on the bioaerosol emissions from biofilters. The results showed that the inactivation efficiency of bioaerosol could achieve as high as 70% with an active catalyst. These studies have demonstrated the potential of control technologies to reduce bioaerosol emissions from bioreactors.

In the case of inactivation technologies, technologies including UV, microwave, PCD, and plasma consume electrical energy and convert it into other forms of energy that act on bioaerosols. Table 5 summarizes the inactivation efficiency and energy consumption of the various control technologies mentioned above. The energy consumption of H 2 O 2 is converted according to the amount and price of H 2 O 2 , which is converted into the required money and equivalent to the consumption of electricity. O 3 energy consumption is estimated according to the parameters of the generator model and dosage.

To evaluate the inactivation performance of different technologies on bioaerosol, the EE/O calculation was used in this study to characterize the energy efficiency of the technologies according to the following equation (Xie et al., 2017; Chen et al., 2019) .

where EE/O is the energy required to inactivate bioaerosol by one order, J m À3 ; P is the power of the device, W; t is the reaction time, s; V is the volume of the bioaerosols, m 3 ; C 0 and C t are the concentrations of bioaerosols at the beginning and at a given time t, respectively, CFU m À3 . It can be seen from Table 5 that UV, microwave, PCD, and plasma can inactivate microorganisms in a short time, but the device consumes much energy. Especially for the microwave consumption exceeds than 10 7 J m À3 . Chemical fogging (H 2 O 2 ) and O 3 inactivation are less effective than other techniques but present long term inactivation effects. Fig. 6 shows the EE/O ratio of bioaerosols inactivation obtained with different control technologies. Microwave has the highest energy consumption. While chemical fogging (H 2 O 2 ) and O 3 consumption are at a low level of all the technologies. According to the literature survey of bioaerosols inactivation, plasma, chemical fogging (H 2 O 2 ) and O 3 are more suitable for the application of largescale inactivation of bioaerosols. For treating the bioaerosolcontaining gas emitted during biofiltration, the gas can be introduced into the inactivation equipment for treatment or be passed through the gas absorption liquid containing chemical disinfection reagents.

Biofilters are often inoculated by activated sludge and compost, which would contain a large number of pathogenic bacteria and viruses. Therefore bioaerosol emissions from biofilters are generally higher than background values, which would cause lung disease and inflammation, and pose a great potential threat to human health. Additionally, many factors influence the emissions of bioaerosols during biofiltration. High biomass accumulation results in high concentrations of bioaerosol emissions. Increasing gas velocity will raise the bioaerosol emissions first and then decrease the concentrations due to the shearing force and dilution effect. High moisture content and temperatures will reduce bioaerosol emissions and have an impact on bioaerosol species. As for bioaerosols control technologies, UV, H 2 O 2 , and O 3 are applicable for its low energy consumption and high inactivation efficiency. Also, PCD is a very promising technology for controlling bioaerosol because of the less secondary pollution generation and high inactivation efficiency.

Moreover, more comprehensive techniques should be used to monitor the bioaerosols rather than just relying on the inactivation monitor. Not only living microorganisms, but also microbial fragments can cause damage to the human body. The monitoring and counting techniques of bioaerosols are necessary for homogenization, and these can be taken into account to establish legislation. New methods of characterization and health risk assessment are also needed due to health effects is the function of the species of 

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Dynamic mathematical model for the biodegradation of vocs in a biofilter: biomass accumulation study

Biofiltration of ethylbenzene vapours: influence of the packing material

The innate immune response to Aspergillus fumigatus

Bacteria and fungi in aerosols generated by two different types of wastewater treatment plants

Inactivation of food spoilage fungi by ultra violet (UVC) radiation

Transport Phenomena

Workers' exposure to bioaerosols from three different types of composting facilities

The assessment of airborne bacterial and fungal contamination emitted by a municipal landfill site in Northern Poland

Bioaerosols: prevalence and health effects in the indoor environment

Detecting human bacterial pathogens in wastewater treatment plants by a high-throughput shotgun sequencing technique

Compost facilities as a reservoir of Legionella pneumophila and other Legionella species

The complete genome sequence and analysis of Corynebacterium diphtheriae NCTC13129

Kinetic, mechanism and mass transfer impact on electrochemical oxidation of MIT using Ti-enhanced nanotube arrays/SnO2-Sb anode

Efficacy of a novel biofilter in hatchery sanitation: I. Removal of airborne bacteria, dust and endotoxin

Evaluation of gas removal and bacterial community diversity in a biofilter developed to treat composting exhaust gases

Biofiltration d the treatment of fluids by microorganisms immobilized into the filter bedding material: a review

Biological waste air treatment in biofilters

Primary biological aerosol particles in the atmosphere: a review

Biofiltration for Air Pollution Control

Organ distribution of severe acute respiratory syndrome (SARS) associated coronavirus (SARS-CoV) in SARS patients: implications for pathogenesis and virus transmission pathways

Deactivation of Legionella Pneumophila in municipal wastewater by ozone generated in arrays of microchannel plasmas

Characterization of bioaerosol emissions from two biofilters during treatment of toluene vapours using epifluorescence microscopy

Site-related airborne biological hazard and seasonal variations in two wastewater treatment plants

Rapid inactivation of airborne bacteria using atmospheric pressure dielectric barrier grating discharge

Review of bioaerosols in indoor environment with special reference to sampling, analysis and control mechanisms

Biofiltration of methane at low concentrations representative of the piggery industry d influence of the methane and nitrogen concentrations

Microbial aerosols: sources, properties, health effects, exposure assessment d a review

Recent developments in biological waste gas purification in Europe

Health effects of indoor-air microorganisms

Pilot-scale biofiltration at a materials recovery facility: the impact on bioaerosol control

Literature review of air pollution control biofilters and biotrickling filters for odor and volatile organic compound removal

Six kinds of indoor air disinfection methods: comparison of their effects

UV-A photocatalytic treatment of high flow rate air contaminated with Legionella pneumophila

Biological agent inactivation in a flowing air stream by photocatalysis

Biotechniques for air pollution control and bioenergy

Integrated treatment scheme of a biofilter preceded by a two-bed cyclic adsorption unit treating dynamic toluene loading

Germicidal UV sensitivity of bacteria in aerosols and on contaminated surfaces

Bioaerosols d sources and control measures

The pathobiology of Aspergillus fumigatus

Life comes from the air: a short review on bioaerosol control

Effects of small-size suspended solids on the emission of Escherichia coli from the aeration process of wastewater treatment

Effect of air pollution on the total bacteria and pathogenic bacteria in different sizes of particulate matter

Reduction potential of microbial, odour and ammonia emissions from a pig facility by biofilters

Assessment of airborne virus contamination in wastewater treatment plants

Airborne contamination in the food industry: an update on monitoring and disinfection techniques of air

An evaluation of indoor and outdoor biological particulate matter

Biodegradation of dichloromethane by the polyvinyl alcohol-immobilized methylotrophic bacterium Ralstonia metallidurans PD11

Gas phase photocatalytic bacteria inactivation using metal modified TiO2 catalysts

Bioreactors for treatment of VOCs and odours d a review

An experimental model of biofilm detachment in liquid fluidized bed biological reactors

Abundance, diversity, and dynamics of viruses on microorganisms in activated sludge processes

Emission of microorganisms from biofilters

Susceptibility constants of airborne bacteria to dielectric barrier discharge for antibacterial performance evaluation

Indoor air disinfection using a polyester supported TiO2 photo-reactor

Exposures and health outcomes in relation to bioaerosol emissions from composting facilities: a systematic review of occupational and community studies

Bioaerosol exposure from composting facilities and health outcomes in workers and in the community: a systematic review update

Inactivation of airborne microorganisms using novel ultraviolet radiation sources in reflective flow-through control devices

Biofiltration at composting facilities: effectiveness for bioaerosol control

Hexane abatement and spore emission control in a fungal biofilter-photoreactor hybrid unit

The potential to reduce emissions of airborne microorganisms by means of biological waste gas treatment systems

Investigation of removal capacities of biofilters for airborne viable micro-organisms

Isolation, identification, characterization and antibiotic sensitivity profile of pathogenic Legionella pneumophila isolates from different water sources

Sulfur dioxide and oxylene co-treatment in biofilter: performance, bacterial populations and bioaerosols emissions

Observation on efficacy of four chemical disinfectants in disinfection of air

Occupational hygiene in a waste incineration plant

Assessment of airborne bacteria and noroviruses in air emission from a new highlyadvanced hospital wastewater treatment plant

Photocatalytic inactivation of airborne microorganisms in continuous flow using perlite-supported ZnO and TiO2

Inactivation of bacteria in flight by direct exposure to nonthermal plasma

Influence of the inlet load, EBRT and mineral medium addition on spore emission by fusarium solani in the fungal biofiltration of hydrophobic VOCs

Temperature and moisture effect on spore emission in the fungal biofiltration of hydrophobic VOCs

Inactivation of airborne bacteria using different UV sources: performance modeling, energy utilization, and endotoxin degradation

Reduction of toxic products and bioaerosol emission of a combined ultraviolet-biofilter process for chlorobenzene treatment

Microwave-induced release and degradation of airborne endotoxins from Escherichia coli bioaerosol

Study on In-Duct Ultraviolet Germicidal Irradiation (UVGI) Dynamic Air Disinfection Technology (Master's Degree Thesis)

Dissimilar emission characteristics between bioaerosol and suspended particles from gaseous biofilters and bioaerosol health risk evaluation

Distribution of antibiotic resistance genes and bacteria from six atmospheric environments: exposure risk to human

Behaviour of pathogenic and indicator bacteria during urban wastewater treatment and sludge composting, as revealed by quantitative PCR

Determination of virus abundance, diversity and distribution in a municipal wastewater treatment plant

Inactivation of bacteria and fungus aerosols using microwave irradiation

A Study on the Effects and Relevant Mechanisms of Microwave Irradiation and Cold Plasma on Viability of Bioaerosols

Inactivation of airborne viruses using a packed bed non-thermal plasma reactor

Experiment and observation of ozone disinfection effect on air. Guizhou animal science and veterinary medicine (China)

Electrochemical oxidation of ofloxacin using a TiO2-based SnO2-Sb/polytetrafluoroethylene resin-PbO2 electrode: reaction kinetics and mass transfer impact

Biomass accumulation and control strategies in gas biofiltration

Performance of biotrickling filters packed with structured or cubic polyurethane sponges for VOC removal

A full-scale thermophilic biofilter in the treatment of sludge drying exhaust: performance, microbial characteristics and bioaerosol emission

Isolation of H5N6, H7N9 and H9N2 avian influenza A viruses from air sampled at live poultry markets in China

Detachment and emission of airborne bacteria in gas-phase biofilm reactors

This study was supported by the National Natural Science Foundation of China (Grant No. 51678402).