key: cord-0976212-qh1mlxn3 authors: Wehling, Julia; Köser, Jan; Lindner, Patrick; Lüder, Christian; Beutel, Sascha; Kroll, Stephen; Rezwan, Kurosch title: Silver nanoparticle-doped zirconia capillaries for enhanced bacterial filtration date: 2015-03-01 journal: Mater Sci Eng C Mater Biol Appl DOI: 10.1016/j.msec.2014.12.001 sha: 25d445e0e24fde9fdc3161a9f00faeb40e0eb3b8 doc_id: 976212 cord_uid: qh1mlxn3 Membrane clogging and biofilm formation are the most serious problems during water filtration. Silver nanoparticle (Ag(nano)) coatings on filtration membranes can prevent bacterial adhesion and the initiation of biofilm formation. In this study, Ag(nano) are immobilized via direct reduction on porous zirconia capillary membranes to generate a nanocomposite material combining the advantages of ceramics being chemically, thermally and mechanically stable with nanosilver, an efficient broadband bactericide for water decontamination. The filtration of bacterial suspensions of the fecal contaminant Escherichia coli reveals highly efficient bacterial retention capacities of the capillaries of 8 log reduction values, fulfilling the requirements on safe drinking water according to the U.S. Environmental Protection Agency. Maximum bacterial loading capacities of the capillary membranes are determined to be 3 × 10(9) bacterial cells/750 mm(2) capillary surface until back flushing is recommendable. The immobilized Ag(nano) remain accessible and exhibit strong bactericidal properties by killing retained bacteria up to maximum bacterial loads of 6 × 10(8) bacterial cells/750 mm(2) capillary surface and the regenerated membranes regain filtration efficiencies of 95–100%. Silver release is moderate as only 0.8% of the initial silver loading is leached during a three-day filtration experiment leading to average silver contaminant levels of 100 μg/L. Water purification technologies play an important role in reducing the risk of the dissemination of waterborne diseases or epidemic outbreaks that are caused by pathogenic microorganisms and viruses. Bacteria such as pathogenic serovars of Salmonella and Vibrio cholerae are responsible for severe diseases such as typhoid fever and cholera, and Escherichia coli serves as an important indicator organism for fecal contaminations. Today, more than 250 serotypes of E. coli are known ranging from harmless gut commensals to severe pathogens [1] , such as the virulent enterotoxigenic (ETEC), enteropathogenic (EPEC), and enterohemorrhagic (EHEC) E. coli. Furthermore, viral infections can be spread via drinking water contaminations and highly infectious diseases are for example hepatitis A, poliomyelitis caused by the poliovirus or the severe acute respiratory syndrome (SARS) which is caused by the coronavirus. Because bacterial contaminations in drinking water are nowadays the main reason for most of the upcoming diseases [2] , the removal and inactivation of pathogenic coliforms and other microorganisms are therefore a field of great interest for both, industries and local authorities. These institutions are obliged to fulfill the requirements on water containing 0 fecal and total coliform counts in 100 mL of water intended for drinking [3] . Hence, small-sized water filtration systems that can be easily transported and provide sufficient amounts of purified water are of global interest [4] . Different filtration materials have been described for the use in water purification, such as polymeric materials like cellulose acetate (CA) [5] , polysulfone (PS) [6] , polyacrylonitrile (PAN) [7] or polyvinylidene fluoride (PVDF) [8] , while polyethersulfone (PES) is the most commonly used material for membrane applications [9] . In contrast to polymeric filter materials, ceramics feature outstanding positive properties because they are usually bio-inert, do not undergo swelling, are chemically and thermally stable, and withstand high mechanical stress enabling the cleaning and reuse of the filter after heat or acid/base treatment for decontamination [10, 11] . These excellent properties result in an increased membrane service life compensating the higher costs of ceramics in comparison to polymeric materials. The most common problem during bacteria filtration is the formation of biofilms on the membrane surface leading to pore clogging and consequently, a reduction of the filter performance is given. These clustered bacterial communities are attached to the membrane surface and protect themselves against environmental influences. Bacteria produce extracellular polymeric substances (EPS) to form complex macroscopic structures that increase their resistance against e.g. toxic chemicals and antimicrobial agents. The removal of biofilms from the membrane surface is challenging and results in both cost-and time-intensive membrane regeneration procedures. Therefore, the reduction of the initial physical attraction of bacteria to the membrane surface, which can be attributed to a reversible attachment [1] , plays a key role in inhibiting the formation of biofilms and several antibacterial surfaces have already been proposed [12, 13] . Especially, immobilized nanosilver can act as an efficient antibacterial agent by killing retained bacteria directly on the membrane surface. The decoration of filtration membranes with nanomaterials [14] have come into spotlight for water decontamination, catalysis and environmental remediation exploiting their unique surface chemical activities. Though the use of silver as an antimicrobial agent is known for about 7000 years [15] , upcoming with the urgent need to eradicate antibiotic-resistant bacteria and with new insights into the mechanism of action [16] , the use of silver has regained an emerged interest along with new interesting fields of applications [17] . Silver displays a broad antibacterial spectrum against Gram-positive and -negative bacteria [18] and nanosilver is one of the safest and mildest antibacterial agents for mammalian cells [19] . In recent years, silver nanoparticles (Ag nano ) have been embedded into various materials to generate antibacterial composites [20] [21] [22] [23] and especially polymeric nanocomposite membranes are produced for water filtration purposes [6, 14, [24] [25] [26] [27] , since nanoparticles feature advantages in comparison to bulk silver: i) very small amounts of silver are needed due to the high specific surface area of silver nanoparticles, ii) when compared to silver ions, the bactericidal effect of Ag nano is long-lasting because zerovalent (metallic) Ag nano are not inactivated by complexation and precipitation [28] and iii) a controllable release of Ag + -ions from the particles [29] compose them a cost-effective material for surface coatings. Most of the studies investigated the antibacterial properties of the nanocomposite membranes by describing the effect of the physical contact between silver nanoparticles and bacterial cells, but experiments were not performed under filtration conditions with special focus on antibacterial efficiency and silver leaching [27] . In our study, we present an advanced water filtration system based on ceramic capillary membranes which are subsequently doped with Ag nano . Using zirconia as the membrane material and Ag nano as the bactericidal coating, we combine a promising filtration material exhibiting high fracture toughness and bending strength with a highly effective antibacterial agent. Pore sizes of the capillary membrane of less than 0.2 μm and high open porosities of 51% enable the retention of bacterial cells during filtration [30] . Generated by direct reduction of silver nitrate on the membrane surface, immobilized Ag nano display a bactericidal surface that kills filtrated bacteria directly on the membrane surface. Filtration experiments were performed by applying intracapillary feeding with bacterial suspensions and bacterial retention after different filtration times was determined using microbiological methods. The viability of retained bacteria was analyzed to evaluate the bactericidal action of immobilized Ag nano and silver leaching during filtration was determined to consider eco-toxicological requirements. Zirconia capillary membranes were fabricated by extrusion and sintered at 1050°C for 2 h as described in our previous study [30] . As shown in Fig. 1 , Ag nano were immobilized on the membrane surface by a two-step immersion procedure according to the Creighton method [31] by direct reduction of silver ions on the surface of the capillaries. Capillaries featured an outer diameter (D O ) of 1.48 ± 0.01 mm, an inner diameter (D I ) of 0.90 ± 0.01 mm and an average wall thickness of 0.29 mm ± 0.01 mm. For all further tests, capillary pieces of 25 mm length were used which is in accordance with a weight of 82.9 ± 0.7 mg and a geometric surface area of 189 mm 2 , except for the filtration experiment where 100 mm capillaries were applied (geometric surface area of 750 mm 2 ). For the immobilization of Ag nano one sintered capillary with a length of 25 mm was immersed in 2 mL silver nitrate (AgNO 3 ) solution (Sigma Aldrich, Germany, product number 209139) with varying concentrations from 2.5 to 10 mM at 25°C and shaken at 1000 rpm for 5 min (pH was not adjusted). For the reduction of the immobilized silver ions, capillaries were subsequently immersed in 2 mL sodium borohydrate (NaBH 4 ) (Sigma Aldrich, Germany, product number 209139) for further 5 min. The reduction of the pre-immobilized silver ions was performed using a constant concentration of 2 mM NaBH 4 . Prior to use, the NaBH 4 solution was stirred for 30 min at 25°C followed by a cooling step to 4°C without adjusting the pH. The number of immersion steps was varied between 1, 3, 5 and 10. Afterwards, the capillaries were washed twice in 15 mL of ddH 2 O under shaking at 1000 rpm The extruded capillaries were dried at room temperature for 2 days and the obtained green parts were sintered at 1050°C for 2 h. Silver ions were directly reduced on the surface of the capillary membranes by immersion in AgNO 3 solution with varied concentrations and subsequently reduced in NaBH 4 at a constant concentration of 2 mM. This two-step immersion procedure was repeated 1-5 times to obtain adequate silver loading capacities. for 5 min to remove unbound and weakly bound silver and finally dried at 70°C for 30 min. Silver loading capacities were determined by three different methods: i) manual counting of immobilized Ag nano , ii) image analysis using an image processing algorithm and iii) atomic absorption spectroscopy (AAS). Scanning electron microscopy (SEM) micrographs of untreated and Ag nano -capillaries were taken with a SEM Supra 40 (Carl Zeiss, Germany) operated at 2 kV. The chemical composition of both the membrane material and immobilized Ag nano was recorded using an energy-dispersive X-ray spectroscopy (EDX) detector (BrukerXFlash 6| 30, Bruker Nano GmbH, Germany). The number of immobilized Ag nano on the membrane surface was determined by manual counting using three different SEM micrographs for each membrane sample and four randomly chosen micrograph sections covering an area of 1 μm 2 . Additionally, the micrographs were analyzed using an image processing algorithm called "Silver-Particle Analyzer". The algorithm was developed in C# using Visual Studio 2012 with. NET 3.5 Framework and AForge.NET 1.7.0 Framework. The program used the characteristic gray-value distribution of the Ag nano on the SEM micrographs. The analyses were carried out by screening the SEM images with a so-called tophat filter. The top-hat filter is applied at a fixed size of 7 × 7 pixels which can be attributed to the size range of the Ag nano . To consider exclusively the Ag nano and no parts of the porous substrate, the contrast was increased and a threshold value for bright image segments was applied. The algorithm was used to quantify the percentage of Ag nano -covered capillary surface and the total surface of bioactive silver based on the assumption that all Ag nano were spherical. Results were compared with total silver loadings obtained from AAS analysis. AAS measurements were performed to determine the total amount of immobilized Ag nano on the surface of the capillaries. To quantify the silver loading, one 100 mm Ag nano -capillary was acidified in 10% HNO 3 at 25°C overnight. Due to applied acidic conditions, a complete release of the immobilized silver from the capillaries was enforced. An aliquot of 100 μL of the solution was stored at 4°C until AAS measurements were performed (measurements were performed in triplicate using three individual capillaries). The silver loading was quantified by graphite furnace AAS using a Unicam 989 QZ AA Spectrometer with GF90 plus furnace and FS90 plus autosampler (Unicam, Cambridge, UK) after aqua regia digestion. The digestion was carried out by adding 80 μL of concentrated HCl (37%, p.a. VWR, Germany) and 20 μL of concentrated HNO 3 (≥ 65%, puriss p.a., Sigma-Aldrich, Germany) to the samples. After short mixing and centrifugation, the open samples were tempered at 56°C overnight. The dry residue was dissolved in 1 mL diluted aqua regia (containing 10% HNO 3 and 19% HCl). Subsequently, the samples were measured after further dilution to be in the working range of the AAS (0.5-20 μg Ag L −1 ). For all tests, bacterial suspensions of E. coli (Deutsche Sammlung von Mikroorganismen und Zellkulturen, Germany, DSMZ No. 1077) were prepared by inoculating a pre-culture in 70 mL of lysogeny broth (LB) (Sigma Aldrich Germany, No. L3022) for 16 h at 37°C to allow a growth until the stationary phase is reached. Bacterial cells were washed once in OECD medium, which is used to simulate realistic surface water conditions [32] and the cell pellet collected by centrifugation was resuspended in OECD medium to obtain a realistic bacterial cell concentration of 10 8 cells/mL for wastewaters [33] according to McFarland standards [34] . Before use, capillaries were heat sterilized at 160°C for 3 h. According to preliminary tests, this sterilization did not affect the bactericidal properties of the capillaries (data not shown). Ag nano and untreated capillaries as a reference (each 25 mm length) were separately incubated in 4 mL E. coli suspensions at RT and 200 rpm for 30 min. After incubation, the capillaries were briefly washed in OECD medium to remove residual bacterial cells from the inner channel of the capillary (lumen), and subsequently placed on fresh LB plates containing 1.5% (w/w) agar. Incubation of the plates was performed at 37°C for 24 h allowing the bacteria to grow. Bacterial suspensions of E. coli were used for filtration purposes using untreated and Ag nano -capillaries with accessible lengths of 100 mm, respectively. Filtration tests were performed in dead-end mode. Therefore, one end of the capillary was sealed with a twocomponent polydimethylsiloxane glue (Wirosil®, BEGO, Germany), while the other end of the capillary was connected to a convenient silicon tubing. Four individual capillaries (untreated vs. Ag nano ) and independent bacterial cultures were used. For intracapillary feeding with bacterial suspensions, a peristaltic pump (BVB Standard, Ismatec, Germany) was set to a constant flow rate of 250 μL min −1 . Permeates were collected and analyzed regarding the presence of bacterial cells using three different microbiological methods. Adenosin triphosphate was used as an indicator of bacterial metabolism and measured using a luciferase-based cell viability assay as described by Lara et al. [35] . 50 μL of the permeate was mixed with 50 μL of BacTiterGlo Assay (Promega No. G8231, Germany) and luminescence counts, directly correlating with the amount of present ATP, were recorded using a luminescence plate reader (Chameleon V, Hidex, Germany). Furthermore, the optical density of the bacterial suspension at 595 nm (OD 595 nm ) was measured using a plate reader (Chameleon V, Hidex, Germany). Colony forming units (CFU) were determined by plating the undiluted permeate onto agar plates (Coliform Count Plate, Petrifilm, 3 M, Germany) and CFUs were counted after an incubation at 37°C for 24 h. All experiments involving ATP assay, OD measurements, and CFU tests were performed using three replicates. Obtained results based on permeate samples were compared with those from the bacterial feed solution which were set as 100% survival of bacteria cells. Preliminary results showed that capillaries stood a bacterial load which was corresponding to a membrane flux reduction of 30%, which was reached after 150 min. Consequently, filtration was stopped after 150 min and back flushing was initiated to remove retained bacterial cells from the inner capillary membrane surface. For this, capillaries were immersed into fresh OECD medium and the peristaltic pump was operated in back flush mode with a membrane flux of 1.27 mL min −1 for 1/10 of the filtration time, in this case i.e. 15 min. The back flushed suspension was analyzed by using ATP assay, OD measurement and determination of CFU as described before to determine the bacterial viability of the recovered bacterial cells. The back flushed volume was determined and correlated with the filtration volume of each individual capillary for further calculations. Silver leaching from Ag nano -capillary membranes during filtration was analyzed by determining the silver content of bacteria-free permeate samples via AAS after filtration times of 30 min, 1 h and 2 h, respectively. The filtration conditions (i.e. bacterial feed concentration, buffer, applied flow rate) as well as the length of Ag nano -capillaries were the same compared to the bacterial filtration tests described in Section 2.3.2. For statistical significance three individual capillary membranes were analyzed and permeate samples were collected on three consecutive days where one filtration cycle was performed per day. After each filtration cycle, back flushing was applied for membrane regeneration. For this, capillaries were immersed into fresh OECD medium and the peristaltic pump was operated in back flush mode with a flow rate of 1.27 mL/min for 1/10 of the filtration time (i.e. 12 min). During the time between back flushing and a new filtration cycle the capillaries were held humid and stored at 4°C over night to provide stable conditions. For AAS measurements 100 μL of the permeate samples was immediately acidified after filtration by adding 10 μL HNO 3 (1%) and stored at 4°C. Afterwards, AAS measurements were performed as described in Section 2.2 and untreated capillary membranes served as controls for all experiments. Zirconia capillary membranes were fabricated by extrusion as described in our previous work [30] and functionalized with Ag nano in a straightforward two-step procedure via direct reduction of AgNO 3 on the capillary surface. As shown in Fig. 2A , the presence of Ag nano on the capillary changed the color of the surface from white (non-functionalized capillary made of zirconia) to yellow indicating a homogeneous surface coating. SEM micrographs demonstrate the presence of homogenously distributed Ag nano on the capillary outer surface (Fig. 2C) , whereas the microstructure of the surface of a nonfunctionalized capillary is shown in Fig. 2B . EDX analysis confirmed that the immobilized nanoparticles on the membrane surface consisted of silver (Fig. 2C, inset) . In addition, SEM micrographs of the inner surface of capillaries produced by using 5 mM AgNO 3 and 5 immersion cycles were taken and displayed a similar Ag nano loading ( Supplementary Information, Fig. S1 ). Yielding a high Ag nano loading on the membrane surface, different AgNO 3 concentrations in the range between 2.5 and 10 mM and different numbers of immersion cycles (1, 3, 5 and 10 immersions, respectively) were applied, whereas the incubation time (5 min) and the concentration of the reduction solution NaBH 4 (2 mM) were held constant. For quantification of immobilized Ag nano on the membrane surface, three different methods were employed: manual counting of Ag nano on randomly chosen sections of SEM micrographs, image analysis of SEM micrographs using the software tool "Silver-Particle Analyzer" and atomic absorption spectroscopy (AAS). As shown in Fig. 3A , manual counting revealed that the highest loading capacity of 1702 ± 91 Ag nano per μm 2 capillary was achieved when using a 5 mM AgNO 3 solution in combination with five successional immersion steps, alternating membrane incubation in AgNO 3 solution and in the reduction solution NaBH 4 . In general, regarding one particular AgNO 3 concentration (2.5 mM, 5 mM and 7.5 mM, respectively), increased numbers of immersion steps led to increased numbers of immobilized Ag nano . Compared to an initial AgNO 3 concentration of 2.5 mM, Ag nano -doped membranes fabricated by using 5 mM AgNO 3 showed higher loading capacities by a factor of 1.3 (one immersion), 5.3 (three immersions) and 5.0 (five immersions), respectively. An increase of the AgNO 3 concentration to 7.5 mM did not further increase the Ag nano loading on the membrane and loading capacities were in the same order of magnitude compared to 2.5 mM AgNO 3 . The application of a higher concentration of 10 mM AgNO 3 and 10 immersion cycles led to the undesired formation of agglomerates of immobilized Ag nano , which were inhomogeneously distributed on the capillary surface (data not shown). Providing high Ag nano loadings in combination with a homogeneous membrane surface coating the application of five immersion cycles is the method of choice. Additionally, image analysis software was applied to quantify the particle size distribution of immobilized Ag nano on the membrane surface (Fig. 3B) . Results stood in good correspondence with the results derived from manual counting (Fig. 3A) exhibiting the highest number of Ag nano on capillaries generated by using 5 immersion steps in 5 mM AgNO 3 (Fig. 3B , Supplemental information, Table S1). Silver particle sizes were in the range of approximately 9-35 nm and the average particle diameter for the applied production conditions was calculated to be d 50 = 15 nm (Fig. 3B) indicating that different AgNO 3 concentrations from 2.5 to 7.5 mM lead to similar silver particle sizes and morphologies. Referring to a geometric surface area of 1 mm 2 on Ag nano -capillaries, the active silver surface on the outer and inner surface of the capillary was calculated to allow an assessment of the total silver surface that can interact with the filtrated bacterial cells. For the calculation based on the particle area that was recognized by the analysis software, it was assumed that all Ag nano were spherical and the contact area between the nanoparticles and the capillary surface was negligible. Again, the highest accessible silver surface area of 0.594 mm 2 was present on capillaries treated with 5 mM AgNO 3 , whereas capillaries treated with 2.5 mM and 7.5 mM exhibited a total silver surface of 0.269 and 0.314 mm 2 , respectively. Implicating the density of silver (10.49 g/cm 3 ), total amounts of silver were calculated and capillaries treated with 5 mM AgNO 3 and 5 immersion steps yielded the highest silver loadings of 20 ng per 1 mm 2 geometric surface area ( Table 1) . The two methods, manual counting and software generated particle counts, only consider the Ag nano distribution on the geometric outer and inner surface of the ceramic capillary based on SEM micrographs. The possible penetration of Ag nano into the pores of the membrane material was therefore not considered. With regard to this, we additionally determined the total silver loadings of capillaries treated with 5 mM AgNO 3 by AAS. Using this method, an acidic digestion ensured the total release of silver from the capillaries. With regard to the surface of the pores, the measured amounts of total silver loadings were correlated to the specific surface area of Ag nano -capillaries of 7.05 m 2 /g (Supplemental information, Table S2 ). The obtained AAS results were comparable to the results derived from counting: total Ag nano loadings increased with the number of immersions featuring 0.048 ± 0.001 ng silver/mm 2 specific surface area for 1 immersion, 0.123 ± 0.004 ng silver/mm 2 of capillary specific surface area for 3 immersions and 0.176 ± 0.040 ng silver/mm 2 of capillary specific surface area for 5 immersions (Fig. 4A) . It is noticeable that the calculated amount of bioactive silver based on pixel-generated data of 20 ng per 1 mm 2 geometric surface area was significantly higher than the total amount of silver of 0.18 ng per 1 mm 2 specific surface area that was measured via AAS. The discrepancy of the results can be explained by the different reference membrane areas that were applied. Results from the counting method must be referred to the geometric surface area, since only Ag nano on the outer membrane of the capillaries were considered for the counting. Fig. 4B and C clearly display that Ag nano penetrated to a large extent into the pores of the capillary membrane. For that reason, for the determination of total silver loadings via AAS, the specific surface area determined via nitrogen-adsorption was considered as a reference leading to significantly lower values. Simultaneously, the deep penetration of Ag nano into the pores displays an advantage by enhancing the accessible interaction surface of bactericidal Ag nano and filtrated bacteria. Membrane pore size distributions as well as pore volumes and mechanical properties of untreated and Ag nano -capillaries (5 mM AgNO 3 , 5 immersion steps) were determined by nitrogen adsorption isotherms (BET-BJH evaluation) and bending strength tests (3-point bending test) . Results showed that the additional Ag nano -functionalization did not significantly alter both, the membrane pore sizes and the mechanical properties of the zirconia capillaries [30] providing an efficient filtration performance and good mechanical properties for handling purposes (Supplemental information, Table S2 , Fig. S2 ). Bactericidal properties of Ag nano -capillaries were analyzed by incubating untreated and Ag nano -capillaries in bacterial suspensions of E. coli for 30 min at room temperature. As expected, bacterial growth was only visible close to the untreated capillaries, whereas Ag nanocapillaries prevented the growth of E. coli cells displaying significant bactericidal properties (Fig. 5) . For realistic fresh water filtration conditions the standardized OECD medium was chosen for the preparation of the bacterial feed, since it is used for experiments with the freshwater algae Pseudokirchneriella subcapitata [36] . Filtration of an E. coli suspension was performed in dead-end mode by intracapillary feeding at an initial flow rate of 250 μL/min for 2.5 h using 100 mm capillaries (exhibiting a geometric surface area of 750 mm 2 ) and the resulting permeates of untreated and Ag nano -capillaries were analyzed every 30 min regarding bacterial viability by measuring ATP levels, CFU and OD 595 nm . Results showed highly efficient filtration efficiencies for untreated and Ag nanocapillaries achieving a bacterial retention of nearly 100% which corresponds to a log 10 reduction value (LRV) of 8 (Fig. 6A, B) . No CFUs were detected after plating the permeate samples onto agar plates and ATP and OD 595 nm levels of the permeate samples were comparable to the buffer controls indicating a clear and bacteria-free solution (data not shown). Achieving log 10 reduction levels of N 6, the here presented capillaries accomplish the bacteria filter criterion for safe and clean drinking water according to the U.S. Environmental Protection Agency [37] . Since the membrane flux decreased during filtration, back flushing was induced for membrane regeneration after the filtration of approximately 3 × 10 9 bacterial cells per capillary (750 mm 2 geometric surface area), which corresponds to a filtration time of 2.5 h. Back flushing was applied for 1/10 of the filtration time and filtration efficiencies were recovered by reaching 95-100% of the initial membrane flux (Fig. 6A, B) . Since both, untreated and Ag nano -capillaries, featured similar filtration properties, the assumed benefit of the Ag nano -immobilization is the inhibition of the initial attachment of living bacteria [38, 39] to the capillary surface and the inhibition of initial biofilm formation. In general, after initial attachment, bacteria start to secrete extracellular polymeric substances providing a matrix for other bacteria to embed and build a biofilm [40] . This biofilm leads to pore blocking which is followed by an increase of the transmembrane pressure and operating time leading to lower filtration efficiencies. Creating a strong bactericidal surface by using an Ag nano coating, bacteria are assumed to die when coming into contact with the capillary membrane before the expression of biofilm components will be initiated and dead bacteria will be removed by operating the pump in back flush mode [41] . To analyze the viability of the retained bacteria, the recovered bacteria from back flushing were analyzed regarding ATP levels and CFU. Table 1 Accessible silver surface area and total amount of immobilized silver on 1 mm 2 geometric surface area of Ag nano -capillaries. Conditions for the immobilization of silver nanoparticles Unfortunately, bacteria that were recovered from Ag nano -capillaries during back flushing after 150 min filtration were found to be viable as measured by ATP levels and CFU. The amount of filtrated bacteria was probably too high so that the contact of bacterial cells with the bactericidal Ag nano surface could not be assured (data not shown). Therefore, individual Ag nano -capillaries were tested for filtration times of 30, 60, 90, 120 and 150 min to identify the maximum filtration time that ensured the death of retained bacteria. Back flushing after 30 min and 60 min filtration time showed that recovered E. coli cells from Ag nano -capillaries were dead displaying marginal bacterial ATP levels of 3.4 and 1.6% in comparison to reference bacteria that were recovered from untreated capillaries (Fig. 6C ). Capillaries that were used for longer filtration times of N60 min were not capable in killing bacterial cells at the inner membrane surface of the capillaries as shown by determined ATP levels (Fig. 6C ). Back flushing of Ag nano -capillaries should therefore be initiated after a maximum filtration time of 60 min, corresponding to a bacterial load of 6 × 10 8 bacterial cells/ 750 mm 2 geometric capillary surface area. Understanding the stability of each individual bactericidal Ag nano membrane coating, Ag nano -capillary membranes were tested for five consecutive filtration cycles of 60 min each, while back flushing was initiated after each cycle. Microbiological results showed that bacterial viability was decreased to 2-5% in relation to the reference bacteria that were recovered from untreated capillary membranes as analyzed by ATP levels and CFU indicating a stable bactericidal membrane surface at suitable filtration times of 60 min (Fig. 6D) . Similar results were obtained by Liu et al. [20] showing that a silvernanoparticle-decorated polysulfone membranes exhibited anti-adhesive properties in comparison to unfunctionalized polysulfone membranes. Although the authors reported similar retention rates for unfunctionalized and silver-functionalized polysulfone membranes, significantly more bacteria were detached during rinsing experiments from the silver-decorated membranes than from untreated membranes. However, our back flushing results (Fig. 6C ) also showed that longer filtration times N 60 min were not recommendable, since bacterial killing was not ensured anymore. The bacterial filter cake was probably too thick to allow a contact-induced killing of bacteria by Ag nano . Silver contamination of water is an environmental predicament. Since silver is proved to be toxic against several freshwater organisms such as Daphnia magna [42] and may lead to safety concerns [43] , its release into the environment needs to be accurately monitored. Thus, the release of silver from the Ag nano -capillaries during filtration and silver maximum contaminant levels were determined. Therefore, samples from the filtrated permeates of three individual capillaries were removed after 30 min, 60 min and 120 min of filtration on three consecutive days and analyzed by AAS. AAS measurements revealed that the silver release was highest at the beginning of the filtration on each individual day. After the first burst release after 30 min of filtration on the first day where 400 ± 3 μg/L of silver was released, silver leaching progressively decreased reaching values of 34 ± 0 μg/L already after 60 min of filtration and only 21 ± 17 μg/L at the last measurement after 420 min of filtration (Fig. 7) . Among the filtration cycles, capillaries were stored under humid conditions at 4°C overnight until filtration was started again. The storage induced a continuous release of silver from the capillary, which was then released at the following filtration cycles, which explains the recurring increases of silver release in the beginning of each filtration cycle. High standard deviations result from the phenomenon that small pieces of the capillaries got lost and were measured in the permeate samples. The maximum contaminant level for silver in drinking water is 50 μg/L as set by the World Health Organization (WHO), whereas "under special situations where silver salts are used to maintain the bacteriological quality of drinking-water higher levels of up to 100 μg/L can be tolerated without risk to health" [44] . Although silver was continuously released during filtration, WHO requirements were fulfilled already after 1 h of filtration when silver contaminant levels of 34 ± 0 μg/L were reached. In addition to the eco-toxicological aspect, the loss of the bactericidal coating displays a drawback, because it reduces the operating time and requires a frequent replacement of the coating or the complete membrane. Total silver loading capacities of Ag nano -capillaries of 411.64 ± 94.88 μg silver/100 mm capillary were determined by AAS. The filtration experiment showed that 0.23 ± 0.05% of the initial silver loading was released after the first 30 min of filtration and amounts of 0.01 ± 0.05% were released after 420 min of filtration on the third day. The total silver release during the three-day experiment was determined to be 0.81 ± 0.43% of the initial silver content that was immobilized on each capillary displaying a very good stability of the bactericidal Ag nano coating. Leaching of immobilized silver has also been demonstrated by Chou et al. [45] who analyzed the stability of an Ag nano coating on cellulose acetate hollow fiber membranes. A 180 day static immersion in water decreased the silver content on the membrane surface by 90%, but still an antibacterial effect against E. coli and Staphylococcus aureus was evident. In contrast, after permeating with water for 5 days, a significant higher and faster loss of silver was determined and no antibacterial effect was measurable anymore. Other studies also reported rapid depletions of silver from membrane surfaces after relatively short filtration periods (0.4 L/cm 2 ) and the soon loss of antibacterial and antiviral activities [6] . The here presented capillaries were capable of killing bacteria during filtration for at least five consecutive filtration cycles of 60 min and the silver release from the membrane after the first 30 min of filtration fulfilled the requirements on eco-toxicological demands. Porous ceramic capillaries made of zirconia were functionalized with broadband bactericidal Ag nano for utilization as small-sized water purification modules exhibiting durable antibacterial properties. The immobilization of Ag nano was performed via direct reduction of silver nitrate to metallic Ag nano on the surface of the capillaries. This straightforward procedure led to high silver loadings of up to 1700 Ag nano per μm 2 capillary surface when using 5 mM AgNO 3 and 5 immersion cycles and could also be transferred to other oxide and non-oxide ceramics, such as aluminum oxide or silicon carbide. Total silver loadings as determined by AAS were found to be 0.18 ng silver per 1 mm 2 specific surface area and 20 ng silver per 1 mm 2 geometric surface area as calculated based on nanoparticle-covered membrane surface areas. Zirconia capillaries exhibited excellent filtration performances obtaining bacterial retention rates of log 10 reduction values of 8. Back flushing cycles of 1/10 of the filtration time were suggested for membrane regeneration leading to regained filtration efficiencies of 95-100%. Creating a strong bactericidal surface, immobilized Ag nano on the zirconia surface efficiently killed bacteria during filtration for filtration times of up to 60 min corresponding to 6 × 10 8 filtrated bacterial cells/750 mm 2 capillary surface. A subsequent back flushing cycle ensured the removal of dead cells from the membrane surface leading to the regeneration of filtration efficiencies and allowed the application for consecutive filtration cycles. Release of silver during filtration was analyzed and was moderate leading to silver contaminant levels of 34 μg/L after 1 h of filtration (250 μL/min). Displaying strong bactericidal properties, the described ceramic-silver composite might be beneficial for several disinfection strategies, for example when applied for the coating of medical devices or for areas in which germ-free surfaces are necessary. Escherichia coli biofilms Point of use water treatment with forward osmosis for emergency relief Potential of silver nanoparticle-coated polyurethane foam as an antibacterial water filter Patent: Combinations of liquid filtration media and methods for enhanced filtration of selected water contaminants Modification of membrane surface for anti-biofouling performance: effect of anti-adhesion and anti-bacteria approaches Polysulfone ultrafiltration membranes impregnated with silver nanoparticles show improved biofouling resistance and virus removal Preparation, characterization, and antibacterial properties of electrospun polyacrylonitrile fibrous membranes containing silver nanoparticles Organic fouling behavior of superhydrophilic polyvinylidene fluoride (PVDF) ultrafiltration membranes functionalized with surface-tailored nanoparticles: implications for organic fouling in membrane bioreactors Recent development in additives modifications of polyethersulfone membrane for flux enhancement Ceramic filters and membranes High virus retention mediated by zirconia microtubes with tailored porosity Antibacterial and abrasion-resistant alumina micropatterns Structure-related antibacterial activity of a titanium nanostructured surface fabricated by glancing angle sputter deposition Effect of biomediated route synthesized silver nanoparticles for modification of polyethersulfone membranes Silver as antibacterial agent: ion, nanoparticle, and metal Silver enhances antibiotic activity against Gram-negative bacteria Silver-PEGylated dendrimer nanocomposite coating for anti-fouling thin film composite membranes for water treatment Proteomic analysis of the mode of antibacterial action of silver nanoparticles Silver and its application as an antimicrobial agent Direct observation of bacterial deposition on and detachment from nanocomposite membranes embedded with silver nanoparticles Evaluating the antifouling effects of silver nanoparticles regenerated by TiO 2 on forward osmosis membrane Antimicrobial activity of highly stable silver nanoparticles embedded in agar-agar matrix as a thin film Effect of calcination on microstructure and antibacterial activity of silver-containing silica coatings The production of polysulfone (PS) membrane with silver nanoparticles (AgNP): physical properties, filtration performances, and biofouling resistances of membranes Silver contents in the permeate samples of three individual capillaries of 100 mm lengths were analyzed using AAS to determine the silver release from the Ag nano -capillaries. For this, permeate samples were removed after 30 min, 60 min and 120 min of filtration on three consecutive days Polyethersulfone (PES)-silver composite UF membrane: effect of silver loading and PVP molecular weight on membrane morphology and antibacterial activity Effect of silver loaded sodium zirconium phosphate (nanoAgZ) nanoparticles incorporation on PES membrane performance Effect of silver nanoparticle (AgNP) location in nanocomposite membrane matrix fabricated with different polymer type on antibacterial mechanism Silver as biocides in burn and wound dressings and bacterial resistance to silver compounds Silver nanoparticle-decorated porous ceramic composite for water treatment Development and characterisation of functionalised ceramic microtubes for bacteria filtration Plasma resonance enhancement of Raman-scattering by pyridine adsorbed on silver or gold sol particles of size comparable to the excitation wavelength Comments on A Scientific and Animal Welfare Assessment of the OECD Health Effects Test Guidelines for the Safety Testing of Chemicals under the European Union REACH System Biotechnology II: Global Prospects The nephelometer: an instrument for estimating the numbers of bacteria in suspensions used for calculating the opsonic index and for vaccines Bactericidal effect of silver nanoparticles against multidrug-resistant bacteria Toxicity of nanoparticles of CuO, ZnO and TiO 2 to microalgae Pseudokirchneriella subcapitata Safe Drinking Water Act Antibacterial surfaces: the quest for a new generation of biomaterials Silver nanoparticles with anti microfouling effect: a study against marine biofilm forming bacteria The EPS matrix: the "house of biofilm cells Development and testing of a fully adaptable membrane bioreactor fouling model for a sidestream configuration system Toxicity of various silver nanoparticles compared to silver ions in Daphnia magna The use of nanoparticles in polymeric and ceramic membrane structures: review of manufacturing procedures and performance improvement for water treatment Guideline for Drinking-water Quality -Silver in Drinking water The preparation and characterization of silver-loading cellulose acetate hollow fiber membrane for water treatment Financial support from the Federal Ministry of Education and Research (BMBF, support code 0315520) is gratefully acknowledged. We thank Petra Witte (University of Bremen, Department of Geosciences) for her support with the SEM. Supplementary data to this article can be found online at http://dx. doi.org/10.1016/j.msec.2014.12.001.