key: cord-0914985-10bv3ioh
authors: Berg, Michael G; Israeli, Eitan; Quaco, Erin; Cloherty, Gavin A; Hemken, Philip M
title: Tergitol-15-S-9 inactivates SARS-CoV-2 and boosts immunoassay signals
date: 2021-06-18
journal: BioTechniques
DOI: 10.2144/btn-2021-0044
sha: 884592cdfc1a05467253d15fc03d302c8df5bbf1
doc_id: 914985
cord_uid: 10bv3ioh

Inactivation of SARS-CoV-2 virus is necessary to mitigate risk but may interfere with diagnostic assay performance. We examined the effect of heat inactivation on a prototype SARS-CoV-2 antigen immunoassay run on the ARCHITECT automated analyzer. Recombinant full-length SARS-CoV-2 nucleocapsid protein and virus lysate detection was reduced by 66 and 31%, respectively. Several nonionic detergents were assessed as inactivation alternatives based on infectivity in cultured Vero CCL81 cells. Incubation of SARS-CoV-2 in 0.1% Tergitol 15-S-9 for 10 min significantly reduced infectivity and increased the immunoassay signal for cultured lysate and patient specimens. Tergitol 15-S-9 can inactivate SARS-CoV-2 while preserving epitopes on the nucleocapsid protein for enhanced detection by immunoassay antibodies.

Treatment of SARS-CoV-2 virus lysate or patient specimens in viral transport medium with 0.1-0.5% Tergitol 15-S-9 for 10 min inactivates the virus, as measured by infectivity in cell culture, and does not interfere with detection of the SARS-CoV-2 nucleocapsid by a prototype nucleocapsid antigen immunoassay run on the automated ARCHITECT platform.

Handling of active cultures of highly infectious viruses, such as SARS, MERS and SARS-CoV-2, must be conducted in a biosafety level 3 (BSL-3) laboratory [1] . Inactivation of the virus in patient specimens can reduce infectivity and mitigate risk to lab personnel [2] . Previous studies of SARS reported effective inactivation with heat, UV irradiation and solvent/detergents such as Triton X-100, Tween 80 and sodium cholate [3] . Ideally, virus inactivation should occur in the transport media for biological specimens; however, recent studies of SARS-CoV-2 inactivation have reported that some methods and reagents may interfere with diagnostic assay performance [4] . Certain salts [5] and heat inactivation protocols [6] have been shown to reduce the accuracy of molecular assays, whereas heat inactivation of patient specimens was shown to reduce the amount of anti-SARS-CoV-2 IgG and IgM detected by fluorescence immunochromatography [7] , but not by ELISA [8] .

SARS-CoV-2 antigen tests are immunoassays useful for the diagnosis of COVID-19, with test results prompting further molecular testing, quarantine, contact tracing and treatment [9] . Several SARS-CoV-2 antigen assays are currently approved under emergency use authorization [10] to detect specific SARS-CoV-2 antigens in nasopharyngeal or nasal swab specimens. Few studies have examined whether viral inactivation methods affect SARS-CoV-2 antigen assay performance. Here, we evaluated the effect of SARS-CoV-2 inactivation on virus infectivity in cell culture and detection by a prototype SARS-CoV-2 antigen immunoassay run on the ARCHITECT automated analyzer (Abbott Laboratories, IL, USA).

A prototype sandwich immunoassay specific for the SARS-CoV/SARS-CoV-2 nucleocapsid antigen was developed on the Abbott ARCHI-TECT automated immunoassay analyzer. In this immunoassay, paramagnetic microparticles coated with a mouse monoclonal antibody serves as the solid phase reagent for capturing the viral nucleocapsid target. Some results obtained with Abbott's ARCHITECT prototype sandwich immunoassay involved the use of a monoclonal antibody against SARS-CoV provided by the National Institute of Infectious Diseases in Japan. The captured antigen is detected with a mouse monoclonal antibody conjugated with acridinium, which produces a chemiluminescent signal upon target binding, with signal quantified in relative light units (RLU).

Recombinant full-length nucleocapsid protein at calibrator levels was gravimetrically prepared in calibrator diluent (Cal Dil) consisting of HEPES 50 mM pH 7.2-7.4, NaCl 150 mM, 1% Tergitol 15-S-40 and protease-free 1% bovine serum albumin (BSA). Stock virus lysate (USA-WA1-2020 strain, GenBank accession MN985325.1) was obtained from BEI Resources (VA, USA; established by NIAID and managed by American Type Culture Collection to provide emerging infectious disease agents to the research community; NR-52281, lot# 70036318, TCID 50 of 1.6 × 10 6 per ml) and diluted in viral transport medium (VTM; HBSS 1X, HI-FBS 2%, Amphotericin B 0.5 μg/ml and Gentamicin 100 μg/ml). For detergent inactivation experiments, BEI stock virus lysate was diluted in a base VTM diluent (10 mM phosphate-buffered saline, 2% BSA protease-free, 0.1% ProClin 300 and 10 ppm antifoam). Residual deidentified patient specimens in VTM were obtained from New York Biologics (NY, USA) and generation of Abbott high-titer calibrator stocks of SARS-CoV-2 was performed as described 

Recombinant full-length SARS-CoV-2 nucleocapsid protein was diluted then heat inactivated at 65 • C for 30 min. Stock virus lysate was inactivated at 60 • C for 90 min in a BSL-3 lab before dilution in VTM, then heat inactivated again at 65 • C for 30 min. Patient specimens in VTM had been previously heat inactivated at 65 • C for 30 min for molecular testing on the Abbott m2000 platform.

Tergitol 15-S-9, Tergitol 15-S-40, BrijL23, Tween-80, Tween-20, Surfynol 465, line diluent and blends of these nonionic detergents were combined with stock SARS-CoV-2 lysate (BEI NR-52281, lot# 70036318, TCID 50 of 1.6 × 10 6 per ml). Virus lysate in VTM (∼10 8 cp in 100 μl) was mixed 1:1 v/v with 100 μl VTM (no detergent control) or 100 μl of various detergents and blends to achieve a final detergent concentration of 0.1-0.5%. The mixtures were incubated at room temperature for 10, 20 or 30 min.

Vero CCL81 cells (3 × 10 5 cells) were plated in a 96-well format the night before infection. Virus/detergent mixtures were applied to cultured Vero CCL81 cells for 2 h. In initial experiments, we found that above 0.0025%, some individual detergents or blends were toxic to Vero CCL81 cells after the 2-h incubation (data not shown). To reduce toxicity to cells, after the detergent inactivation period and immediately before infection, the virus/detergent mixtures were diluted in DMEM media lacking fetal bovine serum (FBS) (DMEM + penicillin/streptomycin [P/S]) to a final detergent concentration of ≤0.0025%. The diluted mixtures were applied to the cells and incubated for 2 h. Cells were then washed with PBS, placed in 100 μl complete media (DMEM + P/S + 10% FBS), and incubated for ≥96 h before assessment of infectivity by Viral Tox Glo assay.

Cells were monitored by microscopy and cytopathic effects (CPE) were quantitatively measured using the Viral with 100 μl of Viral Tox Glo substrate and incubated for 5 min away from light. Luminescence was measured on a GloMax Navigator (Promega).

Control (2-8 • C) and heated dilutions of nucleocapsid protein and virus lysate were run on the prototype ARCHITECT immunoassay. Heat inactivation reduced the assay signal an average of 66% for the recombinant nucleocapsid dilutions and 31% for the viral lysate dilutions (Table 1) .

To avoid the significant loss of signal on the prototype ARCHITECT immunoassay following heat inactivation, we examined the use of detergent as an alternative approach to SARS-CoV-2 inactivation. Tergitol 15-S-9 alone and Tergitol 15-S-9 + Surfynol 465 at 0.1% concentration were able to inactivate the virus within 10 min; Tergitol + Tween-20 required 30 min (Figure 1 ). The other detergents tested (Tergitol 15-S-40, Tween-20, Tween-80, Surfynol 465, and line diluent) displayed no effect on viral infectivity at 0.1% (Figure 1 ). Virus inactivation was repeated at a higher detergent concentration (0.5% final), which confirmed the results at 0.1% and additionally showed that the detergent Brij-L23 can inactivate SARS-CoV-2 when incubated for ≥20 min (data not shown). Two different strains of SARS-CoV-2 were evaluated to confirm Tergitol 15-S-9 inactivation of the virus at 0.5% and 0.1%, but not at 0.01% (data not shown). To determine the optimal concentration of Tergitol 15-S-9 for inactivation, a dilution series was performed with concentrations ranging from 0.01%-0.5% with a 10 min incubation. We observed inactivation with Tergitol 15-S-9 at concentrations from 0.5% to 0.1% (Figure 2 ). At 0.05%, only one of the two replicates showed evidence of CPE, while at 0.01% there was no inactivation and both cell culture wells were heavily infected, similar to the no detergent controls (0.0%).

To assess the effects of increasing amounts of Tergitol 15-S-9 on the SARS-CoV-2 antigen signal in the prototype ARCHITECT immunoassay, virus lysate was inactivated with increasing concentrations of Tergitol 15-S-9 (0.1 -0.5%) diluted in base VTM diluent. Each condition Vol. 71 No. 1 C 2021 Abbott Laboratories www.BioTechniques.com was run in triplicate. Inactivation of the virus in VTM with 0.1%-0.5% Tergitol 15-S-9 significantly increased the immunoassay signal an average of 151% to 176%, with the highest RLUs seen with 0.3%-0.4% Tergitol 15-S-9 (Table 2) . We then tested the effect of inactivating virus in patient specimens with 0.1%-0.4% Tergitol 15-S-9 in VTM on detection in the prototype ARCHITECT immunoassay. As with the stock virus lysate, positive patient specimens inactivated in 0.1%-0.4% Tergitol 15-S-9 had significantly higher immunoassay signal compared to VTM control (Table 3) . Negative patient specimens remained unchanged. Thus, treatment of stock SARS-CoV-2 lysate and patient specimens with 0.1% Tergitol 15-D-9 for 10 min not only inactivated the virus, but also increased the signal in the ARCHITECT prototype immunoassay.

SARS-CoV-2 heat inactivation requires 30 min and reduces immunoassay sensitivity. Tergitol 15-S-9 is a simple additive to VTM that can inactivate virus in 10 min while allowing improved detection by the ARCHITECT prototype sandwich immunoassay. A mid-range concentration of 0.2% Tergitol 15-S-9 for 10 min was selected for subsequent assay optimization. Tergitol 15-S-9 may preserve secondary/tertiary protein structures that heat inactivation destroys. We also found that Tergitol 15-S-9 increased the RLU signal in the ARCHITECT prototype sandwich immunoassay for SARS-CoV/SARS-CoV-2, suggesting that it may expose epitopes for enhanced detection by the immunoassay antibodies.

Future studies will need to examine whether Tergitol 15-S-9 affects other SARS-CoV-2 diagnostic assays, including molecular assays and rapid antigen tests.

• We determined the effect of different methods of SARS-CoV-2 inactivation on 1) virus infectivity in cell culture and 2) detection of the nucleocapsid antigen by a prototype SARS-CoV-2 immunoassay run on the ARCHITECT automated analyzer.

• Recombinant SARS-CoV-2 nucleocapsid antigen, stock virus lysate, and infected patient specimens were inactivated with heat and/or various types and combinations of detergents. • The effect of inactivation was determined on infectivity of the virus in cultured Vero CCL81 cells measured by Viral Tox Glo assay and on detection of the nucleocapsid antigen by the prototype immunoassay.

• Heat inactivation reduced the immunoassay signal an average of 66% for the recombinant nucleocapsid and 31% for viral lysate.

• Tergitol 15-S-9 was able to inactivate the virus within 10 min.

• Tergitol 15-S-9 increased the immunoassay signal an average of 151% to 176% in viral lysate and 309% to 500% in patient specimens.

• Tergitol 15-S-9 is a simple additive to viral transport media that can inactivate SARS-CoV-2 while preserving epitopes on the nucleocapsid protein for enhanced detection by immunoassay antibodies.

MG Berg planned and executed experiments and wrote the manuscript; E Israeli planned and executed experiments and wrote the manuscript; E Quaco executed experiments; GA Cloherty reviewed the manuscript; PM Hemken planned and executed experiments and wrote the manuscript. All authors reviewed and approved the manuscript for submission.

This study was funded by Abbott Laboratories. All authors are employees of Abbott Laboratories. A patent application has been filed for the described method. The authors have no other relevant affiliations or financial involvement with any organization or entity with a financial interest in or financial conflict with the subject matter or materials discussed in the manuscript apart from those disclosed. We acknowledge Stacey Tobin for scientific writing assistance of this manuscript.

Centers for Disease Control and Prevention. Interim Laboratory Biosafety Guidelines for Handling and Processing Specimens Associated with Coronavirus Disease

Inactivation of the coronavirus that induces severe acute respiratory syndrome, SARS-CoV

Evaluation of inactivation methods for severe acute respiratory syndrome coronavirus in noncellular blood products

Laboratory testing of SARS-CoV, MERS-CoV, and SARS-CoV-2 (2019-nCoV): current status, challenges, and countermeasures

Centers for Disease Control and Prevention. Interim Guidelines for Collecting and Handling of Clinical Specimens for COVID-19 Testing

Heat inactivation of different types of SARS-CoV-2 samples: what protocols for biosafety, molecular detection and serological diagnostics?

• This study reported the potential adverse effects of heat inactivation on SARS-CoV-2 diagnostic assay performance

Impact of heat-inactivation on the detection of SARS-CoV-2 IgM and IgG antibody by ELISA

Centers for Disease Control and Prevention. Interim Guidance for Antigen Testing for SARS