key: cord-0875136-qv3x82kr
authors: Kamble, Pushkar; Mittal, Yash G.; Gote, Gopal; Hodgir, Rajendra; Karunakaran, K. P.
title: COVID Key: A Multifunctional Device to Avoid Touch
date: 2021-07-09
journal: Trans Indian Natl
DOI: 10.1007/s41403-021-00250-x
sha: 2b374f40a03b72206cb0f685bd0c1f571ca50330
doc_id: 875136
cord_uid: qv3x82kr

COVID-19 is a global pandemic caused by the novel coronavirus. Although the surfaces pose a low risk of transmission, it is beneficial to use a handheld key-like device to avoid touching the surfaces, especially in public places. The present article reveals a novel design for a multifunctional handheld device, termed the COVID key. The proposed COVID key exhibits ten distinct features, viz. doorknob opener, pushing, pulling, forceps action, sharp edge, key chain, smartphone stand, and a linear and angular scale frequently used in daily life. Theoretical and computational analyses are carried out to check the validity of the design under different loading conditions resembling everyday use. Topological optimization is carried out to achieve the best stiffness-to-weight ratio. The final design is 3D printed in two different materials, ABS (acrylonitrile–butadiene–styrene) and PLA (poly-lactic-acid), using fused deposition based additive manufacturing. Testing and validation of the design are carried out with everyday actions. The COVID keys are distributed among a group of ten unbiased users. The user satisfaction score is recorded based on six basic metrics, viz. ease of use, size, strength, appearance, material and ease of carrying. A satisfaction score of 85% is reported, with ABS being the preferred material of choice.

First reported in Wuhan, China, in late 2019, COVID-19 is a global pandemic now. The virus that causes COVID-19 belongs to a group of zoonotic viruses termed coronavirus. The present virus responsible for COVID-19 is termed severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) (Wang et al. 2020) . The virus transmission occurs through respiratory droplets of saliva and sputum generated while speaking, coughing, and sneezing (WHO 2020). The droplets generated from sneezing travel a longer distance of 7-8 m (Bourouiba 2020) . When they fall on the surfaces, the drying time of the droplets varies from 5 to 70 s on various surfaces under various conditions (Bhardwaj and Agrawal 2020) . Infected surfaces, therefore, is an indirect route of transmission (WHO 2020). If a person touches the surfaces with the active virus by hands and then touches their ophthalmic or nasal mucosae, the infection gets transmitted. Although it is recently found that transmission from contaminated surfaces in the public setting is low, it is important to avoid direct contact with the surfaces at specific locations with a high number of individuals living with COVID-19, such as hospitals and quarantine centres. One solution for this problem is to use a handheld device that helps perform various actions involving a direct touch of the surfaces.

Several devices were recently launched in the market, colloquially known as "COVID Key" or "COVID Key Chain". The detailed survey of the existing designs of the keys reveals a universal form of the key, as shown in Fig. 1 . There are several other actions that the available keys do not provide, such as rotation of the taps, bottle opener, holding currency notes, etc. For these actions, a key is required that incorporates most of the day-to-day activities involving touch. In the present article, a handheld key-like device is proposed for various actions such as pinching, pulling, rotating, etc. The detailed use of the device is discussed subsequently. The size and shape of the key can be customized to suit the individual ergonomic needs. Hence, 3D printing is the most suitable route for mass customized production.

Various actions that involve touching the surfaces are pinching, pulling, pushing, rotating, and lifting. Pinching action is required while handling thin objects such as papers, * Pushkar Kamble pushkarkamble@gmail.com 1 Indian Institute of Technology Bombay, Powai, Mumbai 400076, India plastic sheets, and currency notes. Since many people handle the currency and majority of papers in the office setting, it increases the transmission risk. A heavy number of people commonly touches door handles. Keeping the doors always open could be one solution, but that may not be an option in the rooms with an air conditioner or air purifiers. Thus, pulling the handles of the door, drawers, trolleys pose a greater risk of transmission. Pushing is another action essentially performed with doors, windows, chairs, etc. Rotation/Gyration is an action performed while opening/closing the taps, knobs of the electrical instrument, opening the threaded bottle caps. Lifting objects such as plastic bags, etc., is another common action performed in the social setting, especially at the supermarkets. All the actions mentioned above increase the touching of surfaces repeatedly. A handheld device that can assist in avoiding the repeated touching of the surfaces at public places is a prime need in environments with active contagions. In these actions mentioned above, the ergonomics of the action is crucial to notice. The key needs to have a firm grip by hand and sufficiently rigid to sustain the loads generated by the actions. The design of the key for different functions is discussed in the subsequent sections.

The proposed COVID key is designed with a minimalistic design and maximum features approach (Fig. 2) . The overall length and breadth of the key are limited to 117 mm and 50 mm, respectively, and the thickness is set to 10 mm to avoid discomfort while carrying it in the pocket.

The design parameters are selected to provide multiple distinct features for everyday use. A wide strut is provided at the front of the key for pushing operations, such as pressing the elevator buttons (Fig. 2) . A thin, flexible narrow strut accompanying the main strut enables the forceps-like action to pick up papers or currency notes. Facial masks act as a barrier to protect the nose and mouth, reducing the probability of contacting the virus. Handling the outside of the facial masks with bare hands is not recommended. The forcepslike feature of the proposed COVID key helps remove or temporary lowering face masks.

The proposed COVID key has graduation marks on the lateral side for linear measurements up to 30 mm with the least count of 5 mm. Additionally, the circular surface has graduation marks for angular measurements up to 360° at intervals of 30°. The hole is made hexagonal to enable the wrench-like feature to tighten/loosen the hex bolts. The hole is made finger-sized that enables a good grip for holding the key between fingers. A smaller hole near the wrench feature helps fasten the car keys. The sharp edge helps tear and screw operations. Below the struts, there is a perpendicular arm with a notch that acts as a bottle opener. The other side of this arm can be used for pulling/lifting actions. Near to this arm is a circular grip for holding and operating doorknobs or circular headed taps. A thin, flexible element is present besides the grip makes it adjustable. Figure 2 shows the CAD (computer-aided design) model of the proposed design along with a labelled diagram highlighting different dimensions and features.

Different structural analyses followed by computational (FEA) evaluation are performed under static loading conditions on the various features presented in the COVID key design. The designed object is considered a solid body, following linear isotropic behaviour and uniform loading conditions. The design is made for an upper limit of 100 N, set as the average human values of force (Nilsen et al. 2012) . The design and FEA validation are done using SOLID-WORKS 2019 Educational License. The final design is 3D printed using the fused deposition modelling (FDM) technique. ABS and PLA are some of the most commonly used materials for FDM 3D printing (Mazzanti et al. 2019) . In this work, a functional prototype is analyzed and fabricated using both materials.

The wide strut is used for pushing actions, undergoing buckling conditions. Euler's theory of buckling is applied with the following assumptions (Stephen and Timoshenko 1961): 1. The column is initially perfectly straight and is axially loaded, with a maximum force of 100 N. 2. The section of the column is uniform. The end curvature effect of fillets is neglected. 3. The column is perfectly elastic, homogeneous and isotropic and obeys Hooke's Law. 4. The column length (L = 30 mm) is substantial compared to the lateral dimensions (6 mm × 10 mm). 5. The direct stress is minimal compared with the bending stress corresponding to the buckling condition. 6. The self-weight of the column is neglected. 7. The column is failing by buckling only.

A fixed-free buckling condition is employed for the case. The slenderness ratio ( ) is calculated using the relation mentioned in Eq. (1)as follows:

where L e is the effective length of the column (= 2L, for fixed-free condition) and r k is the radius of gyration corresponding to the critical area moment of inertia ( r k = √ I A ; I = d.b 3 12 ; b = 6 mm (width), d = 10 mm (depth); A is the crosssectional area of the column). The slenderness ratio comes out to be 34.62, referring to an intermediate column buckling condition. The corresponding critical buckling load ( P cr ) is calculated using Eq. 2 as fpllows:

where E is the modulus of linear elasticity for ABS (2.5 GPa (Vácha and Borůvka 2015) ) and PLA (2.78 GPa (Wittbrodt and Pearce 2015) ), The corresponding critical buckling loads ( P cr ) are 1.26 kN and 1.4 kN for ABS and PLA, respectively. The critical buckling loads hugely surpass the maximum applied axial load, indicating that design is safe under buckling condition for both the materials, as follows: FEA validation is done by fixing the nearest flat face parallel to the cross-section in the hexagonal wrench region. A direct axial compressive load of 100 N is applied on the face of the wide strut, as shown in Fig. 3a .

The study consisted of solid mesh, single-mode, FFE-Plus buckling analysis with zero strain temperature as 298 K. ABS material with a linear elastic isotropic model is selected from the software database, with the material properties as mentioned in Table 1 . PLA material is not available in the database. It is inserted as a new material with the required mechanical properties defined, also mentioned in Table 1 .

The solid mesh type is used. The element size and tolerance are 2.45535 mm and 0.122768 mm, respectively. The mesh quality plot is set to high, and the meshed profile is shown in Fig. 3b . The total number of nodes and elements formed are 25,053 and 14,715, respectively, with the maximum aspect ratio of 20.14. Almost 87% of elements have an aspect ratio less than 3, and around 0.2% of elements have an aspect ratio greater than 10. The same set of computational environments is applied to every simulation.

The result of the buckling analysis shows the amplitude plot, with a maximum amplitude of 0.025 for both the cases as depicted in Fig. 3c and d. The similarity in

(3) P cr (1260 (ABS), 1400 (PLA)) > P applied (100 N) the amplitude for both the materials can be attributed to the fact that the applied load is much less than the critical buckling load for both cases.

Under a similar set of conditions, a uniaxial compression analysis is also done. The maximum Von-Mises stress developed in the strut for ABS and PLA is 1.55 MPa 6.245 MPa respectively ( Fig. 4a and b) . The factor of safety for ABS and PLA is 19.35 and 8.65 respectively. The corresponding freeend deflection and maximum strain for ABS are 0.4628 mm and 1.094 × 10 −3 mm/mm respectively, as shown in Fig. 4c and e. For PLA, it is 0.3337 mm and 1.401 × 10 −3 mm/mm, respectively ( Fig. 4d and f). 

The COVID key design presents various features that undergo direct or indirect bending, for example, flexion of the narrow strut for forceps feature, bottle-cap opening action, pulling action using the rear side of the bottle opener, bending of the thin flexural arm near the hexagonal wrench feature, for the doorknob action. All the bending conditions are cantilevers, and Euler-Bernoulli beam bending theory is applied with the following assumptions (Richard and Budynas 2011):

1. The material of the beam is homogeneous and isotropic.

2. The value of Young's Modulus of Elasticity is the same in tension and compression. 3. The transverse sections, which were plane before bending, remain plane after bending also. 4. The beam is initially straight, and all longitudinal filaments bend into circular arcs with a common centre of curvature. 5. The radius of curvature is large as compared to the dimensions of the cross-section. The effect of end-fillets and stress concentrations is also neglected. 6. Each layer of the beam is free to expand or contract, independently of the layer above or below it.

The narrow strut can be pushed down to hold delicate features like paper, laminates, and coins. As mentioned earlier, it can also be used to temporarily lower the face mask as and when needed without using the fingers, enhancing the health and safety of the user. The clearance between the struts restricts the maximum deflection ( ) up to 2 mm only. Assuming the Euler-Bernoulli cantilever beam bending, the load (P) required to generate this amount of deflection can be calculated using Eq. (4).

The length of the section (L) is considered to be 30 mm, and the moment of inertia (I) is calculated for the rectangular section (I = d.b 3 12 ; b = w mm (width), d = 10 mm (depth)). With E b as the bending modulus (2.10 GPa for ABS (Stephen and Timoshenko 1961) and 0.973 GPa for PLA (Abeykoon et al. 2020) ), the lateral load required is 2.711 N for ABS and 1.256 N for PLA. The corresponding bending stresses for ABS and PLA are 12.19 MPa and 5.67 MPa, respectively, which are significantly less than the tensile strength of the respective materials, indicating that the deflection is in elastic range and the narrow strut is going to restore to its original position once the load is removed, for both the materials.

Validation of the design feature based on the above bending analysis is done using FEA. The rear face of the COVID key is treated as a fixture, and an axially perpendicular load of roughly 3 N for ABS and 1.26 N for PLA is applied at the free end of the narrow strut.

The free tip of the narrow strut is showing a deflection of 2.188 mm for ABS and 1.943 mm for PLA ( Fig. 5a and b) and the maximum bending stress detected is 14.31 MPa (ABS) and 6.12 MPa (PLA), at the fixed end. Compared with the analytical solutions, the slight discrepancies in these values can be attributed to simplifying the complex geometry and ignoring attributes like fillets and curvatures in the calculations.

Below the forceps feature, the bottle opener is appropriate for metallic caps, usually placed over cold drinks and

Fig. 5 Displacement of the free tip of the narrow strut under forceps action, a ABS, b PLA beverage bottles. On close inspection, it can be seen that the bottle opener arm, during the action, acts as a cantilever beam, subjected to a moment at the free end. The COVID key marks a two-point contact with the bottle cap, one with the bottle opener feature itself and the other with the struts to use the inbuilt bottle opener. To operate, the COVID key is fixed under the cap, pushed upwards from the wrench area and undergoes a pure rotation along with the point of contact with the struts, as shown in Fig. 6a . It is found that a moment of 12 lbs-in (1.356 Nm) is enough to open the cap of a bottle of beer (Jean-Philippe and Clerc 2002). Therefore, the pulling force, F, acting at a perpendicular distance, r ~ 25 mm, required for this action, is 55 N 1.356 0.025 only. The thinnest section in this feature is 10 mm wide and 5 mm thick. The corresponding bending stress has a peak value of 26.032 MPa in this section. Another element that undergoes pure bending is the thin flexural arm that can be primarily used for holding cylindrical/spherical entities such as doorknobs. A transverse force (F) is applied that elastically deforms the flexural arm to encapsulate the cylindrical/spherical entity for actions such as doorknobs and tap handles, as shown in Fig. 7 .

The flexural arm is oriented in a non-prismatic manner, w.r.t. the direction of the force. The cross-sectional area (and the area moment of inertia), measured along the plane parallel to the force, changes along the axial length of the arm. The deflection (y) of the arm (considered to be a cantilever beam) as a function of linear distance from the free end (x) is calculated by solving the second-order homogeneous differential equation, as follows:

where I x is the area moment of inertia at a given distance, (x), from the free end of the arm. The depth of section (b) is constant (10 mm) while the width (d) linearly varies from a maximum, d 1 = 3.22 mm, at the fixed end to the minimum d 2 = 2 mm. Therefore, the area moment of inertia at a given section can be calculated using Eq. 6.

Equation (5) then simplifies to Eq. (7).

L . Solving Eq. (7) yields the solution for free-tip deflection given by Eq. (8) as follows:

Substituting the value of A in Eq. (8) and solving for F yields Eq. (9).

The negative sign in the expression mentioned in Eq. (9) denotes that by limiting the maximum deflection,y max to 3 mm (10% of the maximum knob diameter permissible in this design, i.e. 30 mm), the force requirement comes out to be 36 N for ABS and 16.7 N for PLA. The maximum bending stress b(max) generated at the fixed end can then be calculated using Eq. (10):

FEA simulation is done for the validation of bending analysis of the thin flexural arm. The top face of the COVID key is chosen as a fixture, and a lateral force of 36 N for ABS and 16.7 N for PLA is applied in the negative (y) direction (refer to Fig. 7 for the coordinate system) the free end of the arm. A maximum deflection of 2.869 mm and maximum bending stress of 47.33 MPa are detected for ABS at the free-end and fixed-end. For PLA, 2.681 mm and 21.86 MPa is observed. Figure 8 shows the graphical representation of the same. The measured and calculated values of stress are under the yield strength of the respective materials. Hence, the design is safe and is under the elastic recoil limit for both materials.

The last element/feature to show bending based deflection is the pull feature used for applications like a door opener. Like the doorknob feature, the suitable door handle is placed behind the bottle-opener arm, from where it is pulled, by holding the key using the wrench feature hole. The pulling force is acted upon the rear side, approximately midway of the bottle-opener arm. This eccentricity of force generates a bending moment along the length of the COVID key. The thinnest cross-section is in the middle of the doorknob feature with a thickness of 8 mm. The section experiences a combined loading of axial force and bending stress. The maximum stress (max) is given as follows: where F is the pulling force (100 N), A is the minimum cross-sectional area (6 mm × 10 mm), M is the generated bending moment along the neutral axis of the section, y is the distance of the farthest fibre from the neutral axis (4 mm), and I is the area moment of inertia in the plane of cross-section 10.8 3 12 mm 4 . The distance of the point of application of force from the neutral axis is 21 mm, thereby generating a moment of 2.1 Nm. The maximum stress, calculated using Eq. (11), comes out to be 20.9375 MPa, which is within the elastic limit of the materials.

The deflection of the free end (i.e. strut region) can be calculated by assuming the COVID key as a cantilever beam subjected to a bending moment in between its length. Figure 9 depicts the mechanics modelling along with the where c 1 and c 2 are the distances of the point of application of moment from free-end and fix-end, respectively. For c 1 = 35 mm and c 2 = 65 mm, the maximum deflection came out to be 6.042 mm.

With a similar environment of fixture geometry and loading conditions, FEA analysis is done. Peak stress of approximately 19.58 MPa is observed in the vicinity of the minimal cross-sectional area. The deflection of the free-end tip came out to be 6.608 mm for ABS and 14.262 mm for PLA. Both these values are in close relationship with the analytical solution. Figure 10 shows the computational results of stress and displacement distribution of the "pull/ door-opener" feature of the COVID key.

Few elements also underwent torsional loadings, such as the hexagonal wrench feature and the sharp edge tool for screwbased applications. The torsional element under analysis is assumed to be homogenous throughout. The COVID key is assumed to be a circular shaft with a centrally aligned hexagonal cavity for wrench-based applications. The force is not directly applied over the wrench area. However, the generated torque is considered for the analysis, which is assumed to be constant throughout the length of that section.

In the case of the sharp edge, the section does not present a uniform cross-section along the direction of loading. An asymptotic limiting torque approach is used in that case to

calculate the angular deformation and displacement fields. It is assumed that the area profile remains the same before and after torque application at any given cross-section. Only the relative orientation between the sections changed, i.e. radial lines remain radial during torsion (Grassia et al. 2011 ). For wrench operations, within the range of 20 mm, the hexagonal cut-out feature is given in the COVID key. The design is analysed for a maximum force of 100 N applied at the farthest section from the wrench area, i.e. the strut region. The linear separation between the point of application of force at the rotational centre of the wrench came out to be 110 mm, generating a torque (T) of 11 Nm. The maximum shear stress is developed at the outermost section of the wrench area, which is at a radial distance of R = 15 mm. The generated shear stress ( ) at the periphery of the wrench area is calculated using Eq. (13) as follows:

where ( ) came out to be 2.891 MPa. The polar moment of inertia (J) of the circular section, of outer diameter (d = 30 mm) with a centrally aligned hexagonal cavity, of side length (a = 12 mm) is given by Eq. (14) .

The last design feature of the COVID key is the sharp edge, which can be used for screw actions under the impact of torque. The sharp edge is a triangular prism section, 2 mm wide (D), 2 mm long (H) and 8 mm thick (B), present at the end of the COVID key. For screwing action, the torque can be conveniently applied over the wrench area, with radially opposite sides in contact with the user's finger. The torque rating for a maximum applied force of 100 N at the wrench Fig. 9 Analysis of the "door-opener" feature area is 3 Nm (2 × 100 N × 15 mm). The cross-section of the sharp edge varies linearly from (2 mm × 8 mm) at the fixed end to theoretically a line element, 8 mm long at the free end, as shown in Fig. 11 . As the section presents a non-uniform cross-section, the conventional approach for torsional analysis and deflection cannot be used. An asymptotically limiting torque approach is applied to solve the problem, where the section under torque is divided into two units, one of which is infinitesimally narrow (x→ 0 ). These units have two different corresponding torque, adding up to the total applied torque. The ratio of the unit's torque is considered to be in proportion to the mass of individual units, which narrows down to the lateral areas of the unit. Mathematically,

The torque in the broad region ( T 1 ) deforms the material along the twist direction ( ) which is set by the narrow region torque ( T 2 ). Solving Eq. (15) for the narrow region torque yields T 2 ≃ 2.T.x D which when combined with the torsional properties provides the maximum linear deformation ( ) as follows:

where G is the shear modulus of the material. The maximum linear deflection came out to be 0.88 mm for ABS and 0.257 mm for PLA at the free end tip. The shear stress at the fixed end, near the root, calculated using Eq. (13), came out to be 66.17 MPa.

FEA simulation of the sharp edge feature is done under the similar loading conditions mentioned above. A maximum deflection at the free end and peak stress at the root section of 0.55 mm and 65.13 MPa for ABS; and 0.39 mm and 66.75 MPa for PLA is observed, respectively. The stress and displacement distributions for both materials are shown in Fig. 12 .

A topological optimization simulation analysis is also done on the COVID key design to get the optimal output subjected to specific constraints. The design is loaded with the previous mentioned forces and torques, subjected to appropriate fixtures. The optimization is set to a displacement constraint of the peak value of 15 mm at any given section. A goal of 10% mass reduction is also set. The peak stress is set to 65 MPa, as the Von-Mises limit of tensile and shear yielding. The set value is the minimum of both the materials, thereby innately saving both the materials. A 25% factory of safety (FoS) is used for calculating the peak stress using Eq. (17),

Manufacturing controls are also added to preserve selected regions of scale marking, keyholes and features like a bottle opener. To limit the simulation, thickness control is set if a section is going beyond the minimum limit of 2.15 mm. A die-mould control and a symmetry control are also added to set the demoulding direction (as used in injection moulding) and a half symmetry plane.

The results obtained from the optimization are shown in Fig. 13 . As the major section of the design is depicted in yellow (must keep section), the generated design is the optimized design.

The designed COVID key has many intricate features such as overhangs, fillets, slender parts, and holes. Therefore, an additively manufactured route using 3D printing is considered the best direction for its manufacturing. The presented design is 3D printed using ABS and PLA materials on an FDM 3D printer. Three different orientations of the part are possible relative to the built platform. In each orientation, there is the presence of overhanging structures, which requires support generation. The horizontal orientation with minimum support generation is chosen for 3D printing. Different orientation along with their support volume usage is shown in Table 2 . The part is oriented horizontally and deposited layer-by-layer with layer height set to 0.254 mm for optimized strength, surface finish and fabrication time (Mazzanti et al. 2019) .

Open source software, Ultimaker Cura ©, is used for slicing and gcode preparation. The commercially available FDM 3D printer, Creality Ender 3 ©, is used for prototyping. The print conditions are mentioned in Table 3 .

The 3D printed parts, along with the various real-life applications of the COVID key, are shown in Fig. 14.

A group of ten unbiased individuals is selected for the user satisfaction study. The qualified 3D printed COVID keys as per the proposed design are distributed to all ten individuals. The individuals are first given the usage's demo and then asked to use the key for their everyday activities mentioned in sections 1 and 2 for 15 days. On the 16th day, they are asked to evaluate their experience on the 10-point rating scale against six evaluation metrics, viz. ease of use, size, strength, appearance, material and ease of carrying. The results are mentioned in Table 4 and Fig. 15 . 

The present design of the COVID key has several features that incorporate intricate geometrical features and shapes. Additive Manufacturing (AM) using FDM 3D printing enables the production of the present COVID key with all its features without the need of special tooling. However, it is important to determine the production cost of the COVID key by the AM process.

The cost has components as fixed and variable costs. The fixed costs are independent of the increase or decrease of the production volume whereas variable costs vary in proportion with the production volume. For AM applications, there is a linearity in the variable costs as well, thereby providing a constant cost per part (Costabile et al. 2017) . The present article incorporates the FDM technique for the production of the COVID key. In the systematic calculation of the production costs for FDM systems there are several components such as pre-processing cost, material filament cost, machine depreciation cost, energy cost, consumables cost, post-processing cost and maintenance cost (Mello et al. 2010 ). There are several cost calculation approaches for AM depending on the production volume and the production strategy (Rosienkiewicz et al. 2018) . AM technology enables to produce different parts simultaneously using the single build platform. However, in this analysis, multiple instances of the same geometry are printed on the build platform for productivity considerations. The same approach is used by Hopkinson and Dickens (Hopkinson and Dicknes 2003) that factors in the machine cost per part, labour cost per part and material cost per part to give the total cost per part (CPP) (Eq. 18).

(18) C total = C machine + C labour + C material Three components are mainly machine cost per part ( C machine ), labour cost per part ( C labour ) and material cost per part ( C material ) that are added together to estimate the total cost per part ( C total ). The individual components are calculated by Eqs. (19) , (20) and (21).

The machine cost per component (C machine ) depends on machine equipment purchase cost ( E ), maintenance cost per year ( M ), number of components per build ( N ), time of machine operation per year in hours ( H ) and the time taken or completing one build ( T ). Here, the depreciation period of the machine is considered as 8 years (Rosienkiewicz et al. 2018) . Hence, the machine price is divided by 8. For calculation of the specific prices, the minimum price range for each of the particular item is considered, as per Indian AM markets. The pricing with various 3D printing service bureaus and the widely used machines in the service bureaus are also discussed during the study. The machine under consideration for the cost analysis is the one that has been used, i.e. Creality Ender 3. It is

widely used in the small sized 3D printing service bureaus and costs around (E) Rs. 15,000/-(~ 200 $/-). The average maintenance cost per year (M) is taken as Rs. 2,000/year (~ 27 $/year), which is approximately 13% of the equipment cost. The generic filaments of size 1.75 mm are considered with an average price of Rs. 1000/kg (~ 13.5 $/kg) for both ABS and PLA materials, after market research. With a bed area of 220 mm × 220 mm, a maximum of 7 COVID keys per built (N) can be easily printed without difficulty, as shown in Fig. 16 . The associated print time (T) is estimated to be roughly 16 h. Thereby, only one print, with full built platform, can be done in a single day. Considering that the machine runs for 300 days per year, the total working hours of machine operation per year (H) came out to be 4800 h/year. Hence, the machine cost per part ( C machine ), using Eq. (19), came out to be the following:

FDM 3D printers are totally automated machines, where the same set of commands (gcodes) can be used multiple times. A worker in a fabrication unit can start the FDM 3D printer in the morning. The set-up time for the machine (S) is mainly affected by the heating time of the extruder, which is usually in the range of 3-4 min, depending upon the material and environmental conditions. After printing, the post-processing involves removal of support material. The parts are fabricated in the orientation with minimum support usage. Hence, in about 5-10 s per part (P), the support material can be removed. In order to set an upper limit to the cost, the sum of setting-up and post-processing time (S + P) is taken as 4 min and 10 s, i.e. 250 s or 0.0694 h. An hourly wage of Rs. 30/hr (Rs. 240 per day for an 8-h work day) is taken as the minimum wage (W) in India for non-agricultural workers, involved in 3D printing industries (Litman et al. 2015) . The labour cost per part ( C labour ), calculated using Eq. (20), came out to be the following:

Creality Ender 3 is a single-extruder FDM 3D printer, where the same material (ABS or PLA) is used for both model and support, i.e. C support = C model , for a given material. Therefore, the total volume consumption, including model and support, per part is 20 cm 3 , which is equivalent The overall cost per part is the summation of the cost components calculated in Eqs. (22), (23) and (24). A tabular description of the same is given Table 5 .

From the table above, it can be seen that it is more economical (~ 26.6%) to go with ABS material for COVID key production.

A breakeven analysis is also done to determine the breakeven point and time to breakeven. Breakeven point is the minimum number of units (U) (in this case COVID keys) that needs to be sold to cover the costs. In order to generate a profit, a minimum of breakeven units has to be sold, as breakeven is the point of zero-profit. The time, in terms of (24) economic/working days needed to achieve breakeven point is the time to breakeven. A total cost function (TCF) is defined which is the sum of the fixed cost and variable cost. The fixed cost is taken as the equipment cost (E) and the overhead cost (O). The variable cost is defined as the cost per part fabricated. As ABS is more economical than PLA, Rs. 22.54/part is taken as the variable cost. With an overhead (O) of 40%, the total cost function is given in Eq. (25).

A through market research brought the price in the range of Rs. 70-150. We have considered a competitive price of Rs. 60 with approximately 167% profit margin (P*). Hence, a revenue function (RF) is set as Eq. (26).

To determine the breakeven point, the revenue generated should be surpass the total expenditure. Mathematically, Eq. (27) has to be satisfied for breakeven.

Solving the above equation for number of units (U), the breakeven point came out to be 561 units, i.e. after 561 st unit profit will be generated and the fixed cost will be covered.

Graphically, the point of intersection between RF and TCF, on the x-axis, gives the breakeven point, as shown in Fig. 17 . With an average production of 7 parts per day, it will take 80 days to reach breakeven. Multiple 3D printers can be simultaneously loaded to reduce the delay in breakeven.

Different case studies highlighting the multifunctionality of the presented design of the COVID key are reflected in this work. The detailed FEA analysis shows that the present COVID key is fit to be used in domestic and workplace settings. The prime application for the given COVID key is in the hospital buildings with a high number of people living or being treated for COVID. All majority actions such as pushing, pulling, pinching, tightening, measuring and holding can be performed satisfactorily with the present COVID key. Additively manufactured key from ABS plastic has the necessary strength and aesthetics to be operated as per the directions and is more economical from PLA, from manufacturing point of view. Extensive use of the key found that the actions can be performed swiftly with some practice. A user satisfaction study based on the six essential metrics found that users rate the most for the strength of the given key with a maximum of 8.9 ratings. The ratings for appearance, size, ease of use and ease of carrying are 8.8, 8.3, 7.7 and 7.2 respectively. The overall satisfaction rating is 8.18, and the preferred material is ABS.

• A novel key design that gives good protection against infectious surfaces by enabling a remote touch. • Multifunctionality of the key enables the user to perform various actions and reduces the need to carry multiple tools to perform a wide range of actions. • The size of the key is compact; hence it can be stored in the pockets, handbags and purse after proper sanitization. • The geometry is simplified to make it suitable for 3D

printing where the CAD model can be shared with people. It can be printed from the nearby 3D printing facility. It makes the distribution of the key easy and widespread.

• It could be troublesome to use the key initially due to a lack of experience in using it. Thus, the authors suggest using the key repeatedly to get accustomed to social settings. • Key is not suitable for some very specific or extreme applications with size and temperature constraints. However, the design and material can be modified to suit the particular application.

Optimization of fused deposition modeling parameters for improved PLA and ABS 3D Printed Structures

Consistency analysis of mechanical properties of elements produced by FDM additive manufacturing technology

Likelihood of survival of coronavirus in a respiratory droplet deposited on a solid surface

Turbulent gas clouds and respiratory pathogen emissions: potential implications for reducing transmission of COVID-19

Experimental characterization of the mechanical properties of 3D-printed ABS and polycarbonate parts

Cost models of additive manufacturing: a literature review

Experimental characterization and micrography of 3D printed PLA and PLA reinforced with short carbon fibers

Modeling of density evolution of PLA under ultra-high pressure/temperature histories

Analysis of rapid manufacturingusing layer manufacturing processes for production

Autonomous Bottle Opener Robot

The relationship between motivation, monetary compensation, and data quality among USand India-based workers on Mechanical Turk

FDM 3D printing of polymers containing natural fillers: a review of their mechanical properties

Systematic proposal to calculate price of prototypes manufactured through rapid prototyping an FDM 3D printer in a University Lab

Grip force and pinch grip in an adult population: reference values and factors associated with grip force

Additive manufacturing technologies cost calculation as a crucial factor in industry 4.0. Lecture notes in mechanical engineering

Measurements of the mechanical response of unidirectional 3D-printed PLA

Theory of Elastic Stability

Mechanical property optimization of FDM PLA in shear with multiple objectives

Mechanical properties of acrylonitrile butadiene styrene thermoplastic polymer matrix with carbon nanotubes

A novel Coronavirus outbreak of global health concern

WHO (2020) Modes of transmission of virus causing COVID-19: implications for IPC precaution recommendations

The effects of PLA colour on material properties of 3-d printed components