key: cord-0865408-anitpnav
authors: Gong, Fanwu; Wei, Hua-xing; Qi, Ji; Ma, Huan; Liu, Lianxin; Weng, Jianping; Zheng, Xucai; Li, Qiangsheng; Zhao, Dan; Fang, Haopeng; Liu, Liu; He, Hongliang; Ma, Cuichen; Han, Jinglong; Sun, Anyuan; Wang, Baolong; Jin, Tengchuan; Li, Bowei; Li, Bofeng
title: Pulling-Force Spinning Top for Serum Separation Combined with Paper-Based Microfluidic Devices in COVID-19 ELISA Diagnosis
date: 2021-07-15
journal: ACS Sens
DOI: 10.1021/acssensors.1c00773
sha: 01100adba4e7a16601986c20cade24738fe27215
doc_id: 865408
cord_uid: anitpnav

[Image: see text] The spread of Coronavirus disease 2019 (COVID-19) is caused by severe acute respiratory syndrome-coronavirus 2 (SARS-CoV-2), resulting in a global pandemic with around four million deaths. Although there are a variety of nucleic acid-based tests for detecting SARS-CoV-2, these methods have a relatively high cost and require expensive supporting equipment. To overcome these limitations and improve the efficiency of SARS-CoV-2 diagnosis, we developed a microfluidic platform that collected serum by a pulling-force spinning top and paper-based microfluidic enzyme-linked immunosorbent assay (ELISA) for quantitative IgA/IgM/IgG measurements in an instrument-free way. We further validated the paper-based microfluidic ELISA analysis of SARS-CoV-2 receptor-binding domain (RBD)-specific IgA/IgM/IgG antibodies from human blood samples as a good measurement with higher sensitivity compared with traditional IgM/IgG detection (99.7% vs 95.6%) for early illness onset patients. In conclusion, we provide an alternative solution for the diagnosis of SARS-CoV-2 in a portable manner by this smart integration of pulling-force spinning top and paper-based microfluidic immunoassay.

C oronavirus infection leads to a public health crisis since the beginning of the 21st century, 1 including the appearance of severe acute respiratory syndrome-coronavirus (SARS-CoV) in 2003 and Middle East respiratory syndrome-coronavirus (MERS-CoV) in 2012, especially the new emergency of coronavirus disease 2019 (COVID- 19) , which has spread rapidly all over the world. 2, 3 After infected with SARS-CoV-2, patients have respiratory symptoms, such as cough, fever, and shortness of breath. Moreover, patients with severe disease could develop pneumonia, kidney failure, and brain failure or even die. 4 The current global coronavirus epidemic is progressing quickly, causing a huge health and economic problem. To date, the total number of infected people has exceeded 173 000 000, as well as more than 3 700 000 deaths.

Therefore, there is an urgent need for a more reliable and cheap diagnostic method to screen and distinguish the SARS-CoV-2-infected patients from healthy people. To date, most clinical inspections of the SARS-CoV-2 virus are based on the real-time polymerase chain reaction (PCR) analysis of nasopharyngeal or throat swab samples or enzyme-linked immunosorbent assay (ELISA) about detecting the expression of virus protein. There is always a concern about the difficulty of obtaining high-quality throat swab samples, and comparative lower viral load at the early stage of infection, resulting in a high false-negative rate. 5, 6 On the other hand, lateral flow rapid test strip gives a way to confirm the presence or absence of the SARS-CoV-2 virus, but it cannot provide quantitative information and lead to a limitation in clinical practice.

Many people in developed countries have been infected with SARS-CoV-2, such as the United States, United Kingdom, Italy, etc. In addition, more than 100 other countries and regions around the world have also found COVID-19 patients, including many third-world countries. 7, 8 These third-world countries have large populations, high population density, and insufficient medical resources. Although there are a variety of reverse transcription polymerase chain reaction (RT-PCR) kits for detecting SARS-CoV-2, the RT-PCR method has a relatively high cost and requires expensive supporting equipment. It is crucial to develop some new methods to achieve low-cost and fast detection of SARS-CoV-2. 5 Recently, microfluidic paper-based analytical devices (μPADs) have been a hotspot of research due to their multiple inherent advantages, such as low cost, small reagent consumption, no external power source, and good biocompatibility. 9−11 Therefore, microfluidic paper chips are increasingly being used in many fields including point-of-care testing (POCT), 9, 12 environmental monitor, 13, 14 clinical analysis, 9, 15 food processing, and chemical industries. 16 For example, Yu's group used three-dimensional paper-based electrochemiluminescence and chemiluminescence immunoassays to develop a series of methods for the measurement and rapid testing of biomarkers. 17−19 Bhamla and his co-workers invented a paper centrifugation technology that worked without electricity and separated blood in a few minutes. 20 Using a high-speed centrifugal rotation of the fidget spinner, Michael made a rapid diagnosis of urinary tract infection 21 and Liu realized the human immunodeficiency virus (HIV-1) detection. 22 We also provided integrated hand-powered centrifugation-combined ELISA diagnosis on a microfluidic device. 9 As is well known, mature SARS-CoV-2 contains four conserved structural proteins: spike (S), envelope (E), membrane (M), and nucleocapsid protein (N), as well as several accessory proteins. 7, 23 More importantly, S protein contains S1 and S2 subunits, while receptor-binding domain (RBD) as part of S1 submit can bind to human angiotensinconverting enzyme 2 (ACE2) receptor, thus playing an essential role for the entrance into the cell membrane. 24, 25 When the virus invades the host, the immune system produces large amounts of immunoglobulins (IgG, IgM, and IgA), which were released into the blood. 26, 27 Now, detecting RBD-specific antibody productions is a novel serological method and has unique advantages in clinical diagnostics, especially for identifying people who have acquired immunity against pathogens without noticeable symptoms. 5 It has been widely believed that IgM is the first antibody to be transiently synthesized in response to the virus invasion. 28 IgG is a major class of immunoglobulins found in the blood, which is induced by a secondary immune response and has long-term immunity and immunological memory. 29, 30 Therefore, a traditional IgM/IgG combination was used to diagnose the SARS-CoV-2 infection initially; however, the effect was questionable. Our previous study found that IgA also appeared at the early stage of the disease, 31 starting to be used as a good marker in the detection of SARS-CoV-2. 32, 33 We had successfully built a serological solution to monitor the infection of SARS-CoV-2 virus by detecting the serum RBDspecific IgA/IgM/IgG productions and proved that the combination of these parameters greatly increased the sensitivity of the diagnosis. 31 However, this method still requires the apparatus (automatic chemical luminescent immuno-analyzer, Kaeser 1000), which is expensive for the health services of thirdworld countries. To further overcome these limitations, we present a new way using pulling-force spinning top (PFST) combined with paper-based microfluidic technique to accomplish blood−serum separation and diagnose the SARS-CoV-2 by analyzing the RBD-based IgA/IgM/IgG indicators. This measurement has three great advantages: (1) we proved great specificity and sensitivity of the combined anti-RBD IgA/IgM/ IgG detection, giving a >99% accuracy of confirming the SARS-CoV-2 infection, and it will be a useful candidate method for clinical RT-PCR diagnosis; (2) people can isolate the serum without any clinical apparatus, and a portable smart phone is easy to record the intensity signal; (3) the manufacturing cost of a single PFST-μPADs device is no more than $5. These merits provide an economic and reliable solution for both undeveloped and developed countries. We expect this new technology will bring convenience for diagnosis of SARS-CoV-2 and eliminate the dependence on medical apparatus, making the community clinics, family care clinics, and even home diagnosis of SARS-CoV-2 feasible.

Materials. For serum collection, disposable capillaries (YZB, 0002-2009) were purchased from Yongming Medical Technology, Inc. (Yantai, China); disposable blood needles (Cat# 01-0628D) were purchased from STERILANCE (Suzhou, China); the spinning top was bought from "children star" toy store at Pinduoduo internet store (PDD.US); and reheating melt rubber gun (model# RJQHAC50-GC113) was purchased from GANCHUN (Shanghai, China). Chitosan (SCR, Cat# 17779) and glutaraldehyde (SCR, Cat# 30092436) were purchased from Chemical Reagent Repertory, University of Science and Technology of China. RBD, anti-RBD-IgA, anti-RBD-IgM, and anti-RBD-IgG antibodies were purified in our lab. 31 HRP-conjugated goat-anti-human IgA (Cat# BA1066) and HRPconjugated goat-anti-human IgM (Cat# BA1077) were purchased from Boster Biological Technology Co. (Wuhan, China); goat-anti-human IgG (Lot# SSA015) was purchased from Sino Biological, Inc. (Beijing, China); HRP-conjugated rabbit anti-goat IgG (Lot# D110117) was purchased from Sangon Biotech (Shanghai, China), which was also called anti-anti-IgG; and TMB solution (Cat# P0209) was purchased from Beyotime Biotechnology (Shanghai, China).

Design and Fabrication of μPADs. The paper-based device was designed by the illustrator software and fabricated by a wax printing process. The detailed process has been described in the literature. 34, 35 Briefly, the designed patterns were printed on Whatman No. 1 filter paper via a XEROX Phaser 8560DN wax printer. Then, patterned papers were kept in an oven at 150°C for 30 s to make the wax penetrate the printer completely. To carry out the complex multistep operations, we used plastic comb binding spines (PCBS) valves to control fluid's transportation and perform ELISA assay including antibody immobilization, sample dispensing, and washing.

Paper-Based Chip ELISA Test. Human serums were obtained from three groups of people: SARS-CoV-2-infected group at an early stage (4−10 days), late stage (14−27 days), and healthy control group. Human serum antibodies (anti-RBD-IgA, anti-RBD-IgM, and anti-RBD-IgG) were detected. First, 5 μL of 0.25 mg/mL of chitosan was added to every hydrophilic immuno-zone (circle shape) and dried at room temperature. Then, 5 μL of 2.5% of glutaraldehyde dissolved in phosphate-buffered saline (PBS) (pH = 7.4) was added to each immuno-zone. After 2 h of reaction, immuno-zones were washed with 10 μL of ddH 2 O three times. Next, 5 μL of RBD (diluted to 2 μg/mL) was added to immuno-zones at room temperature. After 30 min, immuno-zones were washed with 10 μL of PBS three times through PCBS valves. Then, 5 μL of 0.5% bovine serum albumin (BSA) dissolved in PBS (pH = 7.4) was added to immuno-zones at room temperature to block the nonspecific binding sites. Immuno-zones were washed three times with PBS 20 min later. After that, 5 μL of anti-RBD antibody standards and human serums were added to immuno-zones at room temperature. Anti-RBD antibodies (IgA/IgM/IgG) were doublediluted from 100 to 0 ng/mL as standards (100, 50, 25, 12.5, 6.25, 0 ng/ mL). Human serums were diluted 1:100 (healthy people and infected patients) with PBS before adding into the immuno-zones. After 30 min, immuno-zones were washed three times with PBS. Next, 5 μL of second antibodies specific binding to anti-RBD IgA (500 ng/mL), anti-RBD IgM (500 ng/mL), or anti-RBD IgG (500 ng/mL) was added to immuno-zones at room temperature in the dark. After 30 min, the immuno-zones were washed three times with PBS. As second antibodies of IgA and IgM were labeled with HRP, while IgG second antibody did not, 5 μL of HRP-labeled IgG third antibody (500 ng/ mL) was added to immuno-zones at 4°C in the dark and washed after 30 min. After the second and third antibodies were washed, 20 μL of TMB solution (3,3′,5,5′-tetramethylbenzidine, substrate of HRP, double-diluted with PBS) was added to each sample and reacted with HRP at room temperature in the dark. After 2 min of chromogenic reaction, the paper-based chips were photographed by a smart phone.

pubs.acs.org/acssensors Article Any type of smart phone with a good camera is usable. Finally, the pictures were analyzed by ImageJ software, the gray values of immunozones were obtained, and the concentrations of RBD antibodies of the immuno-zones were calculated. Production of RBD and RBD-Based IgA/IgM/IgG Standards. RBD and anti-RBD antibodies (IgA/IgM/IgG) were purified as described previously. 36 Briefly, to make the recombinant SARS-CoV-2 RBD, a leader sequence, a sequence encoding spike protein RBD, and a human IgG1-Fc were fused together. This sequence was cloned into pTT5 vector and then transiently transfected into HEK293F cells through polyethylenimine. After 3 days, RBD was purified from cell supernatant using protein A column (GE Healthcare). For purification of RBD-based IgA/IgM/IgG, the antigen-immobilized affinity columns were used. The purified RBD was coupled to agarose resin (CNBractivated Sepahrose 4B) according to the manufacturer's protocols (GE Healthcare), packed into an empty column. Next, the antibody standards were purified from patients' serums. Briefly, ammonium sulfate powder was added to the serums and dissolved. After centrifugation, resuspension, and filtration, the patient's serum samples were loaded onto an RBD-Fc affinity column and eluted by linear gradient of elution buffer. The RBD-specific IgG, IgM, and IgA were then purified using a protein G column and further verified by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) and mass spectrum.

Statistics. Statistics were calculated using Prism5 (GraphPad Software). Group comparisons were analyzed by a two-sided Student's t-test. A p < 0.05 was considered significant. Numbers of asterisks mean significant difference (*p < 0.05; **p < 0.01; ***p < 0.001; ****p < 0.0001).

New Platform for SARS-CoV-2 Diagnosis and μPADs Fabrication and Assembly. To diagnose SARS-CoV-2 infection in an efficient and economical way, we designed a new platform as shown in Figure 1 . This platform contains a pulling-force spinning top and a μPAD ( Figure S1 ). Because ELISA is a very popular and reliable assay for SARS-CoV-2 detection, our platform used a combination of virus RBDspecific IgA/IgM/IgG antibodies to increase the specificity and sensitivity.

We constructed a paper-based device based on PCBS valves with six parallel channels to perform the ELISA reaction for the detection of SARS-CoV-2. As shown in Figure 1B −E, the chip contains two layers and discontinuous channels. The top layer comprises two long-arm papers, and each component contains six channels. Like flipping calendar, through moving long-arm component, the function of connection (ON state) or disconnection (OFF state) could be achieved using this PCBS. Briefly, when the valves are at an ON state, the longarm paper can connect the middle circles (second layers), which are the immuno-zones, and the liquid could flow from H, I, J, K, L, M reservoirs to the H′, I′, J′, K′, L′, M′ reservoirs, respectively. In this situation, the residue in the immuno-zones could be washed easily by capillary force (Video S1). Also, at the OFF state, the immuno-zones disconnect from the long-arm paper ( Figure 1B −E). Because ELISA reactions generally have multiple processes, such as incubating different immunoreagents, nonspecific-site blocking, multiple washing, etc., the PCBS valves are very convenient for fast diagnosis of SARS-CoV-2 at the place without medical equipment.

Isolating the Serum from Blood by the PFST Method. As the spinning top could rotate fast, we considered whether it could be used to separate the human whole blood. The detailed pictures of the spinning top are shown in Figure S2 . Whole blood samples from healthy people were exposed from fingers by disposable blood needles and siphoned into capillaries. The blood capillary tube has an outer diameter of 1.4 mm, an inner diameter of 0.6 mm, as well as 50 mm length. Blood was loaded into every capillary, enough for all subsequent analyses on the μPADs. One end of capillaries was sealed up by melting glue. Then, capillaries were immediately fixed on the surface of spinning top by melting glue, and the sealed end was against the center of spinning top while the unsealed end was close to the center. About 20 μL of whole blood in each capillary tube was separated by PFST. As expected, the volume of serum obtained increased with the accumulated centrifugation time and the amount of serum reached the plateau after 4−5 min (Video S2). The serum was taken out by a Hamilton syringe on the upper layer of capillaries. The average amount of serum collected from each centrifuge tube was about 8 μL, and this quantity is enough for the following ELISA assays (Figure 2A ). It is worth noting that we also addressed the impact of different persons on the isolation of serum in this system. Four different persons used the PFST method to collect the serum from human blood; it took around 4−5 min for the length of the serum to reach the plateau, indicating that the PFST method is suitable for adults ( Figure  2B ). Accordingly, for the following experiments, we selected a centrifugation time of 5 min.

We only calculate the maximum speed of the spinning top when it is pulled for the first time and pulled once. If it is pulled 

pubs.acs.org/acssensors Article continuously, the spinning top will reach a higher speed. As shown in Figure S3 , when the rope is pulled, the gear transmission is triggered, and the spinning top has begun to rotate. Therefore, the energy of the spinning top comes from pulling the rope. If the friction is ignored, the kinetic energy theory can be obtained

where W input is the total pulling energy, E S is the kinetic energy of rope, and A, B, C, and D represent the rope, gear A, gear B, gear C, and the spinning top, respectively ( Figure S3 ). Also, E S is the kinetic energy of rope; E A , E B , and E C are the kinetic energy of gear A, gear B, and gear C, respectively; and E D is the transmission kinetic energy of the spinning top. Therefore, we can obtain the following equation

where F max is the maximum pulling force of the rope under normal conditions, L s is the rope length, m s is the mass of the rope, v s is the instantaneous movement speed of the rope, I is the moment of inertia of the gear, and ω is the instantaneous angular velocity of the gear. If we regard the gear to be similar to a cylinder, its moment of inertia can be approximately calculated by the existing formula

According to the gear ratio formula

where n is the number of gear teeth. And after simplification, we can get the following formula 

Using a push−pull tester, the pulling force was around 10 N. 9 Using various data as shown in Table S1 , we get the maximum angular velocity of the first pulling Optimization of the Detection Conditions. As is well known, ELISA performance on the paper chips is also highly related to the parameters such as antigen/antibody incubation time, and pH value. Therefore, we investigated the different incubation times of primary antibody, HRP-labeled secondary antibody, and RBDs.

The incubation time for the primary antibody and the HRPlabeled secondary antibody (HRP-anti-IgA 500 ng/mL, and 

pubs.acs.org/acssensors Article anti-RBD IgA 100 ng/mL) was optimized. As displayed in Figure 2C ,D, we observed that the intensity of signal production of ELISA increased with longer incubation time, the intensity of anti-RBD IgA (the prime antibody of IgA) stabilized after an incubation time of 18 min, and the intensity of the HRP-labeled antibody for IgA stabilized after 21 min. To determine the optimal incubation time for the RBD antigen, we studied various incubation times ranging from 0 to 33 min. As shown in Figure  2E , the signals reached a plateau after an incubation time of 20 min. Therefore, we selected 20 min as a preferred condition. Due to the great influence of pH on the quality and intensity of signal production in ELISA assay, we next examined different conditions of wash buffer with pH value from 6.0 to 9.0. As shown in Figure 2F , the level of anti-RBD IgA peaked at pH 7.4, while under other pH conditions, the detected intensity signals were all lower than that. Based on this result, we chose pH 7.4 as the standard elution condition for all of the assays in this study. Similarly, under the best pH condition, incubation times for the primary and secondary antibodies of anti-RBD IgM and anti-RBD IgG were as same as that of anti-RBD IgA.

Analytical Performance of PFST-μPADs. To characterize the specificity and sensitivity of our μPADs, we performed our ELISA immunoassay using the RBD-based IgA/IgM/IgG combination detection system. Briefly, we used our purified recombinant RBD to capture SARS-CoV-2-specific IgA, IgM, and IgG antibodies in patients' serum. We collected these patient-derived IgA/IgM/IgG and prepared our standard for IgA, IgM, and IgG, which specifically recognize SARS-CoV-2. As our previous report, 31 we showed 98.2 and 100% specificity and sensitivity, respectively, in our fluorescence detection system, which could detect the luminescent intensity by an automatic immuno-analyzer. Due to the high cost of this apparatus, we planned to design a new technology with a handy device, with no cost of the luminance machine. To simplify this method, we used the HRP-catalyzed TMB−H 2 O 2 solution to detect the immune reaction signal, and the signal could be directly photographed by a smart phone. Then, the color could be exchanged to intensity by an open-source tool (ImageJ software). The analytical performance was assessed under optimal conditions through the application of RBD-based IgA/IgM/IgG. Standard solutions of anti-RBD IgA/IgM/IgG (0, 6.25, 12.50, 25.00, 50.00, 100.00 ng/mL) were directly introduced to immune-zones on the paper-based chips. As shown in Figure 3A −D, the signal (blue color) increased linearly with IgA, IgM, or IgG concentration between 0 and 100.00 ng/mL. A simple linear regression analysis yielded fits of y = 0.5339x + 4.251 (R 2 = 0.975) for anti-RBD IgA, y = 0.5141x + 0.192 (R 2 = 0.956) for anti-RBD IgM, and y = 0.6944x + 3.871 (R 2 = 0.966) for anti-RBD IgG, where y is the relative intensity and x represents the protein concentration.

To investigate the reliability of our μPADs, we performed a conventional ELISA assay to compare the expression of RBDbased IgA/IgM/IgG, the chemiluminescent intensities of which were detected by a spectrophotometer with the absorbing wavelength at 450/595 nm. As shown in Figure S4A −C, a very 

pubs.acs.org/acssensors Article similar pattern of the trend line (slope and R 2 ) of anti-RBD IgA, IgM, and IgG was observed from μPADs results. Based on these findings, we confirmed that the accuracy of our μPADs with collecting the digital intensities by smart phone was as good as the conventional ELISA assay detected by a BioTek SYNERGY H1 microplate reader.

Detecting the Late Stage of SARS-CoV-2-Infected Patient's Serums. To further evaluate the diagnostic accuracy of our PFST-μPADs detection method, we measured RBDbased IgA/IgM/IgG production from COVID-19-infected patients compared to healthy people. We collected 55 serum samples from the First Affiliated Hospital of University of Science and Technology of China, including 35 serum samples from healthy people and 20 serum samples from qPCRconfirmed SARS-CoV-2 patients with more than 14 days postsymptom onset (DPSO), considered as late stage of the disease 37 (Table S2) Then, denaturant solution (1% TNBP + 1% Triton X-100) was added to each tube at 30°C for 4 h to completely denature any potential viruses. And we obtained these deactivated serums of COVID-19 patients. On the other hand, we collected whole blood samples from 35 healthy people and isolated their serums using our PFST method in our lab.

To find the fitful conditions for the good range of serum samples from healthy people and infected patients, we tested the different dilution ratios of these serum samples and found that the intensity of fluorescence showed no decrease up to 1:20 dilution, and the signals of 1:100 dilution displayed 1/3 peak value ( Figure S5A,B) . We then choose 1:100 dilution in all of the experiments. All samples were then measured by our paperbased anti-RBD IgA, IgG, and IgM detection method. The results are shown in Figure 4A −C, with detailed numbers in Table S3 as well. These three antibodies bind to SARS-CoV-2 RBD viral antigen with high specificity, which is consistent with our previous report. 31 Based on the immunological principle, only anti-RBD IgA/IgM/IgG immunoglobin can recognize viral RBD, whereas other nonspecific IgA/IgM/IgG immunoglobin Detecting the Early Stage of SARS-CoV-2-Infected Patient's Serums. As we observed the presence of a high level of RBD-specific IgA in COVID-19 patients' serums. It is well known that during the virus infection, such as EV-71 38 and influenza, 39 a high level of pathogen-specific IgA has been produced. IgA is not only present in the serum of SARS 40 and COVID-19 patients, 30 but also produced by the immune system faster than IgG at the early stage of the disease, suggesting the importance of IgA in immune responses against viral infection. 32, 33 Next, we explored the sensitivity and specificity for these different antibodies at earlier time points to examine whether our IgA/IgM/IgG combined method is good enough for the diagnosis of COVID-19 patients at the early stage of disease development. We collected 49 serum samples from the First Affiliated Hospital of University of Science and Technology of China, including 34 serum samples from healthy people and 15 serum samples from qPCR-confirmed SARS-CoV-2 patients within 4−10 days post-symptom onset, considered as the early stage of the disease 36 (Table S4 ). As shown in Figure 5 , with detailed numbers in Table S5 , the corresponding sensitivities of IgA, IgM, and IgG were 93.3% (14/15), 86.7% (13/15), and 66.7% (10/15). The sensitivity of the IgA/IgM/IgG combination is much higher than the traditional IgM/IgG combination (99.7% vs 95.6%). On the other hand, both IgA and IgG showed 100% (34/34) specificity for detecting the SARS-CoV-2, while IgM only shows 91.2% (31/34) ( Figure 5) . Together, IgA test has less false positives, while IgG is not a good marker for people at the early stage of the disease. For IgM, it displays 86.7% sensitivity and 91.2% specificity, both lower than those of IgA.

To investigate the reliability of our μPADs, we performed a conventional ELISA assay to detect the levels of RBD-based IgA/IgM/IgG by a microplate reader with the absorbing wavelength at 450/595 nm. As shown in Figure S6A −C and Table S6 , the sensitivities of RBD-based IgA, IgM, and IgG for the late-infected cases were 100% (20/20), 95% (19/20) , and 100% (20/20), respectively, displaying an identical result compared to paper-based microfluidic ELISA. Meanwhile, the specificities for the three antibodies were all 100% (35/35). A very similar pattern of the early-infected group was displayed ( Figure S6D−F) . Based on these findings, we confirmed that the accuracy of our μPADs with collecting the digital intensity by a smart phone was as good as the conventional ELISA assay.

To draw a full picture of the effect of IgA/IgM/IgG combination, we calculated all patients' samples (both early and late infected) and healthy people's samples (Table 1 ). In the strictest way, we regarded serum samples as positive when any levels of IgA, IgM, or IgG over the detection threshold. In this rule, IgA and IgG still showed 100% specificity for healthy people, while IgM only shows 92.8% specificity. Because of the existence of IgM, the specificity of IgA/IgM/IgG combination detection is equal to that of IgM detection alone (92.8% vs 92.8%).

Interestingly, if we choose IgA/IgG combination, the specificity is 100%, meaning no false-positive case during the diagnosis ( Table 1) . As traditional IgM/IgG combination diagnosis is widely used in clinical practice, to avoid divergence and doubt, we still acknowledged the IgA/IgM/IgG combination instead of IgA/IgG combination in the serological test.

In the immune system, a large amount of various IgG exists in the body to respond to various antigens. Therefore, we performed a 96-well plate ELISA experiment to detect the concentration of total IgG in the blood of patients as well as healthy people and calculated the percentage of the anti-RBD IgG among total IgG ( Figure S7 and Table S7 ). As the result shows, the total IgG of the patients, especially early-infected patients, was very close to the total IgG of the healthy people ( Figure S7A,B) . This result can explain why detecting of serum total IgG always has limited accuracy. Furthermore, we found 0.156% of anti-RBD IgG/total IgG in late-infected COVID-19 patients, 0.023% of anti-RBD IgG/total IgG in early-infected patients, and no more than 0.007% of anti-RBD IgG/total IgG in healthy people ( Figure S7C ,D and Table S7 ). This experiment proved that our strategy greatly increased the detection sensitivity of SARS-CoV-2, compared to other clinical ELISA assays examining on total IgG. Moreover, the proposed method by pulling-force-assisted spinning top for blood−serum separation and analysis on microfluidic chip achieved good performance and showed good potential in home diagnosis.

In summary, we highly recommend anti-RBD IgA combined with anti-RBD IgG/IgM method to increase the diagnostic accuracy of SARS-CoV-2 on this microfluidic platform. It displays great diagnostic accuracy for SARS-CoV-2 (99.9% sensitivity and 92.8% specificity). Therefore, the use of RBDspecific IgA/IgM/IgG combinational serological test as another solution provides an accurate diagnosis of SARS-CoV-2 on this microfluidic platform. 

In this study, we designed a portable PFST-μPAD platform. This device not only shows great sensitivity and specificity for SARS-CoV-2 diagnosis but also provides a quantitative anti-RBD IgA/ IgM/IgG detection method in an instrument-free way. Recently, our IgA/IgM/IgM combination diagnosis method is recommended by the Canadian Society of Clinical Chemists (CSCC) interim consensus guidance. 41 More importantly, the novel microfluidic device that separates serum from whole blood and provides quantitative IgA/IgM/IgG combined measurements in a rapid, portable, and potential home diagnosis way. This platform has multiple inherent advantages, such as low costs, small reagent consumption, and no external medical machine needed. It is fit for several application scenarios: (1) undeveloped countries' medical centers, which do not have expensive apparatus; (2) diagnose at developed countries' community clinic to avoid the cross-infection in the crowded hospital; and (3) provide a potential home diagnosis possibility for people who have the experience to take their own blood. It is well known that IgA is greatly induced during the virus infection, such as EV-71 38 and influenza. 39 During the SARS-CoV-2 infection, we previously found IgA and IgM appeared at the early illness onset, while IgG usually emerged 14 days after the onset of symptoms. 31 We proved the combination of the RBD-based IgA/IgM/IgG giving better diagnosis results compared with the traditional IgM/IgG methods. These come from two immunological principles: one is RBD-specific IgA/ IgM/IgG can improve the accuracy due to its specific recognition of viral RBD, and the other is IgA can be detected both in early and late stages of the disease, while IgG cannot be detected. These data are consistent with another finding that the IgM and IgG combinatorial detection of SARS-CoV-2 displayed low accuracy for the early stage (1−7 days) and higher accuracy (96.8%) at the late stage (>15 days). 42 Although IgM appears as early as IgA, the sensitivity of IgM for early illness is not accurate compared to IgA diagnosis ( Figure 5 ). This may explain why traditional IgM/IgG diagnosis is not accepted by the clinical validation of the COVID-19 patients.

Among 20 PCR-confirmed positive patients at the late stage of the disease and 15 early onsets, we achieved 97.1% sensitivity and 100% specificity by anti-RBD IgA detection itself. Other studies also showed the good performance of IgA detection. 43, 44 Thus, we identified that IgA/IgM/IgG combination brought 99.7% sensitivity for patients at early illness onset compared with traditional IgM/IgG diagnosis, only displaying 95.6% sensitivity (Table 1) .

This study also has some limitations, a major limitation is a low number of patients, and especially we only collect 15 earlyonset patients' samples. Second, as is well known, COVID-19 is a virulent infectious disease, serum inactivation is necessary to prevent the potential risk of infection. We had to obey the requirement of the Medical Ethical Committee of the First Affiliated Hospital of University of Science and Technology of China (approval number: 2020-XG(H)-014 and 2020-p-060), otherwise this study would not be approved. Thus, we only separated the serum from healthy people by the PFST method, not for that from infected people. Finally, to get high-quality results at home by people themselves, it requires these persons to have a basic skill of operating ELISA assay. That is why, we considered our study not only designed a potential home diagnosis method but also provided a new solution for the community clinics, which did not have expensive equipment.

Also, the cost of this paper-based microfluidic ELISA assay is cheaper than conventional ELISA because only 5 μL of samples or reagents need to be loaded compared with 50 μL volume for conventional ELISA.

Since the appearance of SARS-CoV-2, some rapid detection diagnosis methods were developed, 35, 45 including Cas13-based technique, 46 DNA nanoscaffold-based assay, 47 lateral flow immunoassay, 48 chest CT scan combining a series of X-ray images, 49 and multiplexed nanomaterial-based sensor array, 50 but all of these methods neither require an expensive analyzer nor provide quantitative results. Our PFST-μPAD method provides a solution for people to isolate their samples and detect a bio-marker of SARS-CoV-2 in a very convenient and portable way without any clinical apparatus, which makes home diagnosis achievable and available. Moreover, our detection system shows high specificity and sensitivity to SARS-CoV-2 infection, indicating that the PFST-μPAD-based detection of anti-RBD IgA/IgM/IgG might be a fast, cheap, and facile way for SARS-CoV-2 diagnosis.

In summary, we reported a novel and handy way to isolate the serum from whole blood by the PFST method and detect the RBD-based IgA/IgM/IgG concentrations by μPADs. It provides an affordable, rapid, and user-friendly way to the diagnosis of COVID-19 in a microfluidic format. By the combination of the viral RBD-specific antibodies (anti-RBD IgA/IgM/IgG), our methods displayed great sensitive and quantitative serological results. It is worth noting that our PFST-μPADs system can also be used for the diagnosis of COVID-19 patients both at the early and late stages of the disease. Moreover, no need for the clinical apparatus and low cost of the portable device give a new solution for both developed and undeveloped countries to monitor the spread of the COVID-19 disease in a potential home diagnosis pattern.

The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acssensors.1c00773.

PFST-μPADs detection platform; photographs of the spinning top with its handle; picture of the gears A, B and C, spinning top, and the rope inside the handle; canonical ELISA standard curves for human RBD antibodies concentration on 96-well plate; option of dilution ratio of SARS-CoV-2 patients serums; serum antibody levels in SARS-CoV-2 patients and healthy people in conventional ELISA detection; serum total IgG concentration and the proportion of the anti-RBD IgG among total IgG in SARS-CoV-2 patients and healthy people; information of four gears and the pulling rope of the spinning top; information of the 20 late-stage COVID-19 patients 

pubs.acs.org/acssensors Article and anti-RBD IgG determination results; sensitivity and specificity of RBD-specific IgA, IgM, and IgG, as well as three different combinations for diagnosing in conventional ELISA detection; and the serum total IgG concentration determination results and the proportion of the anti-RBD IgG among total IgG in the early-and late-infected patients and healthy people (PDF) Entire fabrication process of PCBS valves (Video S1) (MP4) Serum collection by the PFST method (Video S2)(MP4)

History in a Crisis − Lessons for Covid-19

Origin and evolution of pathogenic coronaviruses

China Novel Coronavirus Investigating ACS Sensors pubs.acs.org/acssensors Article

A Novel Coronavirus from Patients with Pneumonia in China

Respiratory Virus Infections: Understanding COVID-19

Diagnostic accuracy of serological tests for covid-19: systematic review and meta-analysis

Negative Nasopharyngeal and Oropharyngeal Swabs Do Not Rule Out COVID-19. Negative Nasopharyngeal and Oropharyngeal Swabs Do Not Rule Out COVID-19

Satchi-Fainaro, R. Immune-mediated approaches against COVID-19

The researchers taking a gamble with antibody tests for coronavirus

Integrated hand-powered centrifugation and paper-based diagnosis with blood-in/answer-out capabilities

Paper-Based 3D Scaffold for Multiplexed Single Cell Secretomic Analysis

Recent Progress in Microfluidics-Based Biosensing

Paper based diagnostics for personalized health care: Emerging technologies and commercial aspects

Smartphone-based analytical biosensors

Three-dimensional paper-based microfluidic chip device for multiplexed fluorescence detection of Cu 2+ and Hg 2+ ions based on ion imprinting technology

A fully integrated distance readout ELISA-Chip for point-of-care testing with sample-in-answer-out capability

Reinventing (Bio)chemical Analysis with Paper

Three-dimensional paper-based electrochemiluminescence immunodevice for multiplexed measurement of biomarkers and point-of-care testing

Paper-Based Device for Colorimetric and Photoelectrochemical Quantification of the Flux of H2O2 Releasing from MCF-7 Cancer Cells

Paper-based chemiluminescence ELISA: Lab-on-paper based on chitosan modified paper device and wax-screen-printing

Hand-powered ultralow-cost paper centrifuge

A fidget spinner for the point-of-care diagnosis of urinary tract infection

Blood Plasma Separation Using a Fidget-Spinner

The Architecture of SARS-CoV-2 Transcriptome

SARS-CoV-2 Cell Entry Depends on ACE2 and TMPRSS2 and Is Blocked by a Clinically Proven Protease Inhibitor

Structure of the SARS-CoV-2 spike receptor-binding domain bound to the ACE2 receptor

COVID-19: immunopathology and its implications for therapy

Structure and function of immunoglobulins

Immune Response, Inflammation, and the Clinical Spectrum of COVID-19

Role of natural and immune IgM antibodies in immune responses

The phosphatase PAC1 acts as a T cell suppressor and attenuates host antitumor immunity

Serum IgA, IgM, and IgG responses in COVID-19

Profiling Early Humoral Response to Diagnose Novel Coronavirus Disease (COVID-19)

Characteristics and roles of SARS-CoV-2 specific antibodies in patients with different severities of COVID-19

The strategy of antibody-free biomarker analysis by in-situ synthesized molecularly imprinted polymers on movable valve paper-based device

ZnSe quantum dot based ion imprinting technology for fluorescence detecting cadmium and lead ions on a three-dimensional rotary paper-based microfluidic chip

Characterization of SARS-CoV-2-specific antibodies in COVID-19 patients reveals highly potent neutralizing IgA

Fibroblast-stimulating lipopeptide-1 as a potential mucosal adjuvant enhances mucosal and systemic immune responses to enterovirus 71 vaccine

Serum and mucosal antibodies fail as prognostic markers during critical influenza A infection

Duration of antibody responses after severe acute respiratory syndrome

White-Al Habeeb, N. Canadian society of clinical chemists (CSCC) interim consensus guidance for testing and reporting of SARS-CoV-2 serology

Serological immunochromatographic approach in diagnosis with SARS-CoV-2 infected COVID-19 patients

An evaluation of COVID-19 serological assays informs future diagnostics and exposure assessment

Analytical and clinical validation of an ELISA for specific SARS-CoV-2 IgG, IgA, and IgM antibodies

Diagnostic methods and potential portable biosensors for coronavirus disease 2019

DNA nanoscaffold-based SARS-CoV-2 detection for COVID-19 diagnosis

Rapid lateral flow immunoassay for the fluorescence detection of SARS-CoV-2 RNA

Performance of Radiologists in Differentiating COVID-19 from Non-COVID-19 Viral Pneumonia at Chest CT

Multiplexed Nanomaterial-Based Sensor Array for Detection of COVID-19 in Exhaled Breath

The authors declare no competing financial interest.