key: cord-0840806-ih2z2nt1 authors: Ciğeroğlu, Zeynep title: Preparation of ZnO/BaTiO(3) adsorbent using Elaeagnus Angustifolia L. leaf extract and its evaluation for ciprofloxacin removal from aqueous solutions: an optimization study date: 2021-05-22 journal: Biomass Convers Biorefin DOI: 10.1007/s13399-021-01593-9 sha: 1a808d9165a696ba075e83dac6e567dec72b2a2c doc_id: 840806 cord_uid: ih2z2nt1 Especially, most papers have reported an increase in antibiotic resistance (AR) bacterial infections during the COVID-19 pandemic. Because of the outbreak of the SARS-CoV-2, antimicrobial resistance (AMR) should be controlled and reduced. Researchers have reported that the adsorption technique is an sufficient procedure for separating drugs such as antibiotics from aqueous solutions. The prepared of ZnO/BaTiO(3) nanocomposite using Elaeagnus Angustifolia L. leaf extract was successfully obtained using green route. The synthesized nanocomposite was interacted with ciprofloxacin hydrochloride (CPF) to aim at eliminating the antibiotic from aqueous solutions. The incorporation of Elaeagnus Angustifolia leaf extract onto ZnO/BaTiO(3) proved a sustainable chemistry study. Hence, this study indicated that green nanoparticles include neither the use of hazardous chemicals nor toxic chemicals. FTIR, XRD, and SEM-EDX analyses were applied to give information about the structural properties of the green nanocomposite. Box-Behnken design (BBD) was executed by response surface methodology (RSM) to gain optimal conditions. The effect of pH, initial concentration of CPF, and nanocomposite dose on CPF-nanocomposite interaction was examined. The experimental findings of adsorption study revealed that the optimal adsorption capacity of CPF onto ZnO/BaTiO(3) was found as 125.29 mgg(-1) under optimal conditions (adsorbent dose: 3.00 mg, pH value of solution: 9.88, initial concentration CPF: 49.63 mgL(-1)). Nowadays, antibiotic resistance (AR) is a severe topic that affects global health. Antibiotics are designed to defeat bacteria and microorganisms. These antibiotics, taken uncontrollably and unconsciously, cause the bacteria and microorganisms to gain resistance and create bacterial resistance. There are many reasons that accelerate the spread of AR. AR arises from discharging antibiotics into agricultural land, drinking water and sewage [1] . Ciprofloxacin (CPF), a second-generation fluoroquinolone, has broad-spectrum antibiotic owing to its widespreaduses in treatment for both gram-positive and gram-negative bacteria [2] . It can be used therapeutically for the lower respiratory tract, urinary tract, especially bladder infection, bone infection such as osteomyelitis, intra-abdominal infection urinary tract, skin-related infections, neutropenic patients [3] . One of the solution ways against antibiotic resistance is the process of removing antibiotics from aqueous solutions. Many techniques have been progressed to eliminate antibiotics from the aqueous phase. These are membrane technology [4] , Fenton oxidation [5] , photocatalytic degradation [6] , electrocoagulation [7] and adsorption [8] . Among these techniques, adsorption stands out because it is the easiest, cheapest and most applicable process. Zinc oxide (ZnO) has drawn great attention owing to its nature such as low cost, non-toxic, thermal stability [9] . Nagpal and Kakkar (2019) underlined in their review that ZnO NPs are used in wastewater treatment due to the reasons aforementioned above [10] . Nowadays, green chemistry processes in the preparation of nanoparticles are becoming more and more popular thanks to environmentally benign manufacturing. Especially, the synthesis of nanoparticles via plant extracts makes them more biocompatible [11] . Published papers related to ZnO nanoparticles exemplified the promising application of the green synthesis method [12] [13] [14] . BaTiO 3 is a common photocatalyst owing to the semiconductor material. When the studies in the literature were examined, it was seen that BaTiO 3 was scarcely used in the adsorption process. Kumari et al. (2015) prepared BaTiO 3 -mesoporous silica nanocomposite for the extract of Cr 6+ from water [15] . Therefore, ZnO/BaTiO 3 has been used for the first time in CPF adsorption. Phytochemicals are compounds such as polyphenols, phenolic acids, and flavonoids. They contribute significantly in the reduction of metallic ions [16] . Elaeagnus Angustifolia known as the Russian olive has numerous phytochemicals such as flavonoids, polyphenols, phenolic acids and vitamins [17] . It is used for the treatment of ulcer, sore throat, asthma treatment, and bronchial and lung diseases [18, 19] due to its antioxidant, anticonvulsant, analgesic, and anti-inflammatory properties [17] . Response surface methodology (RSM) is widely chosen to figure out the impacts of the inputs on outcomes. RSM is a helpful statistical technique. It indicates how the responses change in the selected input range. Besides, it helps to optimize the response [20] . In this context, the ultrasound-assisted extraction method was preferred to prepare Eleagnus Angustifolia L. leaf extract. The prepared ZnO/BaTiO 3 with the help of Eleagnus Angustifolia L. leaf extract was used for the elimination of CPF from aqueous solutions. The secondary aim was to construct adsorption conditions containing three factors such as pH, adsorption dose, and initial concentration of CPF using RSM integrated into Box-Behnken design (BBD). Therefore, RSM was predicted to be the most suitable optimal CPF adsorption conditions, which gave the highest adsorption capacity onto ZnO/BaTiO 3 . Both variance analysis (ANOVA) and Pareto chart were applied in order to show the impacts of inputs on the outputs. Besides, the changes of the adsorbent surface after adsorption were described using by ATR-FTIR spectroscopy. Hence, the surface morphology of the adsorbent and adsorption mechanism were illuminated. ZnO (99.99 %, 18 nm) and BaTiO 3 (99.95 %, 90 nm, cubic) were purchased from Nanografi (ODTU Teknopark, Turkey). Fig. 1 The representation of the preparation of ZnO/BaTiO 3 using Elaeagnus Angustifolia leaf extract as a solvent Elaeagnus Angustifolia L. leaves were obtained from İzmir, Turkey in 2020. First, Elaeagnus Angustifolia L. leaves were ground by using a grinder. Then, a homogenizer (Bandelin, Sonoplus HD 2200.2) with 13 nm titanium probe was used to extract Elaeagnus Angustifolia L. leaf. Briefly, 30 mL of distilled water was poured into 0.75 g of grinding leaves. The sonicater was operated with a 70% amplitude (50% nominal) during 10 min. Then, the extracts were filtered using RC filter, 20 μm. 20 mL of extracts were added to the beaker and BaTiO 3 by taking 50 % of the weight of ZnO and ZnO were added. The solution was mixed by magnetic stirrer at a speed of 400 rpm. Absolute ethanol was used as the washing solution. After the nanoparticle was washed three times and was dried at 60 o C in a vacuum dryer until it dries. The dried material was calcinated at 550°C during 5 h at a heating rate of 10°C. Figure 1 represented the preparation of ZnO/BaTiO 3 using Elaeagnus Angustifolia leaf extract as a solvent. Spectrum Two FT-IR Spectrometer (FTIR) (Perkin Elmer) was applied to describe the functional groups of the prepared ZnO/BaTiO 3 nanocomposite. Scanning electron microscopy (SEM) with energy dispersive X-ray analysis (XL-30 SFEG, Philips, Eindhoven, Holland) was performed to illuminate the surface analysis of the samples. X-ray diffraction (XRD) analyses were done using (Bruker D8 Advance device) via Cu Kα radiation over a 2θ range from 2-90°with the scanning rate of 3°min -1 . The design of adsorption runs were constructed using Design Expert 12 software ((Trial version 12, Stat-Ease, USA). The desired adsorbent dose was added to Erlenmayer and the specified initial antibiotic solution was poured into the Erlenmayer. Then, shaker was run at the speed of 100 rpm for two hours. Two hours later, the initial and final solution were read at 275 nm by using a UV-Vis Spectrophotometer (Pekin Elmer, Lambda 365, USA). The adsorption capacity was calculated in Eq. (1) as follows; In Eq. (1), qe is the adsorption capacity (mg g -1 ), C o is the initial CPF concentration in solution (mgL -1 ), C f is the final concentration in 2 h later (mgL -1 ), m is the mass of ZnO/ BaTiO 3 (g), and V is the solution volume (L). Response surface methodology (RSM) was preferred in order to optimize the adsorption process conditions. RSM suggested a mathematical model indicating the process conditions. By using this mathematical equation in coded factor in Eq. (2) . where α 0 is the intercept, α i is a single factor, α ij is the interaction of factors and ε is a pure error. The evaluation of the percentage effect (P %) of each variable on the adsorption capacity could be drawn Pareto chart by following Eq. (3) [21] . In Eq. (3), α i is the coefficient of variables in Eq (2) in accordance with coded factor, P i is the percentage of each variable, respectively. In order to assess the impacts of the inputs (pH, CPF initial concentration and adsorbent dose) on the response (adsorption capacity), BBD design was selected. Box and Behnken devised Box-Behnken design in 1960 [22] BBD is an alternative method instead of a full factorial design serving labor efficiency with fewer essential experiments [23] Fig. 2 . In FTIR spectrum of BaTiO 3 , a peak appeared at 511 cm -1 corresponding to a common Ti-O absorption into BaTiO 3 [24] . Additionally, a small peak at 3500 cm -1 was assigned to asymmetric and symmetric -OH bond. In ZnO FTIR's spectrum depicted that a small peak at 687 cm -1 was attributed to the Zn-O stretching bond [25] . FTIR spectrum of the synthesis ZnO/BaTiO 3 showed that the peak at around 498 cm -1 was the characteristic bond of Ti-O vibration [26] . The other small intensity peak at about 1400 cm -1 was related to the crystalline Ba-Ti-O vibration [27] . The small (C = O) p (p :pyridone) vibrations of CPF was seen at 1630 cm -1 in the spectrum of CPF-adsorbed ZnO/BaTiO 3 [28] . The other small peak emerged at 1260 cm -1 owing to the vibration of C-F bond of CPF [28] . This result showed that electrostatic interactions occurs between raw CPF and ZnO/BaTiO 3 . Briefly, it was seen that there is a strong overlapping between the spectrum of CPF-adsorbed ZnO/ BaTiO 3 and the spectrum of pure ZnO/BaTiO 3 . [30] . The peaks related to BaTiO 3 and ZnO were seen in the XRD pattern of ZnO/BaTiO 3 . SEM image of pure BaTiO 3 nanoparticle showed quasispherical shape in Fig. 4(b) . Besides, the surface of BaTiO 3 had less agglomerated. The agglomeration form of ZnO appeared in Fig. 4(a) . In addition, the spherical shape of ZnO nanoparticles occurred. Both the spherical shape of ZnO and the quasi-spherical shape of BaTiO 3 belonging to the synthesized ZnO/BaTiO 3 were seen in Fig. 4(c) . It might be claimed that a new surface occurred. A well-synthesized form of the BaTiO 3 and ZnO was observed from the SEM-EDX result. Seventeen runs with five replicates at center points were shown in Table 2 . Through the ANOVA analysis ( with the F and p-value indicates which parameter is more crucial than the others. The most effective variable was seen as pH (F-value: 229.19 and p-value<0.0001). It can be sorted by other effective parameters as follows; dose of nanoparticle (B), CPF initial concentration (C), and the squared dose of nanoparticle (B 2 ). In addition to variance analysis, Pareto chart serves as a better understand which parameter is more significant than the others. Hence, Pareto chart implies the percentage values of factors that are statistically crucial. The mathematical equation in terms of coded factor was obtained as the following Eq. (4). The Pareto graph of the independent factors was drawn with the help of Eqs. (3) and (4) . Looking at the Pareto chart in Fig. 5 , the most influential factor was seen as A: (25.28%). Then, the other impacted parameters could be listed as the squared adsorbent dose (B 2 : 22.09%), adsorbent dose (B: 21.55), CPF initial concentration (C: 16.62%). The suggested model is well-fitted to the adsorption data because the lack of fit (LOF) is not significant (p-value=0.0579) and this value is also related to pure error containing replicates at center points. The higher R 2 value (0.9906) demonstrated a higher regression between the proposed data and empirical results. The obtained higher R 2 -adj (0.9786) showed a reliable correlation. The difference between R 2 -adj and R 2 -pred was calculated as 0.1037. This value implied that the suggested model estimated the outcomes properly. Generating 3-D surface graphs allow researchers to interpret the relationships between dependent and independent parameters more easily. The desired maximum adsorption capacity was found as 125.29 mgg -1 under optimal conditions such as the adsorbent dose: 3.00 mg, pH value of the solution: 9.88, initial concentration CPF:49.63 mgL -1 . Adsorption studies have revealed that pH of the solution plays an effective factor on adsorption mechanism as a result of the surface charge of the adsorbent is varied with pH [31] . While the pH value of the solution was increasing, the adsorption capacity of CPF onto ZnO/BaTiO 3 was increased. The adsorption capacity was obtained from 57 to 126 mgg -1 from pH 4 to pH 10 ( Fig. 6 (a)-(b) ). Similar result was recorded by Sun et al. (2016) [32] . In order to explain the higher adsorption Fig. 6 The binary interaction of inputs on qe a) pH-adsorbent dose, b) pH-initial CPF concentration, c) adsorbent dose-initial CPF concentration under optimal conditions (adsorbent dose: 3.00 mg, pH value of solution: 9.88, initial concentration CPF: 49.63 mgL -1) capacity in basic pH, it is necessary to know the pKa values of the CPF antibiotic. CPF has two pKa values, which are pKa 1 : 5.90 and pKa 2 : 8.89 owing to the presence of the carboxyl group and amine groups in piperazine ring, respectively [33] . Thus, three different forms such as cationic CPF + (pK a1 ), zwitterionic CPF± (between the pK a1 and pK a2 ) and anionic CPF − (pK a2 ) occurred [34] . Thus, the electrostatic interaction between the anionic adsorbate and cationic charged adsorbent occurred in basic pH. While varying ZnO/BaTiO 3 dose value from 3 mg to 9 mg, the adsorption capacity was decreased ( Fig. 6 (a)-(c) ). Obviously, the higher adsorption capacity is obtained by using the lesser adsorbent dose. Besides, increasing the amount of adsorbent brings about both the aggregation of green adsorbent and the improvement of electrostatic repulsive force between green nanoparticles [35] . Thus, CPF molecules are difficult to interact with the adsorbent. Similar data were recorded by Yu et al. (2018) [36] and Li et al. (2017) [37] . Numerous CPF concentrations (20-50 mgL -1 ) were prepared to assess the impact of initial CPF concentration on the adsorption process. The higher adsorption capacity was gained, when the initial CPF concentration was 50 mgL -1 ( Fig. 6 (b)-(c) ). This situation is clearly explained that, a high initial concentration of CPF results in higher concentration gradient owing to the driving force [38] . Thus, CPF molecules were adsorbed faster to the surface of ZnO/BaTiO 3 . However, the rapid increment of adsorption capacity was gradually decreased after the certain CPF initial concentration, because of the saturation of adsorbent's active sites by higher concentration of CPF [39] . The repulsion between the CPF and adsorbent happens by the virtue of the occupation of CPF onto available sites of adsorbent [40] . The high qe of adsorbent is a crucial factor for the utilization of the adsorbent from an economic point of view. ZnO/ BaTiO 3 exhibited a good adsorbent for the adsorption of CPF. The measured qmax for ZnO/BaTiO 3 and green adsorbents recorded in the literature were summarized in Table 4 . Hence, ZnO/BaTiO 3 is a promising adsorbent and can be used for the removal of antibiotics. To sum up, this work examined the valorization of Elaeagnus Angustifolia L. leaf as a high potential reducing agent to prepare ZnO/BaTiO 3 nanoparticles. The leaves, which are also described as biowaste, were extracted by selecting the innovative extraction method. Thus, the ultrasound-assisted extraction method offers less extraction time, lower energy consumption, and lower solvent consumption. In this context, the extraction method chosen is also an environmentally friendly method. Box-Behnken design (BBD) gives a better outcome for optimization by reducing the number of experiments. The effects of pH, initial concentration of CPF, nanocomposite dose on CPF-nanocomposite interaction were examined as independent factors. The maximum adsorption capacity of CPF onto ZnO/BaTiO 3 was found as 125.29 mgg -1 under optimal conditions (adsorbent dose:3.00 mg, pH value of solution: 9.88, initial concentration CPF:49.63 mgL -1 ). Pareto graph was indicated that the most influential factor was pH (25.28%). Effect of River Landscape on the sediment concentrations of antibiotics and corresponding antibiotic resistance genes (ARG) 1) New classification and update on the quinolone antibiotics Prophylaxis of bacterial infections with ciprofloxacin in patients undergoing bone marrow transplantation Effect of wastewater colloids on membrane removal of antibiotic resistance genes The use of artificial neural network (ANN) for modeling of COD removal from antibiotic aqueous solution by the Fenton process Photocatalytic degradation of amoxicillin, ampicillin and cloxacillin antibiotics in aqueous solution using UV/TiO2 and UV/H2O2/TiO2 photocatalysis Optimization of electrocoagulation process for efficient removal of ciprofloxacin antibiotic using iron electrode; kinetic and isotherm studies of adsorption Efficient removal of antibiotics by a novel magnetic adsorbent: Magnetic activated carbon/chitosan (MACC) nanocomposite Investigations of thermoelectric properties of ZnO monolayers from the first-principles approach Use of metal oxides for the adsorptive removal of toxic organic pollutants Plant extract synthesized silver nanoparticles: An ongoing source of novel biocompatible materials A facile green synthesis of ZnO nanoparticles and its adsorptive removal of Congo red dye from aqueous solution Green synthesis of ZnO nanoparticles using Solanum nigrum leaf extract and their antibacterial activity Laurus nobilis leaf extract mediated green synthesis of ZnO nanoparticles: Characterization and biomedical applications Mesoporous BaTiO 3@ SBA-15 derived via solid state reaction and its excellent adsorption efficiency for the removal of hexavalent chromium from water Green" nanotechnologies: synthesis of metal nanoparticles using plants Russian olive (Elaeagnus angustifolia L.): From a variety of traditional medicinal applications to its novel roles as active antioxidant, anti-inflammatory, antimutagenic and analgesic agent Effect of Aqueous Extract of Elaeagnus angustifolia Fruit on Experimental Cutaneous Wound Healing in Rats Elaeagnus angustifolia and its therapeutic applications in osteoarthritis Application of Box-Behnken design and response surface methodology for modeling and optimization of batch flotation of coal Response surfaces: designs and analyses Some New Three Level Designs for the Study of Quantitative Variables Investigation of the effects of biodiesel/2-ethylhexyl nitrate (EHN) fuel blends on diesel engine performance and emissions by response surface methodology (RSM) An Eco-Friendly Method of BaTiO3 Nanoparticle Synthesis Using Coconut Water Sb2O3-ZnO nanospindles: A potential material for photocatalytic and sensing applications Impact of ZnO addition on structural, morphological, optical, dielectric and electrical performances of BaTiO3 ceramics Tetragonal BaTiO3 nanoparticles: An efficient photocatalyst for the degradation of organic pollutants Effect of particle size of calcium phosphate based bioceramic drug delivery carrier on the release kinetics of ciprofloxacin hydrochloride: an in vitro study Improved photoluminescence, thermal stability and temperature sensing performances of K + incorporated perovskite BaTiO 3 : Eu 3+ red emitting phosphors Zinc oxide nanoparticles selectively induce apoptosis in human cancer cells through reactive oxygen species Cr(VI) removal from synthetic wastewater using coconut shell charcoal and commercial activated carbon modified with oxidizing agents and/or chitosan Characterization and ciprofloxacin adsorption properties of activated carbons prepared from biomass wastes by H3PO4 activation Influence of pH and antibiotic solubility on the removal of ciprofloxacin from aqueous media using montmorillonite Sorption of the Antimicrobial Ciprofloxacin To Aluminum and Iron Hydrous Oxides Hydrothermal synthesis of LaFeO3 nanoparticles adsorbent: Characterization and application of error functions for adsorption of fluoride Adsorptive removal of ciprofloxacin by ethylene diaminetetraacetic acid/β-cyclodextrin composite from aqueous solution Zeolitic imidazolate framework-8 derived nanoporous carbon as an effective and recyclable adsorbent for removal of ciprofloxacin antibiotics from water Fast and effective methylene blue adsorption onto graphene oxide/amberlite nanocomposite: Evaluation and comparison of optimization techniques Modeling of adsorption of Methylene Blue dye on Ho-CaWO4 nanoparticles using Response Surface Methodology (RSM) and Artificial Neural Network (ANN) techniques Synthesis and characterization of MgO supported Fe-Co-Mn nanoparticles with exceptionally high adsorption capacity for Valorization of biomass into amine-functionalized bio graphene for efficient ciprofloxacin adsorption in water-modeling and optimization study Hematite dysprosium oxide nanocomposites biosynthesized via greener route for ciprofloxacin removal and antimicrobial activity An efficient adsorbent: Simultaneous activated and magnetic ZnO doped biochar derived from camphor leaves for ciprofloxacin adsorption Publisher's Note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations Acknowledgements The author would like to thank Bilim Pharmaceuticals for support Ciprofloxacin HCl.