key: cord-0765193-h0ggn02k
authors: Zhou, Pei; Yang, Yi; Huang, Gongsheng; Lai, Alvin C.K.
title: Numerical and experimental study on airborne disinfection by negative ions in air duct flow
date: 2017-11-06
journal: Build Environ
DOI: 10.1016/j.buildenv.2017.11.006
sha: 133d0aa7517a273c814e6ebc2f80cb5e8c3aac53
doc_id: 765193
cord_uid: h0ggn02k

In this paper, we develop a mathematical model that aims (1) to predict the distribution of negative ions generated by an air ionizer installed in a ventilation duct and (2) to predict the efficiency with which it inactivates bacteria. The transportation equation for the negative ions was resolved combined with the bulk air velocity and the electric field. The bacteria distribution was solved numerically by integrating the susceptibility constant, which was acquired from the experiments. Two types of bacteria (Serratia marcescens, Staphylococcus epidermidis) were aerosolized and released into a 9-m ventilation duct system. Inactivation efficiencies were calculated for inlet velocities from 2 to 6.5 m/s and for various ion intensities. The efficiencies for S. marcescens and S. epidermidis were 31.53% (SD, 11.4%) and 12.17% (SD, 0.43%), respectively, with susceptibility constants of 8.67 × 10(−11) Colony-Forming Units (CFU)/ions and 2.72 × 10(−11) CFU/ions, respectively. The modeling results matched those of the experiments well. The pressure penalty at the maximum velocity (6.5 m/s) was only 9 Pa. The results show that the use of negative ions has great potential to enhance indoor air quality by reducing airborne microorganisms in ventilation systems.

According to the US Environmental Protection Agency, indoor air quality (IAQ) is one of the five most urgent environmental risks to public health [1] . Heating, ventilation, and air conditioning (HVAC) systems play a vital role in ensuring the indoor air quality inside such environments. Outbreaks of severe infectious diseases, from severe acute respiratory syndrome in 2003 to avian influenza and Middle East respiratory syndrome in recent years, indicate the importance of effective disinfection in ventilation systems to prevent extensive infections inside a building [2, 3] . Ductwork systems provide a breeding ground for the potential reproduction and transmission of microorganisms [4] . Such microorganisms can survive and propagate throughout the entire building through sophisticated, interconnected ventilation duct systems, which may be lead to cross-infection of the occupants.

Conventional solutions for improvement of indoor microorganism levels are filtration or dilution. Commonly used medium-grade filters (minimum efficiency reporting value (MERV) of 8-10) are not effective in removal of small bacteria and viruses. In addition, filters can support active microbial growth if sufficient nutrients are present [5] . Energy considerations generally prevent the use of high-efficiency particulate air (HEPA) filters in commercial buildings.

Thus, to balance energy consumption and IAQ, in addition to physical removal approaches such as filtration and dilution, chemical/ biological-based approaches for inactivation of airborne microorganisms have recently been developed and applied in HVAC systems. An alternative method using air ionizers for disinfection was developed in recent years. Park et al. [6] demonstrated the feasibility of the air ion disinfection approach for the reduction of aerosol particles in HVAC systems and found that this approach can be used to control IAQ. They showed that it is feasible to remove bioaerosols with a low-efficiency HVAC filter enhanced by continuous emission of unipolar air ions. Lee et al. [7] [8] [9] conducted similar experiments to determine the disinfection performance of air ions against aerosolized bacteria. Unipolar and bipolar ionizers were installed in a duct flow to evaluate the disinfection efficacy with different numbers of ionizers and the polarity effect.

There is an important parameter characterizes the susceptibility of bacteria disinfected with this kind of chemical/biological approach. It is often denoted as the susceptibility constant, Z, and its value depends primarily on complex biological characteristics of the airborne bacteria and the environmental conditions. Without knowing Z, it is not possible to predict the disinfection performance. Our group previously measured Z for a few bacteria under UV-C irradiation [10] .

The disinfection mechanism of bacteria by air ions is usually summarized as a generated electrostatic force. Fletcher et al. proposed that unrecoverable electroporation plays a role in the disinfection effect of air ions [11, 12] . Mendis et al. [13] proposed and modeled an electrophysical mechanism that involves the electrostatic disruption of a cell membrane. Digel et al. [14] explained the antimicrobial action of ions as a chemical modification of the surface proteins of bacteria. It is clear that the inactivation mechanism against microorganisms by air ions is still controversial.

There are a few experimental studies with air ionizers that aim to disinfect different types of bacteria, very few numerical studies were reported as well. Noakes et al. [15] and Fletcher et al. [12] developed a two-dimensional (2D) model to simulate the performance of negative ionizers in ventilated rooms, in which the electric field and ion balance equations were treated as user scalars and solved by a commercial computational fluid dynamics (CFD) tool. Mayya [16] developed a detailed mathematical model of air ions by considering the electric field, particle charging, ion transport, and wall loss. However, none of these studies modeled the disinfection of bacteria. In Ref. [17] , a semiempirical formula based on experiment results was applied to simulate the distribution of the bacteria Escherichia coli. However, the susceptibility constant was not measured; it was only determined by a trialand-error approach. To model airborne bacteria, an additional "phase" must be considered in which the bacteria can be treated as particles and modeled by either the Eulerian or Lagrangian approach [18] . Eulerian approach has been applied previously by the present authors and the others for modeling disinfection of bacteria [19, 20] , thus in this paper Eulerian approach was adopted.

The literature listed above carried out experimental studies or modeled the particles separately. None of them combined modeling of ion transport and measurement of inactivation. Thus, the accuracy of the modeling could not be validated experimentally. Moreover, many studies used negative ionizers in very small tubes or at low velocities [9] . The results therefore may not be applicable for practical ventilation systems. Thus, this paper provides a mathematical model of negative ions and bacteria distribution in a ductwork system. Experiments were also carried out to validate the modeling prediction, and susceptibility constants for two bacteria were also determined. Safety concern on ozone emission is also discussed.

The detailed experimental setup can be found elsewhere [21] , and thus only a brief description is reported here. The designed ductwork was 9 m long and made of 200 mm × 200 mm modular galvanized steel. Fig. 1 includes a picture and a schematic of the test bed.

First, the emission system plays an important role in generating and delivering the bacteria. In this study, it consisted of a compressor and a nebulizer (24 jet, Collision Nebulizer, BGI). The pretreated filtered air was first compressed into the nebulizer, which was used to aerosolize the test bacteria (S. marcescens and S. epidermidis).

Second, the aerosolized bacteria were delivered to the inlet of a centrifugal fan inside a tailor-made plastic box. The plastic box was equipped with a HEPA filter to prevent contaminated air from entering the ducting from the laboratory. The fan speed was adjusted between 1.5 and 6.5 m/s with a switch. The bacteria were pushed throughout the 9-m-long ductwork. A negative ionizer (VI-2500, Wein Products Inc. Los Angeles) was used as the air ion source. An ion counter with a measuring range up to 1.99 × 10 8 ions/cc (Air Ion Counter, AlphaLab, Utah) was used to measure the emission concentration. The ion counter was placed inside the duct, and the ion intensity was output as voltage and recorded. Two single-stage viable Andersen cascade impactors (N6, Thermo Scientific) were used to sample the bacteria concentration upstream and downstream of the ionizer. The sampling points for collecting the bacteria were located 0.3 m before and 0.9 m after the ionizer (see Fig. 1 ).

The pressure drop caused by the ionizer was evaluated by comparing the static pressure upstream with that downstream between the ionizer, and the static pressure was measured with a pressure transducer (DPT2641, Setra, USA) with an accuracy of ± 1%. The duct length between the two measuring locations was 1.40 m; the measuring locations are denoted as solid black points labeled "A" and "B" in Fig. 1 . The pressure measurement locations were coincident with the upstream bacteria sampling point and the ion measurement point, but the experiment for each was conducted separately. The initial static pressure without the ionizer was measured, and the values were measured again after the ionizer was inserted. The differences between the pressures are referred to the ionizer's pressure drop (ΔP).

Another HEPA filter was placed at the exit of the duct to prevent the bacteria from contaminating the laboratory. The operating environment was very stable, and the air temperature was maintained at 23°C ± 0.5°C with a relative humidity of 55% ± 2%.

The operation mainly consisted of three procedures: the preparation of test bacteria, the measurement of negative ions, and the sampling of the bacteria to calculate the inactivation efficacy. The Gram-negative bacteria S. marcescens (ATCC 6911) and Gram-positive bacteria S. epidermidis (ATCC 12228) were selected to test the disinfection efficiency of the negative ionizer. The pathogens were atomized and aerosolized by the nebulizer with an inlet pressure of 275.8 kPa.

The ion generation probe of the negative ion generator was inserted inside the ductwork through an 8-mm-diameter circular opening. The ion intensity was regulated by setting the input voltages (6-12 V) . In this experiment, only one air velocity was tested: 3 m/s. The number of negative ions was measured at different locations downstream of the duct system (0.95, 1.30, 1.65, 2.55, 2.90, 3.45, and 4.5 m from the ductwork inlet). Because it was impossible to directly contact the surface of the ion generator to obtain the real "emission rate," which is required as a boundary condition setup for the ionizer, the air ion counter was placed 5 cm downstream from the ionizer to obtain the maximum ion concentration for the purpose of determining the ionizer's boundary conditions. The ion counter was carefully placed in the center of the duct, and the sampling opening was placed perpendicular to the airflow.

For bacteria disinfection experiments, a variable speed-controlled fan was used to deliver filtered air mixed with bacteria. The steady air stream was controlled at speeds of 3.0, 4.0, 5.0, 6.0, and 6.5 m/s by monitoring the fully developed speed at a point 4 m downstream of the fan. Each impactor was connected to a vacuum pump, and the sampling flow rate was set to 28.3 L/min. The sampling time was set to 106 s with an equal total sampled air volume of 50 L. For each velocity, each bacteria was repeated at least 10 times. The disinfection efficacy was calculated by the following equation:

where CFU down and CFU up are the colony-forming units (CFUs) of bacteria from the upstream and downstream regions of the ionizer, respectively, as shown in Fig. 1 . After cultivating both S. epidermidis and S. marcescens for 24 h, the CFUs were counted and the disinfection efficacy was calculated.

The modeling in this study was done by a commercial CFD tool, ANSYS-FLUENT. The potential difference, the electrical field, and the negative ions were treated as scalars in FLUENT. The governing equations are written as follows:

(2)

The potential, given in Eq. (2) , and the electrical field, given in Eq. (3), are governed by Poisson and Gauss's equations respectively. Φ is the potential of the plasma unit, V, e is the elementary charge, 1.6 × 10 −19 C, ε 0 is the permittivity of free space, 8.854 × 10 −12 C 2 / Nm 2 , E is the electric field, V/m, n is the negative ion concentration, ions/m 3 , u is the air flow velocity in the ventilation duct, m/s, μ p is the ion mobility, 1.35 × 10 −4 m 2 /Vs, and D p represents the ion diffusion coefficients, 3.5 × 10 −6 m 2 /s; the specific values in above parameters can be found in Refs. [15, 16] . Thus, the negative ion equation (Eq. (4)) was solved after the convergence of the Navier-Stokes equations.

The electrical force generated by the charged particles will affect the air flow by adding a source term on the momentum [15] ; see Eq. (5), where ρ is the density of air, kg/m 3 , μ is the dynamic viscosity, N·s/m 2 , and P is the pressure, Pa.

The continuity equation for the bacteria concentration can be written as:

where C i is the particle concentration of a particular particle size in group i, CFU/m 3 , v s,i is the particle-settling velocity, m/s, ε p is the particle eddy diffusivity, m 2 /s; for small particles it is assumed that ε p / v t =1, where v t is the turbulent fluid viscosity. D i is the Brownian diffusion coefficient, m 2 /s. The settling velocity and Brownian diffusion coefficient can be calculated according to reference [22] . Eq. (7) was retrieved from Refs. [20, 23, 24] for modeling the disinfection of airborne bacteria using UVGI sources. In this study, it was adapted to simulate the bacteria "reacting" to the ion intensities. S i is the source term, which includes two parts: bacteria deposition onto walls, S d , and bacteria disinfected by negative ions, S ion .

Eq. (8) and Eq. (9) have been used by the authors [10] . The summation term in Eq. (8) is the sum of all the faces of the immediate layer near the wall. The term v d is the deposition velocity, which was calculated by the three-layer model developed by Lai and Nazaroff [25] , m/s. A w is the normal vector area of the cell face, m 2 , and V cell is the cell volume, m 3 . The drift flux model [18, 26, 27 ] was applied to model bacteria dispersion and deposition onto the internal wall surface due to gravity and Brownian and turbulent diffusion. The density of both bacteria was assumed to be 1400 kg/m 3 [17] . It is noted that the natural decay of the bacteria was not considered in the model since the sampling point before and after ionizer is relatively short, only 1.2 m in this study. As the diameters for S. marcescens and S. epidermidis in this study were less than 1.0 μm, together with the velocity tested, the dimensionless relation time is in the order of 10 −2 , thus turbophoresis can be ignored without causing any significant error [28] .

Eq. (9) can be used to describe the bacteria disinfected due to the presence of ions. C 0 is the initial concentration of airborne bacteria, which is equal to the upstream concentration, CFU/m 3 , Z is the microorganism susceptibility constant under negative ions, CFU/ions, and N ion is the number of negative ions that reached a single bacteria, ions/ CFU, which can be expressed by Eq. (10) [29] .

i c a p t u r e c a p t u r e (10) t expoure is the bacteria exposure time by ion and t capture is the bacteria capturing time. The term t exposure was calculated by using Eq. (11), where d is the distance between the ionizer and the sampling point; in this study, d was 0.9 m. The sampling time, t capture , was 106 s in this case. Q exposure is the flow rate when the bacteria is exposed to the ions, which can be expressed by Eq. (12), m 3 /s. Here, A refers to the cross area of the ductwork. Q capture is the sampling flow rate, which was 28.3 L/min. (12) It is noted that t exposure equals t in Eq. (9) because the duct is filled with negative ions and the exposure time is approximately equivalent to the length of time that bacteria is exposed by the ions in the duct. Then, Eq. (9) can be rewritten as follows: (13) where the constant 2.419 was calculated by Q exposure /(Q capture × t capture ).

The key issue becomes how to obtain the constant Z. It can be determined by considering the surviving fraction of airborne microorganisms exposed to negative ions in a ventilated room [29] :

on off ion (14) where C off is the initial concentration of airborne microorganisms, C on is the average concentration of airborne microorganisms after being exposed to the negative ions. Z was determined experimentally by adjusting the ion intensity and the slope of the fitted line is the Z. 

A three-dimensional (3D) model was constructed in ANSYS ICEM and imported into FLUENT to simulate the negative ion distribution as well as the air flow pattern. The detailed geometry of this ventilation duct is shown in Fig. 2 . The dimensions of the ventilation duct were 0.2 m (W) × 0.2 (H) m × 4.5 m (L). The negative ionizer was located 0.6 m from the inlet, with a diameter of 5 mm and a length of 0.04 m. Its mesh is shown in the sub-graph of Fig. 2. 

The specified boundary conditions are summarized in Table 1 . Even though the disinfection tests were conducted at varied inlet speeds, only the air velocity at 3 m/s was simulated in this study. The potential and the negative ion and bacteria concentrations were implemented into FLUENT and treated as user-defined scalars, UDS0, UDS1, and UDS2, respectively. The negative ionizer was modeled as a velocity inlet and it "emitted" negative ions into the duct system at a constant speed of 0.5 m/s. The ionizer generation rate was determined by the equation: I/ e, where I is the total ion current (A) [16] . The emission strength was obtained by experiment. The initial concentration of bacteria from the inlet was set to 1.0 (dimensionless). The airflow field was solved first, followed by the electrical field. The negative ion and bacteria transportation equations were converged when the residuals reached 10 −5 . The transient simulation was conducted with a time step of 0.1 s. The mesh type was hexa-structured and grid-independent tests were performed with: 1,043,260, 1,522,460 and 1,985,420 grid cells, by comparison the distribution of negative ions in the leeward of the ionizer (x = 0.1 m, y = 0.6-4.5 m, z = 0.07 m), the discrepancy for these three types of cell numbers was no more than 5%, thus we selected 1,043,260 grid cells for further calculation to save computational time and resources. The maximum y+ is 54.9, which is sufficient the requirement of y + for standard wall function. Fig. 3 shows the profile of negative ions with measured data along the central line of the ionizer when the inlet velocity was 3.0 m/s. The measured maximum ion concentration was 2.24 × 10 11 ions/m 3 . It was expected that the ion level would decrease dramatically with increasing downstream distance because of the high ion mobility, which would lead to significant loss to the duct wall. The negative ion distribution predicted by the present model agrees well with the experimental results. The discrepancy between the modeling and experiment can be attributed to the limitation of the negative ion counter and misalignment of the ion counter directly facing the negative ionizer. Fig. 4 shows the disinfection efficiency of S. epidermidis and S. marcescens at different inlet velocities. The inactivation of negative ions on bacteria performed better at lower inlet velocities. The highest effectiveness for bacteria removal was 16% for S. epidermidis and 30% for S. marcescens when the inlet velocity was 3.0 m/s. The disinfection efficiency decreased when the inlet velocity increased. For S. epidermidis, the disinfection efficiency gradually decreased to 9.5% and 7.7% when the inlet velocity was 5.0 m/s and 6.0 m/s, respectively. For S. marcescens, the disinfection effectiveness decreased to 17.1% at 4.0 m/s and 6.5 m/s. As the velocity increased, the dose (ion level multiplied by exposure time) received by the bacteria decreased, which reduced the disinfection efficiency. Fig. 5 shows the disinfection efficacy of S. marcescens and S. epidermidis for voltages of 12 V and 6 V. The negative ion intensity at the sampling point for the two voltages was 4.54 × 10 10 ions/m 3 for 12 V and 3.16 × 10 10 ions/m 3 for 6 V. In the case of S. marcescens, the disinfection efficacy decreased from 31.5% to 20.7% with a standard deviation of ± 11%. For S. epidermidis, the disinfection efficacy decreased from 11.9% ( ± 0.3%) to 5.8% ( ± 3.5%). These results were used to determine the susceptibility constant for each microorganism.

The method for calculating the susceptibility constant was illustrated in Section 2.3; it was determined by the relationship between the ion intensity and the inactivation efficacy. By plotting ln(C on /C off ) against N ion , the linear-fitted slope is the susceptibility constant (Eq. (14) ), as shown in Fig. 6 . The constants for S. epidermidis and S. marcescens were 2.723e −11 and 8.676e −11 CFU/ions, respectively.

The bacteria concentrations for both S. epidermidis and S. marcescens were determined when the susceptibility constant was fed back into the source term of the bacteria equation (Eq. (9)), as shown in Fig. 7 . Compared to removal by disinfection, the effect of gravitational settling and wall deposition was only 0.02%, and thus these two effects could be ignored because the selected bacteria were only 1 μm in size. The measured disinfection efficiency depends on the constant susceptibility Z and the number of negative ions. The disinfection efficiency against S. marcescens was higher than that of S. epidermidis. The bacteria concentration was nearly zero downstream very close to the ionizer for two reasons: first, the bacteria distribution at the back of the ionizer was relatively low due to the effect of fluid flow around the cylindrical tube; and second, the largest number of negative ions occurred here, resulting in a distribution of bacteria near zero because the disinfection efficacy was assumed to increase linearly with negative ion concentration (when the velocity is the same). The disinfection efficiency decreased at distances far away from the ionizer because the number of negative ions decreased. The predicted concentration of bacteria (facet average at the sampling cut-plane) was 32.8% and 12.7% for S. epidermidis and S. marcescens, respectively, as compared to the experimental results, as shown in Table 2 .

Reducing energy for air conditioning systems has a significant effect on global energy consumption. The fibrous filtration approach has been used since air conditioning systems were first introduced. It is of great interest to develop a non-filter-based solution for microorganisms. Inactivation of bacteria leads to harmless substances that pose no threat to humans. Air ions could be a potential approach, but such a method has not been studied systematically, even though the effect of negative ions on microorganisms has long been controversially disputed in many research areas [9, 30] . In this study, the distribution of negative ions and their effects on bacteria were numerically and experimentally investigated in ventilation ductwork. Gram-positive S. epidermidis (ATCC 12228) and Gramnegative S. marcescens (ATCC 6911) microorganisms were selected to conduct the disinfection experiment. The disinfection efficiency at different inlet velocities was studied, and it was found to range from 8% to 16% and from 17% to 31% for S. epidermidis and S. marcescens, respectively. The pressure drop ΔP ranged from 1.84 Pa to 8.23 Pa, the ionizer inside the duct had a much lower pressure drop compared with HEPA filters.

In a previous work [11] , the authors investigated mainly the air ion disinfection effect on those bacteria collected on the filter. For airborne inactivation by negative ions in air duct flow in our case, the susceptibility constant for S. marcescens and S. epidermidis was 8.676e −11 CFU/ ions and 2.723e −11 CFU/ions, respectively. The Z value of a bacteria is a major factor in a particular microorganism's vulnerability to disinfection. This parameter must be determined experimentally. This study measured Z for the two bacteria. This parameter is needed to help engineers estimate the number of the ionizers required for the system and the bacteria concentration indoors. In the modeling part, the distribution of negative ions was simulated, and the results agreed well with the experimental data.

Regarding the safety issue, particular attention was paid on the ozone emission. It is a power oxidant and it has severe health impacts on human. Its generation is always an important concern for any mechanism involving high potential discharge. In this study, the measured ozone concentration was 68 ppb at 1.5 m/s. The emission rate was estimated to be 29 mg/h. This low emission rate would lead to indoor concentrations lower than 50 ppb [31] .

The method proposed may thus play a pioneering role in the simulation of removal mechanisms for various bacteria, particularly in the HVAC field. 

Indoor Air Quality in Commercial and Institutional Buildings, Maroon Ebooks

HVAC Systems and Equipment, American Society of Heating, Refrigerating, and Air Conditioning Engineers

Role of ventilation in airborne transmission of infectious agents in the built environment-a multidisciplinary systematic review

Characteristics of bioaerosol profile in office buildings in Hong Kong

Air filters and air cleaners: rostrum by the american academy of allergy, asthma & immunology indoor allergen committee

Removal of submicron aerosol particles and bioaerosols using carbon fiber ionizer assisted fibrous medium filter media

Removal of fine and ultrafine particles from indoor air environments by the unipolar ion emission

Unipolar ion emission enhances respiratory protection against fine and ultrafine particles

One-pass antibacterial efficacy of bipolar air ions against aerosolized Staphylococcus epidermidis in a duct flow

Experimental and numerical study of the performance of upper-room ultraviolet germicidal irradiation with the effective Zvalue of airborne bacteria

Application of air ions for bacterial decolonization in air filters contaminated by aerosolized bacteria

Air ion behavior in ventilated rooms

A note on the possible electrostatic disruption of bacteria

Bactericidal effects of plasma-generated cluster ions

Modelling the air cleaning performance of negative air ionisers in ventilated rooms

Aerosol removal by unipolar ionization in indoor environments

Inactivation of airborne bacteria by cold plasma in air duct flow

Particle dispersion and deposition in ventilated rooms: testing and evaluation of different Eulerian and Lagrangian models

Study on the disinfection efficiency of multiple upperroom ultraviolet germicidal fixtures system on airborne microorganisms

Development of a numerical model to simulate the biological inactivation of airborne microorganisms in the presence of ultraviolet light

Evaluation of cold plasma inactivation efficacy against different airborne bacteria in ventilation duct flow

Aerosol Technology: Properties, Behavior, and Measurement of Airborne Particles

Application of CFD simulation to predicting upper-room UVGI effectiveness

Modelling the performance of upper room ultraviolet germicidal irradiation devices in ventilated rooms: comparison of analytical and CFD methods

Modeling indoor particle deposition from turbulent flow onto smooth surfaces

Modeling particle dispersion and deposition in indoor environments

Modeling particle deposition from fully developed turbulent flow in ventilation duct

Particle deposition in indoor environments: analysis of influencing factors

Application of corona discharge-generated air ions for filtration of aerosolized virus and inactivation of filtered virus

Bactericidal action of positive and negative ions in air

In-duct Air Cleaning Devices: Ozone Emission Rates and Test Methodology (Chapter 1) & 5. Prepared for the California Resources Board and the California Environmental Protection Agency

The work described in this paper was partly supported by a General Research Fund