key: cord-0760125-j839p08t authors: Ballard, David H.; Jammalamadaka, Udayabhanu; Meacham, Kathleen W.; Hoegger, Mark J.; Burke, Broc A.; Morris, Jason A.; Scott, Alexander R.; O'Connor, Zachary; Gan, Connie; Hu, Jesse; Tappa, Karthik; Wahl, Richard L.; Woodard, Pamela K. title: Quantitative fit tested N95 respirator-alternatives generated with CT imaging and 3D printing: a response to potential shortages during the COVID-19 pandemic date: 2020-11-21 journal: Acad Radiol DOI: 10.1016/j.acra.2020.11.005 sha: 627043cfe96330b2c4af4fb5be3b94f9368c3f70 doc_id: 760125 cord_uid: j839p08t RATIONALE AND OBJECTIVE: 3D printing allows innovative solutions for personal protective equipment, particularly in times of crisis. Our goal was to generate an N95-alternative 3D printed respirator that passed the Occupational Safety and Health Administration (OSHA)-certified quantitative fit testing during the COVID-19 pandemic. MATERIALS AND METHODS: 3D printed prototypes for N95 solutions were created based on the design of commercial N95 respirators. CT imaging was performed on an anthropomorphic head phantom wearing a commercially available N95 respirator and these facial contour data was used in mask prototyping. Prototypes were generated using rigid and flexible polymers. According to OSHA standards, prototypes underwent subsequent quantitative respirator fit testing on volunteers who passed fit tests on commercial N95 respirators. RESULTS: A total of 10 prototypes were 3D printed using both rigid (n=5 designs) and flexible materials (n=5 designs), Prototypes generated with rigid printing materials (n=5 designs) did not pass quantitative respirator fit testing. Three of the 5 prototypes with flexible materials failed quantitative fit testing. The final two prototypes designs passed OSHA-certified quantitative fit tests with an overall mean fit factor of 138 (passing is over 100). CONCLUSIONS: Through rapid prototyping, 3D printed N95 alternative masks were designed with topographical facial CT data to create mask facial contour and passed OSHA-certified quantitative respiratory testing when flexible polymer was used. This mask design may provide an alternative to disposable N95 respirators in case of pandemic-related shortages. Furthermore, this approach may allow customization for those that would otherwise fail fit testing on standard commercial respirators. The Coronavirus Infectious Disease 2019 pandemic is caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), which can be spread via virus-containing airborne particles (1) . Healthcare workers are particularly vulnerable to infection given their occupational exposures, including respiratory droplets and aerosol generated by patients infected with SARS-CoV-2, which can remain infectious for hours after becoming airborne (2) . Early in the COVID-19 pandemic, there were PPE shortages, particularly N95 respirators, and concerns that there may be long-term shortages (3) . N95 respirators are certified by the National Institute of Occupational Safety and Health (NIOSH), and their low cost and high functionality have helped them become the most common particulate-filtering facepiece respirator (4) and are certified by the National Institute of Occupational Safety and Health (NIOSH). Filtration depends on a close facial fit that is verified via standardized fit testing (5) . When properly used, at least 95% of airborne particles are filtered when tested against a difficult particle size to filter (approximately 0.3 microns) (hence the "95" in N95), including pathogen-containing particles (5) . Thus, concerns of limited masks during the COVID-19 pandemic (6, 7) prompted an investigation of viable alternatives, including those generated with 3D printing technology. A number of 3D printed N95 alternative designs have been published (8) (9) (10) (11) (12) or are freely available online (13) (14) (15) (16) (17) , standardized fit test performance data to ensure protection from aerosolized particles is lacking (18) . The purpose of this study was to generate a 3D printed N95 respirator alternative that passed an Occupational Safety and Health Administration (OSHA)-certified quantitative fit test. Our institutional review board designated this project as non-human research as no personal or identifying information was collected. CT examinations of commercial N95 respirators were performed to design a novel 3D printed N95 alternative and were tested on healthcare professional volunteers. This study was conducted during the early COVID-19 pandemic period, March 19 to May 25, 2020. Iterative generation of a 3D printed N95 alternative was facilitated by serial rapid prototyping and feedback provided by a multidisciplinary task force. An N95 task force was formed at our institution, a subgroup of a larger initiative (institutional maker task force) to manufacture or secure other forms of personal protective equipment (e.g., face shields, surgical gowns, cleansing wipes, and other items). This task force was generated to address the potential shortage projected during the early COVID-19 pandemic period. At the onset of the study period (March 2020), we were prototyping N95 alternative solutions at the initiative of institutional efforts to address an anticipated shortage of N95s along with surgical masks. Within the N95 alternative task force team, there were over 40 physicians, scientists, engineers, and other experts. This team worked together to form a testing solution to test ad hoc N95 respirators from 3D printed and cloth solutions. Although named an N95 task force, the aim was also to manufacture or secure other mask solutions that would offer some level of filtration and liquid barrier protection. Members of the directed task force were given access to OSHA-certified qualitative and quantitative respiratory fit testing equipment with direct supervision by institutional occupational health personnel. This culminated in the testing and validation of several N95 solutions, including the 3D printing efforts presented in this work. Prototypes, including the ones presented in the current study, were discussed in twice weekly task-force affiliated multidisciplinary videoconference calls. During these meetings, mask designs and results of the respiratory fit testing were discussed To aid in designing 3D printed N95 respirators, CT acquisitions of commercial N95 respirators were acquired both alone and donned on an anthropomorphic head CT phantom (Figure 1) (19) , CT data was processed to match the contours of the scanned mask, these data were imported to Blender v2.81 (Blender Foundation, Amsterdam) to design the N95 respirator. To further aid in 3D printed mask designs, another CT examination was performed with the same protocol with a mid-iteration 3D printed mask both in isolation and fitted on the anthropomorphic head CT phantom. Using data from CT images of the N95 mask and the anthropomorphic head CT phantom, an N95 respirator mask conforming to facial contours was created. Initial prototypes (Figure 2) allowed a filter to be contained between the mask"s skin-facing side and an inner rigid perforated plate. Subsequent prototypes allowed a filter to be contained in an outer circular chamber(s) of the mask (Figures 3 and 4) . Non-3D printed materials required for assembly of all 3D printed mask prototypes included elastic bands, flexible metal for nasal bridge securement, and the filter material (tested using a small section of N95 filter material) (Figure 1) (22) (23) (24) (25) . For masks printed with a Form 2, a Makerbot 5th generation was used to print the inner rigid piece using polylactic acid filaments. The Stratasys J750 printer could print constructs with multiple densities and a second printer was not required for masks printed using this 3D printer. A 7-minute quantitative respiratory fit testing was performed according to OSHA standards (26) on healthcare professional volunteers. The quantitative fit test was performed using a PortaCount Respirator Fit Tester Model 8048 and TSI Model 8026 Particle Generator with TSI FitPro Ultra software (TSI incorporated, Shoreview, Minnesota, USA). A 4 mm metal grommet was punched through each prototype to connect to the PortaCount device"s 4 mm tubing ( Figure 5) . Briefly, the OSHA-certified quantitative respiratory fit test is a supervised examination of an individual wearing an N95 respirator after optimizing it for fit. In the current study, quantitative respirator fit testing was directly supervised and facilitated by our institutional occupational health service, who routinely perform and supervise thousands of annual respirator fit testing for all healthcare workers at our institution. The N95 respirator is connected by tubing to the commercial PortaCount device, which in real-time measures particle concentration around/outside of an individual"s respirator along with the particle concentration leak into the respirator. The ratio of the particles around/outside of an individual"s respirator compared to the concentration inside the respirator is the fit factor, which is the reported real-time measurement of the PortaCount device. A fit factor of >100 is required for an individual to pass the respirator quantitative fit test for an N95 respirator (or half mask or quarter facepiece respirator) A fit factor of 100 means the particle concentration around/outside the respirator is 100 times greater than within. With the device recording real-time dynamic measurements, the quantitative respiratory fit test consists of 8 prompted and standardized exercises where the individual follows the computer prompt. These include normal breathing, deep breathing, two variations of head movement (side-to-side and upand-down), while talking (reading from a prompt), grimace facial expression, bending over, normal breathing. Fit factors are generated for each of these exercises and the overall fit factor for the test is calculated from the number of exercises divided by the inverse values of each individual exercise final mean fit factor. Fit testing was performed on four individuals who passed the OSHA 7-minute standardized fit test for a regular size N95 respirator (n=5) and a small size N95 respirator (n=2). The healthcare professional volunteers gave direct feedback on subjective characteristics, specifically degree of comfort, along with identifying points of fit test failure (e.g., if there were obvious or perceptible air gaps from the mask not being tightly opposed to the individual"s face) and the ease of breathing (scaled from labored, uncomfortable, acceptable, and comparable to normal breathing). 3D printed N95 masks were generated through multiple iterations facilitated through our institutional task force. 25 3D prints of 10 prototype mask designs were tested, with each prototype undergoing direct feedback from the fit testing participants along with a discussion with engineering and occupational health experts. In line with our goal of generating a N95 equivalent, we required use of standard fit testing equipment. Quantitative fit testing instrumentation requires tubing to be in communication with the internal chamber of the mask; this requires generation of hole within the mask. The fit testing was facilitated by a grommet hole punch device (same as used for standard N95s). in initial prototypes, the generation of a hole fractured the mask around the whole punch device ( Figure 5 ). In next iterations, a similar diameter defect was3D printed to simulate the grommet, but this also caused fracture of the material around the mask. A final successful modification was to insert the grommet hole punch device into the filter material rather than the printed component ( Figure 5) . Masks were generated from different rigidity polymers, and in this work, we used both rigid (n=5 designs) and flexible materials (n=5 designs) (Supplementary Table 1) , with a total of 25 total 3D printed masks of the 10 prototypes. None prototype masks that were 3D printed using rigid materials for the proximal facial component (n=5 designs), passed the quantitative respirator fit tests (mean fit factor of 0). The rigid prototypes had volunteer feedback of discomfort and obvious air gaps and were highly uncomfortably with the rigid polymer indenting individual"s skin. An early flexible polymer prototype (Figure 2) passed a qualitative fit test (the prototype first to pass any type of fit testing), but failed a quantitative fit test with a mean fit factor of 15 (passing is 100) (26). Intermittent flexible prototype designs had a mean fit factor of 23 (range 6 to 36). For early and intermittent prototypes, the dimeter of the outer chamber where the filter was situated was 4 cm and ease of breathing was rated as "uncomfortable" to "acceptable". Increasing the outer chamber to 6 cm for the final prototype designs improved the ease of breathing to consistent levels of "acceptable". The two final prototype designs (Figures 3 and 4) printed with flexible polymers (primarily Biocompatible Clear MED610 and Agilus30) passed an OSHA-certified quantitative fit testing with a mean fit factor of 138 (range 108 to 168 [passing is 100]) (26). Additional fit testing data is noted in Supplementary Table 2. The comfort level was noted as similar to commercial N95 respirators. Mean print time for rigid material masks that did not pass respiratory fit testing was 6 hours. Mean print time for early flexible material masks that did not pass quantitative respiratory fit testing, printed with the FormLabs Form 2, was 11.5 hours: the platform for this printer allows for a maximum 1 mask per print. For the final flexible material mask that passed respiratory fit testing, printed with Stratasys J750 3D printer, had an individual mask mean print time of 10.5 hours. The build platform for J750 allows for 10 masks to be printed in 24 hours. The disconnect in mean time between one vs. ten masks is due to the logistics of the build platform of a single 3D printer used for the final prototype. In March 2020, challenges related to airway PPE shortages during the COVID-19 pandemic (27) drove us to generate an N95-equivalent 3D printed respirator that could be used in the hospital setting. The rapid prototyping afforded by 3D printing allowed multiple mask prototypes and iterations, ultimately leading to a 3D printed N95 alternative that passed OSHA-certified quantitative respirator fit tests and was optimized for user experience. Further, given the rapid prototyping and flexibility afforded with 3D augmentation of the design allowed incorporation of multiple filter ports and sizes of the filter fixation sites, to increase surface area for filtration. A survey undertaken in March 2020 revealed that nearly half of all reporting US healthcare facilities were nearly or completely out of N95 respirators (27) . At the time of development, we did not know if our institution or others would have an adequate supply and N95 level protection. Shortages were predicted at our institution for various PPE, including N95 level respiratory protection. Therefore, we created an ad hoc task force centered around the creation of the 3D printed mask in the current study. We aimed to manufacture these masks with the goal of a design that could be rapidly-disseminated, mass-produced, and pass quantitative respiratory fit testing. For the 3D printed mask design in the current study, several designs and materials were considered and we found the greatest comfort and fit test pass rate was with flexible polymers. Initially prototypes were printed with rigid polymers, including polylactic acid and thermoplastic polyurethane. Rigid polymers carry the advantages of low cost and compatibility with most desktop 3D printers, namely using fused deposition modeling (28) . However, masks made with rigid materials were uncomfortable and did not pass the respirator fit testing. On the other hand, masks made with silicone-like consistency polymers passed respirator fit testing and had better user comfort. Although we did not formally measure approximation of mask with skin, fit testing assumes adequate approximation. Rigid materials had obvious air gaps at their facial contours. In this study, we rapidly generated 3D printed masks that were not specifically tailored to the individuals undergoing fit testing -masks were generated from CT images from a anthropomorphic "mannequin" head. Had 3D printed models been generated using imaging of the individuals undergoing testing, we suspect fit testing would have been optimized, although that would have exposed the individual to a finite dose of ionizing radiation. However, radiation exposure could be avoided with other techniques to record facial geometry such as laser scanning or photogrammetry. Along these lines, we also speculate that 3D printing may provide alternatives for respiratory PPE in those that do not pass-fit testing with standard commerciallyavailable N95 respirators due to size or anatomical variation. Many essential healthcare workers fail initial N95 fit testing (29, 30) due to variations in face morphology. Tailored 3D printed masks may overcome these limitations using imaging data contoured specifically to the user. Others have reported using facial scans molding for 3D printed N95 alternatives manufactured with rigid materials (8, 9) , but have not described fit testing results (18) . Facial scanning to allow customization to pass fit testing could have utility in unique situations, but may not be practical as a method used for everyone. Customized 3D-printed masks may have advantages over traditional airway PPE, such as N95 masks. Degesys et al. (31) reported that individuals that passed standard N95 respirator fit testing within the last 1-2 years, experienced failure with both duckbill and dome-shaped masks with extended use; increased failure rate was associated with increased donning/doffing, and total hours used. Maranhao et al. (32) reported higher probability of fit testing failure with commercial disposable N95 respirators when re-used and sterilized after 4 days of continuous use. Further, activities in close approximation to patients, such as cardiopulmonary resuscitation, reduce efficacy of N95 in those that would otherwise pass fit testing (33). The 3D printing community response was unlike anything we have seen with 3D printing rising to a challenge. The digital nature of 3D printing and associated decentralized production allows rapid response in times of crisis. During the early COVID 19, traditional supply chains could not meet the healthcare demands, and in some cases 3D printing was used to fill these needs (12, 34) . Compared to the H1N1 2009 pandemic, now in the COVID-19 pandemic 3D printers are more widely used, cheaper, and integrated into aspects of medicine and rapid prototyping of medical devices. This is in part because in 2009 key 1989 intellectual property for 3D printers" designs expired, which in turn allowed for more 3D printing companies to produce printers, ultimately driving down the cost (35) . In the case of COVID-19, both the scale of the pandemic and printer availability drive this response, which manifested in N95 mask alternatives, face shield production, nasal swabs, ventilator part supplements, and mask extenders (8-12, 34, 36-40) . As the COVID-19 pandemic progressed, traditional N95 supply methods were able to meet demands at our institution. Nonetheless, these digital blueprints can be used in future times of need. The National Institutes of Health has hosted many 3D printed PPE designs on the NIH 3D Printing Exchange (13) . There are several limitations with 3D printed respirators. An advantage of commercial N95 respirators is that they have a relatively large area of air exchange, which decreases air resistance and, therefore, potentially work of breathing. The surface area of filter material required to maintain N95 filtration will be dependent upon the filter material used. In later iterations we increased the surface area two double that of initial prototypes. Thus, the overall effectiveness of the mask in the healthcare setting may vary. We offer a design that passed standardized OSHAcertified quantitative fit testing and strongly recommend centers perform such testing on any 3D printed prototype. The fit testing was successful on a small number of volunteers and it is unknown if fit testing would be successful over a wide range of individuals. The mask that was generated was based on the contours of a mannequin head, we suspect that customized masks generated from contour maps of individuals would have even better fit tests results and comfort. With the implementations of institutional re-use of disposable N95s, limiting on-site personnel, and with our institutional burden of COVID-positive and suspected patients, we did not reach a point where the clinical use of this mask in a widespread manner was required. However, 3D printing resources at our institution were prepared and worked towards the goal of rapidly producing a design that passed OSHA-certified quantitative fit testing. In the case that individuals were to wear 3D printed masks that would approximate the skin, confirmation of biocompatibility is recommended according to the FDA document on technical considerations for additive manufactured devices (41) . We suspect rates would be low with the inert compounds and the polymers used in this study do have safety and chemical data sheets available from the manufacturer (22) (23) (24) (25) . In the event that there are adverse skin reactions, different polymers could be used. In this work, we do not objectively report comparisons with other available designs, although we have printed a number of these (5 designs) and none passed a fit test, primarily due to rigid materials, and it is likely that soft polymers substantially aid in achieving adequate fit along the contours of variable facial anatomy. A limitation of this work is that it was not compared to published (8) (9) (10) (11) (12) or freely available N95 alternatives (13) (14) (15) (16) (17) : however, at the early onset of this work, there was only one freely available 3D printed N95 alternative. No comparison group in this work was partly driven by this 3D printed mask development was a potential need with anticipated N95 respirator shortages, therefore, it was expedited to achieve a model that passed quantitative respiratory fit testing. The 10 masks per 24 hours mean print time for the 3D printer used in the final prototype"s production may not be favorable for a mass production standpoint. In considering this and if these masks would have been required for clinical use, the task force in the current study had industry collaboration to make a mold of the mask design for higher volume production. In conclusion, we developed an ad hoc 3D printed N95 mask solution during the COVID-19 early pandemic period. Although several designs for 3D printed N95 alternatives have been published (8) (9) (10) (11) (12) or freely available (13) (14) (15) (16) (17) in response to and during the COVID-19 pandemic, the vast majority do not pair the design with respiratory fit testing data (18) . The current study provides a 3D printed N95 respirator alternative design that passed quantitative respirator fit testing. In different iterations of the mask prototypes in this study, flexible polymers provided a better fit of 3D printed masks modeled as N95 respirator alternatives and provided better comfort compared to rigid materials. From our available resources and data, rigid 3D printed N95 respirator alternatives were less expensive and printed faster compared to flexible N95 alternative; however, rigid N95 3D printed alternatives did not pass respiratory fit testing according to OSHA standards. A highlight of this study was that it used rapid prototyping and iteration to generate a potentially viable N95 alternative. Fortunately, we never reached a point where we were required to use the masks we generated, but we suspect this process of rapid prototype/iteration facilitated by 3D printing is translatable to future urgent needs in healthcare. Transmission of COVID-19 virus by droplets and aerosols: A critical review on the unresolved dichotomy Aerosol and Surface Stability of SARS-CoV-2 as Compared with SARS-CoV-1 Covid-19 and the N95 respirator shortage: Closing the gap NIOSH-Approved N95 Particulate Filtering Facepiece Respirators. CDC Website. Available at Effect of fit testing on the protection offered by n95 filtering facepiece respirators against fine particles in a laboratory setting Strategies for Optimizing the Supply of N95 Respirators Critical Supply Shortages -The Need for Ventilators and Personal Protective Equipment during the Covid-19 Pandemic Custom-made 3D-printed face masks in case of pandemic crisis situations with a lack of commercially available FFP2/3 masks Use of free CAD software for 3D printing individualized face masks based on face scans Ten Days to Implementation of 3D-Printed Masks for a Level-I Orthopaedic Trauma Practice During the COVID-19 Pandemic A customized 3D printed N95 respirator analogue to face crisis capacity scenarios in pandemics such as the COVID-19 and to support surgical personnel during PPE shortages COVID-19 and the role of 3D printing in medicine Make the Masks Website Project (N95 Alternative Filter) Boston Children"s Hospital Website Safety concerns for facial topography customized 3D-printed N95 filtering face-piece respirator produced for the COVID-19 pandemic: initial step is respiratory fit testing 3D Slicer as an image computing platform for the Quantitative Imaging Network Elastic Resin Safety Data Sheet. FormLabs Website. Available at Flexible Resin Safety Data Sheet. FormLabs Website. Available at MED610™ Safety Data Sheet. Stratasys Website. Available at Protecting Healthcare Workers During the COVID-19 Pandemic: A Survey of Infection Preventionists. Association for Professionals in Infection Control and Epidemiology Logistics of Three-dimensional Printing: Primer for Radiologists The Effect on Fit of Multiple Consecutive Donning and Doffing of N95 Filtering Facepiece Respirators Evaluation of the user seal check on gross leakage detection of 3 different designs of N95 filtering facepiece respirators Correlation Between N95 Extended Use and Reuse and Fit Failure in an Emergency Department Probability of fit failure with reuse of N95 mask respirators N95 filtering facepiece respirators do not reliably afford respiratory protection during chest compression: A simulation study 3D Printed Face Shields: A Community Response to the COVID-19 Global Pandemic Medical 3D Printing Cost-Savings in Orthopedic and Maxillofacial Surgery: Cost Analysis of Operating Room Time Saved with 3D Printed Anatomic Models and Surgical Guides In-House Three-Dimensional Printing Workflow for Face Shield During COVID-19 Pandemic 3D Printed Alternative to the Standard Synthetic Flocked Nasopharyngeal Swabs Used for COVID-19 testing Ventilated Upper Airway Endoscopic Endonasal Procedure Mask: Surgical Safety in the COVID-19 Era Increasing ventilator surge capacity in COVID 19 pandemic: design, manufacture and in vitro-in vivo testing in anaesthetized healthy pigs of a rapid prototyped mechanical ventilator 3D printed mask extenders as a supplement to isolation masks to relieve posterior auricular discomfort: an innovative 3D printing response to the COVID-19 pandemic Additive-Manufactured-Medical-Devices---Guidance-for-Industry-and-Food-and-Drug-Administration-Staff.pdf