key: cord-0760004-p4hry0mr
authors: Teles, Fernando; Fonseca, Luís
title: Nucleic-Acid Testing, New Platforms and Nanotechnology for Point-of-Decision Diagnosis of Animal Pathogens
date: 2014-08-11
journal: Veterinary Infection Biology: Molecular Diagnostics and High-Throughput Strategies
DOI: 10.1007/978-1-4939-2004-4_20
sha: 8b9bf8ae4682528475db8cca89b4287c2b58f42a
doc_id: 760004
cord_uid: p4hry0mr

Accurate disease diagnosis in animals is crucial for animal well-being but also for preventing zoonosis transmission to humans. In particular, livestock diseases may constitute severe threats to humans due to the particularly high physical contact and exposure and, also, be the cause of important economic losses, even in non-endemic countries, where they often arise in the form of rapid and devastating epidemics. Rapid diagnostic tests have been used for a long time in field situations, particularly during outbreaks. However, they mostly rely on serological approaches, which may confirm the exposure to a particular pathogen but may be inappropriate for point-of-decision (point-of-care) settings when emergency responses supported on early and accurate diagnosis are required. Moreover, they often exhibit modest sensitivity and hence significantly depend on later result confirmation in central or reference laboratories. The impressive advances observed in recent years in materials sciences and in nanotechnology, as well as in nucleic-acid synthesis and engineering, have led to an outburst of new in-the-bench and prototype tests for nucleic-acid testing towards point-of-care diagnosis of genetic and infectious diseases. Manufacturing, commercial, regulatory, and technical nature issues for field applicability more likely have hindered their wider entrance into veterinary medicine and practice than have fundamental science gaps. This chapter begins by outlining the current situation, requirements, difficulties, and perspectives of point-of-care tests for diagnosing diseases of veterinary interest. Nucleic-acid testing, particularly for the point of care, is addressed subsequently. A range of valuable signal transduction mechanisms commonly employed in proof-of-concept schemes and techniques born on the analytical chemistry laboratories are also described. As the essential core of this chapter, sections dedicated to the principles and applications of microfluidics, lab-on-a-chip, and nanotechnology for the development of point-of-care tests are presented. Microdevices already applied or under development for application in field diagnosis of animal diseases are reviewed.

As in human medicine, disease diagnosis in veterinary medicine and practice is important for several reasons, including the issues of animal health and welfare, public health (especially in the case of zoonotic agents affecting pets or animals for human consumption), and economy (mainly related to the rules and barriers for the international trade of animals and animal products). In the veterinary fi eld, it is important to consider fauna species other than cattle and farming animals (mainly large terrestrial livestock animals and fi shes for aquaculture as well), like pets, captive (e.g., zoo, circus, and aquariums), and wild animals. All of these constitute underestimated sources of many human infectious diseases, especially of

viral origin. Animal or human contamination with a veterinaryrelevant pathogen may occur through infected animals (live or dead) and infected animal products (e.g., bush meat, unpasteurized milk) or, to a lesser extent, through direct contact with the pathogen itself. In developing countries and regions, the impact of livestock diseases and outbreaks goes far beyond animal welfare and food safety. Too often, farm animals are also the only way of human and cargo transportation and also of income, as feedstock, as a source of manure and draft power, and as raw material for other industries (e.g., leather, shoes, and clothing) [ 1 ] . The advent of human immunodefi ciency virus (HIV)/acquired immunodefi ciency syndrome (AIDS) and other human immune depressing conditions has been a relatively neglected factor of enhanced susceptibility of humans to animal diseases, especially with respect to pets. Immune-depressed individuals or other vulnerable groups, such as children or the elderly, may even become susceptible to subtypes of zoonotic microorganisms that are usually harmless for healthy humans [ 2 ] . Interaction between domestic and wild animals may also provide an important via for indirect human contamination [ 3 ] . A particularly important group of zoonotic agents is that of enteric pathogens that are transmitted to and between humans and animals through the oral-fecal route, with subsequent dissemination to wastewater effl uents. Outbreaks may occur upon contamination of surface waters and groundwater used for recreational and irrigation purposes and insuffi cient microbial removal of drinking water and/or of treated wastewaters, since many of these enteric pathogens are resilient to classical treatment and disinfection procedures [ 4 ] . They often contaminate water supplies in very small concentrations, hence hindering fi nal disinfection and complicating detection as well [ 5 ] . Screening of enteric zoonotic agents has been proposed for pets cohabiting with immune-susceptible humans [ 6 ] . Very often, the presence of enteric viruses is detected indirectly, through bacterial indicators of fecal contamination, namely, coliforms and enterococci [ 5 ] . On the other hand, emerging "wild-type" zoonosis have been transmitted from animals to humans (e.g., SARS and West Nile virus) or after specifi c mutations that facilitate the "species jump" (e.g., HIV and H5N1 or H1N1 infl uenza) [ 7 ] . Concerning bioterrorism issues and depending on the nature of the infectious pathogen, the detection of potential zoonotic agents in animals should alert for an intentional release act [ 8 ] . A successful anti-bioterrorism strategy must not only account for the detection of the known pathogen but also of genetically modifi ed forms. However, only a few potential veterinary pathogens fulfi ll the criteria for being considered effective bioterrorist agents. The group is composed by the viral agents of rinderpest, classical swine fever, African swine fever, avian infl uenza, Newcastle disease, Rift Valley fever, and foot-andmouth disease (FMD) [ 1 ] . Among them, FMD and avian infl uenza are especially important for their high prevalence in the world, zoonotic potential, and ramping spread. FMD is generally considered the most contagious viral disease in animals. Occasional occurrences in non-endemic regions are usually diffi cult and expensive to control [ 9 ] . Avian infl uenza is a viral disease with pandemic potential; pigs can act as intermediate hosts of infl uenza viruses between birds and humans. Bidirectional transmission of these viruses between humans and pigs is documented [ 7 ] .

The diagnosis of air-borne diseases is challenging, with implications in disease control, especially in the case of outbreaks, and in individual case management. For these diseases, timely adoption of quarantine measures and massive antimicrobial therapy administration may be suffi cient to contain an emerging outbreak, as long as the fi rst cases are spotted in a short time. However, this may be impracticable in developing countries and regions, where effective routine surveillance fl aws. Thus, a successful containment strategy must include rapid diagnosis through inexpensive and easy-to-use portable devices for in-the-fi eld use [ 10 ] . As an example, it has been proposed that, within 6 h of the reporting of a suspicious FMD case, defi nitive detection should be made upon sample transportation to a national or regional laboratory, or else on the farm itself, and that, within 24 h of reporting, defi nitive identifi cation of the infecting strain/subtype should be accomplished, immediately followed by vaccine production (from stored antigens) and distribution [ 1 ] .

Following the trend of human medicine, the diagnosis of animal diseases has also undergone progressive decentralization, from central (reference) laboratories to in-the-fi eld bioanalytical instrumentation, very often in resource-depleted regions and settings, even outside laboratory infrastructures. Essentially, this has been done through adaptation of conventional analytical methods and instrumentation to portable and automated devices, able to be handled by laboratory unskilled personnel (viz., veterinarian practitioners and farmers). Several nomenclatures have been given to these tests. They include the names "fi eld tests", "rapid tests", "biosensors", and "point-of-care (POC) tests"; this last term will be predominantly used throughout this chapter. Improved diagnostic tests are necessary for asymptomatic diseases, for diseases with misleading symptoms, for diseases requiring different treatments, or for diseases that, by their complex or costly treatment, require previous case confi rmation. By contrast, these tests will likely have little or no impact for diseases which are easily recognized by their clinical symptoms and for which a syndromic treatment/approach is recommended. There is thus no clinical need to identify the causal agent. However, surveillance and control measures must be maintained for these diseases in order to deal with the risk of major epidemics [ 11 ] . It is among livestock animals that

disease epidemic outbreaks are more likely to occur, and with higher magnitude, given the physical proximity of many animals under intensive husbandry, the probability of pathogens to contaminate neighboring farms, and the relatively poor biosecurity conditions of most farms, but also in the case of subclinical diseases. As time is crucial when managing the early stages of infectious disease, an immediate preliminary positive result obtained by a POC test strongly argues in favor of precautionary and preventive measures in affected farms and surroundings in order to avoid further transmission, until a defi nite and more accurate result can be obtained in a reference laboratory [ 12 ] . Ideally, POC tests should go towards increased sensitivity, not only for early case identifi cation but also for disease surveillance and epidemiological purposes, as infected animals may suffer and constitute infected reservoirs for disease spreading [ 11 ] . During the 2001 FMD outbreak in the United Kingdom, most of the livestock in infected and neighboring farms was targeted for culling during the fi rst 24-48 h, based solely on clinical signs, which may be considerably doubtful, especially in sheep, the main species affected [ 13 ] . The time span between animal infection and the onset of clinical symptoms, and hence infection awareness, can take months, usually through rapid and silent spreading within and between herds, which might need to be destroyed [ 14 ] . However, indoor controlled studies with experimental infection of cattle with FMD virus (FMDV) showed a smaller-than-expected transmission fraction during the overlapping period between the incubation and the infectious period, suggesting that the importance of common preventive measures taken at endangered farms (viz., preemptive culling of cattle, often with severe economic downturn) has been overestimated [ 15 ] . For most viral diseases, since the onset of detectable viremia usually occurs at least 1 day before the onset of infection and/or presentation of clinical signs, efforts should be devoted to the development of new diagnosis methodologies and tools at preclinical stages. Historically, public funds have been used to compensate farmers for massive slaughtering of suspected diseased animals, but it has been argued that this may have generated permissive behaviors and disinterest from livestock industries and owners about transboundary control of cattle diseases [ 1 ] . In theory, POC tests are advantageous over laboratory-based tests if they can be used to detect infected animals before they become infectious, especially if this time window is short, as in the case of FMD. This advantage would apply if the time between collection of samples and receipt of results in the laboratory is, at least, 24 h. In the medium term, POC tests for cattle diseases will likely play an increasing role in the screening and triage of biological samples collected on the farm, as a primary support for decision-making during disease outbreaks [ 16 ] , under a challenging context of permissive biological containment.

In veterinary medicine, POC tests have been largely used, for some decades, for the screening of physiological metabolites in blood and urine. Pathogen detection is a newer application, mainly driven by the increasing number of emerging outbreaks, including those with public health importance. Among these is, for instance, the potentially pandemic H5N1 avian infl uenza, as well as infl uenza viruses of putative porcine origin, as the human pandemic strain of 2009 [ 12 ] . POC tests have also been developed for important diseases of aquatic animals, using similar technologies to those used for terrestrial animals [ 17 ] . The most common layouts of commercially available devices rely on antigen detection in biological samples through affi nity binding reactions with immobilized specifi c antibody probes. Nevertheless, despite the requirement for essentially the same performance features, regulatory approval and introduction of these devices into the market are understandably easier in the veterinary than in the clinical practice [ 18 ] .

Disease sub-notifi cation remains a major problem for veterinarian health authorities; despite notifi able diseases are of obligatory reporting, too often farmers (and even veterinarians and diagnostic laboratories) ignore or delay the notifi cation process owing to unawareness, minimization, or perceived lack of consequences, which may be aggravated when economic losses are anticipated. It is expected this scenario to worsen as POC tests become more readily available for utilization by farmers, especially in cases of delayed or misleading diagnosis based upon the clinical signs, as a result of disease underestimation or confusion with the signs of non-notifi able endemic diseases [ 12 ] . Of course, the interpretation of clinical signs itself and subsequent decision-making processes are compromised by the fact of farmers being unskilled personnel in health and veterinary medicine issues. Reducing the risk of nonreporting depends on tight cooperation and trust between veterinary authorities and livestock farmers and dealers [ 19 ] . In the livestock business, especially for important livestock diseases (e.g., classical swine fever), the risk of announcing a false-positive result is particularly worrisome, as it carries detrimental consequences in trade and export. Sanitary requisites on imported livestock for human feeding are very demanding and restrictive in most countries, leading to severe economic losses in cases of insuffi cient or inaccurate pathogen testing. Therefore, individual animal testing may be one of the main drivers for commercial development of POC tests, because a preliminary positive result with a POC test may prevent further and more expensive testing, while holding the herd being ineligible for export as well [ 12 ] . Some animal diseases are particularly contagious and able to spread rapidly. Many of them are considered transboundary diseases, meaning that their detection turns into the prohibition of livestock export and thus in economic losses. The combination of permanent surveillance

programs with improved techniques for rapid detection of emerging pathogen subtypes for effi cient control of transboundary diseases has been claimed [ 20 ] . Unambiguous identifi cation of circulating pathogen subtypes (viz., genotypes and/or serotypes) is frequently a relevant epidemiological feature for the success of disease control programs. For low-prevalence diseases, the proportion of falsepositive results is usually higher than for more prevalent ones. In addition, many of the current POC tests are less sensitive and specifi c than laboratory-based methods. Altogether, this means that, in order to achieve a desired level of performance and confi dence in the results, sampling a large number of animals is usually required for POC-based testing of low-prevalent diseases [ 12 ] . In pets, the prevalence of many pathogens, particularly of zoonotic parasites, has been probably underestimated as a consequence, among other reasons, of using inadequate and inaccurate diagnostic tests and procedures, including limitations in sample collection and processing, which may directly result in false-negative results [ 21 , 22 ] and, as such, putting the animals themselves and their owners at greater risk than currently assumed [ 3 ] .

Intellectual property constraints frequently hamper the passage of these new devices from the proof of principle to the prototype and even commercialization levels. Another bottleneck is the high cost for fi nal development of such devices, the reason why partnerships between research laboratories and biotechnological companies are usually established with such purpose. In this case, of course, the economic leitmotiv is much higher for high-impact diseases, especially those for which control of outbreaks is diffi cult and expensive. However, even for such diseases (e.g., FMD), the only sporadic and unpredictable character of outbreaks might disincentive investments in individual testing; high demand usually only occurs by the occasion of an outbreak or suspected outbreak. Only a few tests for economically important livestock diseases have been developed and commercialized in developed countries, due to the limited market resulting from only infrequent diseases [ 12 ] . It seems that the most promising commercial segment for POC devices for veterinary pathogens concerns multiplexed platforms for a wide range of endemic and non-endemic pathogens [ 16 ] , taking advantage of the relative simplicity and low cost of incorporating several additional targets in a multiplexed test. Indeed, veterinary health services eagerly lack rapid and simple diagnostic devices designed for in-the-fi eld simultaneous detection, in a single sample, of a broader range of common pathogens [ 8 ] , thus enabling the rapid gathering of fi eld information on individual animals or whole herds disease status. Currently, simultaneous identifi cation and eventual subtyping of many pathogens in a single test run is a province of central or reference laboratories and only available if the demanding entity (e.g., person, laboratory, or agency) is able to afford to pay for such expensive testing. POC tests have been also used for fi eld differentiation between vaccine and fi eld strains, especially in endemic regions where vaccination is permitted [ 12 ] . Suitable application of such differential testing at slaughtering settings to confi rm prior livestock vaccination has been argued [ 1 ] .

The ultimate goal of the use of POC portable devices by unskilled and unsupervised practitioners will likely pose enormous challenges for the overall bioanalytical process, from sample acquisition to post-analytical data storage, interpretation, and management. Bearing in mind that most of these devices are to be commonly used in remote and low-resource regions, uncontrolled and irregular reporting of results, in addition to test biosafety, especially when dealing with zoonotic agents, are major issues [ 23 ] . For these reasons, a balanced merging between in-the-fi eld testing with remote data analysis and interpretation by competent clinical staff may be desirable. In this regard, telemedicine is an attractive system for healthcare improvement in developing countries, for allowing unskilled persons to provide useful healthcare in remote settings. This can be carried out by using miniaturized analytical devices with integrated hardware for image acquisition and software for storage of results. These results can be downloaded to hard copies or directly transferred online for a remote healthcare central unit for processing and interpretation by expert personal. Processed results can afterwards be returned to the tester, almost in real time [ 24 ] . Remote data from POC systems can still be incorporated in national disease surveillance and diagnostic systems, as the Threat Agent Detection and Response (TADR), developed under the Biological Threat Reduction Program (BTRP) of the US Defense Department's Defense Threat Reduction Agency. This system uses real-time polymerase-chain reaction (rPCR) for detection of pathogens. Another surveillance system, the Electronic Infectious Disease Surveillance System (EIDSS), contains a subsystem to report suspicious disease outbreaks in real time. The EIDSS is able to locate disease outbreaks through a geographic positioning device. This system aims to encompassing all available public and animal disease surveillance information. The EIDSS is able to report laboratory results from rPCR up to a few hours, depending on the distance. These systems will eventually enable a shift of paradigm in remote analysis, allowing world reference laboratories to simply handle and manage diagnostic information from pathogens and hosts based on biological samples remotely collected and analyzed, with subsequent reporting of results to the countries and regions of origin [ 1 ] .

A full evaluation program of POC tests must include performance evaluation (validation), quality assessment (control and assurance), and standardization [ 25 ] . The performance of POC tests is highly dependent on the local conditions for their use,

on the epidemiology of the pathogen, and on the biology of the host [ 26 ] . Thus, the evaluation of such tests sets the particular ranges of in-the-fi eld conditions in which they can be used [ 27 ] , ideally under multicenter evaluation. Quality control assures correct functioning of the devices with prolonged use; usually, randomly selected units from a given production batch are compared to infer reproducibility. The quality assurance step demonstrates the readiness of the tests to be introduced into the routine diagnostic practice. Standardization is needed in POC diagnostics for veterinary applications, as well as new rules to compare results obtained from the two different methodologies-the POC and the laboratory-based method, respectively-which implicates in the fi nal (accepted) diagnostic result [ 23 , 28 ] . Proper validation and standardization of many POC tests frequently lack, in part because these often correspond to in-house rather than to well-standardized assays and techniques. It is thus important that national or reference healthcare entities establish quality assurance programs that guarantee the production of reference materials and protocols for effective quality control of rapid diagnostic tests [ 29 ] . For the clinics, a set of guidelines for standardization of POC blood-based tests has already been established [ 30 ] . Hopefully, in the future, this will also be useful to inspire standardization procedures in new diagnostics for veterinary medicine and practice.

POC tests hold great promise to shift the paradigm of veterinary diagnostics, particularly for fi eld situations, and in cases in which the biological sample is easy to collect and process. However, its advantageous use presumes the availability of suffi cient manpower to survey enough animals on high-risk premises, which remains a burdensome challenge. The decision of whether using them or not to manage animal infectious diseases depends on biological and epidemiological factors, on the specifi c circumstances in which clinical signs arise, on cost-benefi t issues (taking into account the costs for deployment, including equipment and reagent storage), and on the relative performance compared to diagnostic tests in reference laboratories. The possibility of sending suspect samples to a central laboratory within 24-48 h has probably discouraged the use of POC tests in some past situations in Western countries, e.g., under medical suspicion of highly pathogenic avian infl uenza (HPAI); from another point of view, this strengthens the idea of a promising use of these tests in remote regions, far away from laboratory settings. Once POC tests have equivalent analytical sensitivity and specifi city to laboratory-based tests, it may be foreseen, on the basis of a POC test alone, to take actions beyond simple restriction/quarantine on suspect premises [ 12 ] . Transboundary livestock diseases are probably among the major concerns in veterinary medicine. It has been proposed that an effi cient governmental control strategy of these diseases should include legislation enforcing, namely, (a) disease screening in people, conveyances, and goods arriving from other countries, in a reasonable extent, according to previously defi ned performance benchmarks, including possible use of robotic automated devices; (b) higher extent of screening for people, conveyances, and goods arriving from endemic countries, even reaching exhaustive screening when such countries are recognized as not making acceptable progresses in disease control; and (c) the need to develop tests to certifi cate animal product's region or country of origin, at the point of importation [ 1 ] . These points certainly constitute an immense and valuable fountainhead of opportunities for commercial attraction-driven development of new POC devices in the veterinary fi eld.

Early disease diagnosis not only prevents or minimizes potential animal suffering but also the risk for infection transmission among susceptible hosts [ 31 ] . In contrast, delayed diagnosis carries an increased risk for severe symptoms and complications, ultimately leading to longer suffering, increased toxicity due to accumulated pathogen load and/or virulence effects, and a higher risk for acquisition of drug resistance [ 12 ] . Antibody-based detection requires a suffi cient level of antibodies to be produced for successful detection, which usually happens only some days after exposure to the pathogen. In this regard, specifi c detection of pathogen nucleic acids in biological samples by PCR-based methods may be more suitable, since the pathogen genomic material is present in the host from the very beginning of infection and even very little amounts are detectable before the onset of immune response markers or clinical or veterinary signs. Moreover, methods based in nucleicacid detection are able to detect both live and dead pathogens, an advantage for disease diagnosis [ 1 ] , especially when time is crucial for disease containment and control. In conventional methods (e.g., cell culturing and serology), pathogen detection strongly depends on the sample quality [ 13 ] , leading more easily to falsenegative or irreproducible results.

Deoxyribonucleic acid (DNA) is a particularly suitable material for biosensing owing to unique characteristics, including the ability for highly specifi c and mutual recognition between a short immobilized oligonucleotide (probe) and a longer-sized genome and high physicochemical stability. Unlike enzymes and antibodies, DNA forms biological recognition layers easily synthesizable and readily reusable after thermal heating [ 24 ] . DNA is also prone to very specifi c manipulation and processing precision by ligases, nucleases, and other enzymes [ 32 ] and is the most easily copyable biomolecule, through PCR and similar techniques

of amplifi cation, which is also an enormous advantage for the development of portable and miniaturized diagnostic devices. In addition, DNA micro-and nanoarrays are more suitable than protein counterparts for direct synthesis onto a chip surface, without the need to produce and purify the ligands [ 33 ] . Most of these features of DNA are also extensive to ribonucleic acid (RNA). Indeed, nucleic-acid (molecular biology) testing comprises genetic analysis (DNA level) and functional genomics (including mRNA, non-coding RNA, and microRNA). In particular, functional genomics dedicates to the identifi cation and analysis of specifi c RNA expression patterns (profi les) associated with particular experimental or clinical conditions. DNA (and RNA) microarrays and quantitative PCR have been the most common techniques used with this purpose [ 34 ] . DNA microarrays (DNA chips) are usually produced in the form of highly dense arrays printed on a silicon or glass chip, coated with different probes for simultaneous detection of multiple DNA-target sequences [ 35 ] . Current microarrays can detect in the order of 10 4 nucleic-acid sequences on a single chip [ 1 ] . The Virochip is particularly well succeeded in this regard; it is a panviral DNA microarray platform, able to detect known viruses and new viruses related to known viral families, in a single assay. Its high robustness has been confi rmed with viruses of high genetic variability, as the swine virus. This platform is especially useful for detecting viruses for which there are no available reverse transcription-PCR (RT-PCR) assays [ 7 ] . Nevertheless, microarrays do not seem promising for the POC use, being too expensive, complex, and bulky [ 24 ] . Another peculiarity of DNAbased detection is the superior ability to differentiate strains from the same organism, especially when isolated from different geographical locations. This is useful not only for pathogen identifi cation but also for epidemiological studies. As an example, the signifi cant differences among the nucleic-acid sequences of the different serotypes of FMDV (as in other viruses) and the likelihood for the occurrence of typing errors during viral RNA replication demonstrate how the virus can rapidly evolve in nature [ 36 ] , which constitutes an enormous challenge for successful viral identifi cation. In infl uenza viruses, genetic reassortment is able to generate novel subtypes whose cell surface antigens might no longer be recognized by preexisting antibodies (antigenic drift) [ 37 ] . The potential for pandemics caused by novel highly pathogenic subtypes strongly stresses the need for specifi c subtype identifi cation through nucleic-acid testing. Of course, the drifting in infl uenza viruses, responsible for the sudden onset of dominant subtypes during a yearly season, requires not only rapid development and validation of suitable molecular probes for nucleic-acid tests but also the unobstructed use of such tests. Unraveling the pathogen subtypes circulating in a given region may assist in designing tailored vaccines and disease containment strategies, as well as tracking outbreaks' sources [ 38 ] .

Most of the current POC tests for human and animal medicine still rely on antigen/antibody bioaffi nity reactions, but they are usually handicapped by relatively small sensitivity. Thus, there is a trend for shifting towards more sensitive nucleic-acid detection, usually based on DNA/DNA hybridization schemes. A major challenge for detection of pathogen nucleic acids in host body fl uids, apart their scarcity compared to antigenic proteins, is the confi nement inside pathogen cells, surrounded by hard biomembranes and cell walls. Consequently, the nucleic-acid levels present in host fl uids may be too low for successful diagnosis without prior target amplifi cation by PCR-based techniques. For blood infections in humans, the amount of human genomic DNA can be 10 14 times higher than that of pathogen DNA [ 39 ] , an important challenge in terms of sensitivity and selectivity. For POC testing, this constitutes a challenge for the miniaturization of the blood sample preparation step, especially in the case of gram-positive bacteria, whose cell walls are thicker and more rigid than those of gram-negative bacteria. The majority of available POC systems for clinical and veterinary applications require off-device sample preparation (including microorganism concentration and nucleic-acid extraction). This is a traditionally cumbersome and time-consuming step, especially for in-the-fi eld testing, but newer processes, including fi lter paper capture of nucleic acids and automated extraction procedures and kits, have been developed to simplify such task [ 40 ] . In parallel with POC device development, considerable efforts have been spent in the simplifi cation and robustness of sample preparation, in order to minimize manual handling, thus reducing cross-contamination and the effects from potentially interfering substances present during the nucleic-acid amplifi cation assay. Of note are the technical diffi culties inherent to the analysis of matrices such as feces, semen, and decomposing tissue or the detection of Mycobacterium tuberculosis from saliva [ 12 ] . For these cases, it is necessary to incorporate, in POC devices, systems that are able to suppress such interfering substances and that reduce handling prior to the nucleic-acid amplifi cation step. PCR has been, by far, the most widely employed technique for nucleic-acid amplifi cation in laboratory analysis but also in POC tests. Many similar techniques have been originated from the basic PCR principles, including nucleic-acid sequence-based amplifi cation (NASBA), targeted for direct RNA amplifi cation, thus precluding the need for a previous reverse-transcription step. The development of this panoply of techniques for pathogen detection has been possible due to the increasing availability of whole genomic sequences; a remarkable case in veterinary science is the current possibility of rapidly distinguishing severe acute respiratory

syndrome (SARS) from other circulating coronaviruses [ 41 ] . Nevertheless, PCR is prone to false-positive results, as a result of unwanted amplifi cation of contaminant nucleic acids. Proper quality management of these issues requires using adequate controls for each stage of the testing process [ 12 ] . For RNA analysis through RT-PCR, storing biological samples at very low temperatures is crucial, owing to the high liability of RNA genomes. Innovative lyophilized reagents with enhanced sensitivities have signifi cantly improved the operational conditions for POC disease diagnosis [ 42 ] . Moreover, the need for improved stability of RNA used as an internal positive control, especially for real-time RT-PCR assays, has led to the search for new RNA sources. Another approach for improving RNA assays is the use of minor groove-binding probes which, by being short sized, are suitable for multiplexing and for targeting sequences of highly variable genomes [ 20 ] . Nevertheless, PCR-based techniques remain challenging for POC pathogen diagnosis in many endemic regions of the world. Even in human medicine, however, RT-PCR, for instance, is only used for clinically important specimens, due to the complexity and time demanding of this technique [ 43 ] . Linear-after-the-exponential PCR (LATE-PCR) is another PCR-based technique for detection of RNA. Probably its most known application is in FMDV subtyping, to tackle the diffi culty of targeting all fi eld strains with novel sequence mutations, even those in target sequences for which degenerate primers are being used [ 44 ] . The amplifi cation process can begin with as few as a single DNA molecule and abundantly generates amplifi ed product over a broad temperature range. The technique employs primers that hybridize to conserved genomic regions and a mismatch-tolerant probe able to target different variable sequences, depending on the temperature. Thus, the technique is especially convenient for detection of RNA viruses [ 36 ] .

Among the vast diversity of available nucleic-acid amplifi cation schemes and devices, both at the proof-of-concept and commercial levels, the technique of loop-mediated isothermal amplifi cation (LAMP), already widely used in laboratory analysis, seems quite promising for application in POC systems for pathogen detection and identifi cation. In remote PCR-based nucleic-acid testing, power supply is a keystone for device operation, although the use of rechargeable batteries is expected to circumvent this problem, by avoiding the need for an external power source [ 42 ] . Advantageously, LAMP does not require thermal cycling for the amplifi cation, rather making use of a simpler power source compared to a PCR thermocycler. Such operation at constant and low temperatures permits LAMP to be incorporated in polymer-based microdevices instead of more traditional and expensive materials, like glass and silicon that, for being temperature-resistant, are required for PCR-based devices. Unlike PCR, LAMP does not require a denatured template for amplifi cation, and given the usual abundance of generated DNA, the amplifi ed product can often be visualized directly [ 13 ] . For viral detection, in particular, the technique has shown sensitivity at least equivalent to PCR [ 45 ] and even to rPCR [ 46 ] . Coupled to easier sample preparation procedures, these features make LAMP inherently simple and hence especially suitable for POC applications [ 47 ] .

POC tests based on nucleic-acid amplifi cation potentially allow early detection of latently infected animals on targeted high-risk premises, with some examples already being applied in fi eld situations [ 48 ] . However, this would require sample collection and testing from many suspect herds, which will require too demanding manpower in the course of an outbreak. This is probably why existing tests have not been adopted in contingency plans in many countries, although the issue remains controversial [ 12 ] . During the FMD outbreak in 2007, up to 269 samples were analyzed each day [ 38 ] , but larger outbreaks would require higher-throughput testing. Of course, from a certain point above, it is admissible that central laboratories would become overloaded and that true POC devices, able to be manipulated by farmers themselves, would be probably the best (or even unique) solution. This, however, by the reasons pointed above, is still far from reality, although the unstoppable technological advances in this fi eld, coupled to new paradigms for decentralized detection, will more and more shorten the present distance to that goal.

For bioanalysis with prototype biosensors and POC devices, three main types of signal transduction mechanisms have been used: electrochemical, optical, and microgravimetric (mass sensitive). They are well known and have been extensively used in research laboratories for analytical chemistry, holding great promise for new prototype and fully developed bioanalytical and diagnostic microdevices. Among microgravimetric methods, quartz-crystal microbalance (QCM) is the most common; it usually relies on the use of a piezoelectric crystal whose fundamental resonance frequency changes upon successive immobilization of a biorecognition probe and its target. However, the diffi culty of miniaturization, the high cost, and the complex infl uence of multiple interfacial parameters on the sensor response (especially in liquid phase) have hampered wider development of POC devices based on this technique. The applicability of electrochemical methods for nucleic-acid analysis has greatly benefi ted from the emergence of solid electrodes [ 24 ] . Electrochemical-based analytical devices can be relatively simple, rapid, less costly, low-power demanding, and amenable for miniaturization and mass production through standardized microfabrication techniques [ 49 ] .

Optical detection has been the most widely employed transducing principle in biosensing, partially driven by the unending advances of optic applications in telecommunications and information systems. Furthermore, the very high frequency of optical signals is appropriated for the enormous amount of information that can be carried by optical systems and devices [ 24 ] . Conventional optical microscopy has been reliably used for detection and imaging of infectious pathogens (at both cellular and molecular levels), integrated with research and development of new POC diagnostic devices [ 50 ] . Within optical detection methods, chemiluminescence and fl uorescence have been the most widely used for their versatility of designs and applications. Imaging methods usually require bulky and expensive microscopes and camera-equipped microscopy systems, i.e., in off-device formats. Such equipment is obviously unsuitable for POC diagnostics. The innovative technique of optofl uidic seems thus promising in this regard, as this high-throughput and high-resolution on-device technique does not make use of such components [ 51 ] . In optofl uidic devices, the sample fl ows through a metal fi lm-etched array with submicron apertures for imaging, onto a plastic platform.

An intrinsic limitation of conventional optical detection is the interference between closely spaced light waves. Understandably, this is especially limiting for the design and performance of miniaturized devices for multi-analyte detection and identifi cation. However, optical transmission through minuscule structures gained a new impulse with the technique of surface plasmon resonance (SPR), in which light waves are directed to the interface between a metal and a dielectric. The technique is label-free and the immobilized probe can be easily reused, although sensitivity must still be improved [ 24 ] . Moreover, it faces the challenges of other optical techniques for POC diagnosis, namely, the high cost, instrumental complexity, expensiveness of optical components, and diffi culty for miniaturization/portability and mass production. The advent of integrated photodiode detectors is promising for the development of cheap, sensitive, easy-to-use, and easy-to-fabricate fl uorescence-based diagnostic microdevices [ 52 ] . A remarkable milestone might be the shift from current fl uorescent-based detection methods to naked-eye (visual) recognition, which would considerably reduce complexity and costs. These readouts can be recorded as digital images and then transmitted to remote clinicians through trivial and inexpensive telecommunication devices (e.g., digital cameras and scanners); some current examples include the detection of glucose, pH, and proteins [ 53 ] . It is expected that future POC diagnostic devices will become connected to wireless communication and information systems through camera-equipped mobile phone networks coupled to web databases, for diagnostic imaging and telemedicine, especially in remote and resourcelimited regions and settings [ 54 ] . Remote monitoring will not constitute a valuable or even indispensable way for analysis when in-the-fi eld conditions do not allow doing that, but also an approach to improve quality management for tests conducted in the fi eld.

Multiplex PCR and DNA microarrays have been among the most commonly used techniques for the detection and identifi cation of infectious pathogens. Multiplex PCR is frequently limited to the analysis of only a few target genes, owing to interferences between different primer sets in the same reaction vessel. DNA microarrays are usually too expensive, labor intensive, and complex for POC applications; moreover, the microarray assays are usually lengthy due to the slow diffusion-limited hybridization kinetics. On the other hand, lateral-fl ow devices employed for POC diagnosis usually have relatively low sensitivity; moreover, in the most common format (immunochromatographic format, corresponding to the well-known test strips), they do not provide genetic information, thus hindering the assessment of eventual pathogen subtypes and/ or drug resistance markers. In general, the number of targets that can be simultaneously probed in lateral-fl ow assays is low, thus increasing the cost per assay and limiting the throughput. Also, their degree of multiplexing usually does not reach that of microarrays [ 55 ] .

The last decade has witnessed tremendous advances in microfl uidic sciences and applications for bioanalysis. Microfl uidic devices basically consist in a set of microchambers interconnected through microchannels, imprinted onto a suitable solid platform. After injection into the system, the liquid biological sample fl ows throughout the hydrophilic inner walls of the chambers and channels for fi nal analysis. The fl ow is usually controlled automatically by mechanical valves. A primary advantage of microfl uidics for the development of miniaturized diagnostic devices, especially for POC usage, is the requirement for only very small sample volumes, which permits to save reagents (viz., probes and labels), but also gaining time and sensitivity, as a consequence of the enhanced binding kinetics (unlike in bulky reaction media). It also provides lower power consumption and lower operating costs. Moreover, since the overall analytical process is automated, sample losses and contamination due to human handling can be minimized, in parallel with improved multiplexing capabilities. The confi nement and automation of the process also reduces errors due to human manipulation and increases biosafety. In microfl uidic devices, the occurrence of nucleic-acid hybridization in solution and the enhanced aqueous mixing allow surpassing the kinetic barriers that slow affi nity reactions due to limited diffusion in traditional

microarrays [ 53 ] . Recent developments in microfl uidic technology have pointed towards integrating traditionally off-chip processes into the microdevices. Indeed, signifi cant reduction of bulky, complex, and expensive equipment is mandatory for POC and in-thefi eld diagnostic applications.

Traditional microfl uidic devices usually rely on pressure-driven fl ow (through a syringe pump or pressure injector) or electroosmotic fl ow, but these techniques require external bulky and complex equipment, like a power supply. For POC applications, more suitable methods for fl uid delivery have been developed, namely, mechanical pumping, capillarity, and light-driven motion [ 53 ] . Compared to conventional injection systems, as fl ow-injection analysis (FIA), microfl uidics enables achieving lower detection limits, as a result of enhanced probe/target binding kinetics [ 56 ] and of time-dependent target pre-concentration in microchambers. Droplet-based schemes offer a signifi cant improvement in microfl uidics, due to the ability to independently control each free droplet containing the target under analysis. In this way, each single droplet functions as a pump, valve, mixer, solid-phase extractor, and thermocycler, thus greatly simplifying the assay design [ 10 ] .

The fi rst microfl uidic devices were manufactured as glass or silicon platforms, but the high cost of these materials led to the widespread use of polydimethylsiloxane (PDMS) for such purpose. However, some properties of PDMS limit its use for biosensing in microfl uidic devices, e.g., hydrophobicity and swelling/disintegration in organic solvents. In order to prevent some of the limitations of PDMS, other materials have been used, like paper and thermoplastics. These materials, as well as their fabrication process, are cheaper than PDMS, glass, and silicon, making large-scale fabrication more feasible. This low cost also encourages disposability, an important biosafety asset when dealing with infectious agents, and a way to avoid cross-contamination of biological samples. Moreover, these materials are lightweight and hence easy to transport in the form of portable devices. Finally, their fabrication does not require clean-room settings. Thermoplastics are attractive materials for simple, low-cost, and reproducible fabrication of POC devices by well-known replication molding techniques (e.g., injection molding or hot embossing). An example is poly(methyl methacrylate) (PMMA), which is mechanically stable, is optically transparent, and has an easily modifi able surface. Another example is polycarbonate, whose lower thermic conductivity in comparison with glass or silicon turns it amenable for high-temperature PCR applications [ 53 ] . Patterned paper-based microfl uidic devices are valuable alternatives to test strips. Advantages of paper include its abundance, easiness to use (e.g., clean rooms or other complex and expensive infrastructures for its manipulation are unnecessary), low cost, disposability, and easily patterned with polymers and other molecules by conventional printing techniques (e.g., photolithography, wax and inkjet printing). Its common white color is particularly suitable for the use of colored substrates in quantitative colorimetric tests. Moreover, unlike in test strips and conventional microfl uidics, its porous nature allows capillaritydriven fl uid wicking and fl ow through its structure, without the need for external pumps and pressure source. New three-dimensional structures will enable a vertical fl ow to be added to the sole lateral fl ow of two-dimensional devices, in higher complex structures than those presented by plastic frames. In this way, they may exhibit improved abilities for initial purifi cation and concentration as the liquid wicks throughout the inner layers of the device, until fi nal detection [ 57 ] .

Many current microfl uidic devices still rely on complex and bulky laboratorial (off-chip) equipment for fl uid delivery and control, making their use impractical in fi eld situations, e.g., by emergency response teams [ 53 ] . Other drawbacks faced by microfl uidic systems include biomolecule adsorption to microchannel walls, inaccurate control of temperature, liquid evaporation due to heatgenerating components, and bubble formation [ 5 ] . In addition, future developments in microfl uidic platforms may eventually benefi t from materials with improved analytical performance [ 58 ] , as well as simplicity and cost-effectiveness.

The processes of sample purifi cation and pre-concentration are usually the most complex and cumbersome in biological analysis. In molecular diagnostics, this is particularly true for nucleic-acid isolation procedures, which still remain too complex for in-thefi eld use. One of commonest requirements is a centrifuge, which obviously hinders the integration of such detection schemes within miniaturized analytical devices. In many diagnostic microdevices, such procedures are carried out off-chip, prior to the detection step itself. Moreover, they strongly depend on the characteristics of the specifi c biological sample and require relatively high volumes of raw sample for downstream nucleic-acid amplifi cation. In the last years, lab-on-a-chip devices have emerged as second-generation chips, essentially based on the concept of microfl uidics. By suitable integration of modules for sample processing and analysis in a single device, they offer enhanced fl exibility and discriminatory ability over conventional diagnostic methods and devices. Yet, minimizing and miniaturizing the whole sample preparation procedure towards easiness to use and true POC remains challenging and a relatively underestimated task in the development of POC tests [ 5 ] . Compared to conventional detection techniques, lab-on-achip devices allow the integration and automation of all (or nearly all) steps for sample processing and analysis; the confi nement of the bioelement under measurement in a predefi ned region of interest facilitates its detection and eventual quantifi cation from very small sample volumes. This, in turn, reduces background noise and

hence increases sensitivity [ 53 ] . In lab-on-a-chip devices, minimization of the chemical interferences that result from tight spatial confi nement is usually envisaged, enabling miniaturization and highly sensitive detection. The high mass transfer rate thus achieved is due to the low diffusional distance and high surface-to-volume ratio (S/V) [ 59 ] . Traditional cell analysis and processing, including cell sorting, cell/serum separation (for immunoassays), and cell lysis (for immunoassays or nucleic-acid amplifi cation), can be adapted to POC schemes [ 53 ] . Some principles commonly used to separate and concentrate cells within POC devices are cell size, labeling (fl uorescent or magnetic), electrophoretic mobility, and cell adhesion [ 60 ] . For analysis of real, biological samples, the detection of highly virulent pathogens presumes the ability of detecting very few cells from large sample volumes and, concurrently, washing out sample contaminants (e.g., other cells), in order to prevent, for instance, downstream PCR inhibition and microchannel clogging [ 61 ] . In particular, environmental water samples may contain certain substances, like humic acids, that inhibit PCR reactions, able to drastically decrease the resulting signals. The presence of contaminants in biological samples may be particularly troublesome in microfl uidic assays for veterinary applications.

A particular advantage of bioanalysis with lab-on-a-chip devices concerns the processing of pathogen RNA. Owing to the confi ned environment of the purifi cation steps and to the requirement for minimal user handling, the probability for RNA contamination and degradation by ubiquitous RNases is highly decreased [ 62 ] . Schemes employing nucleic-acid extraction through detergents rather than high temperature-operating lytic enzymes coupled with isothermal (e.g., LAMP) instead of PCR and RT-PCR amplifi cation processes are also preferred in this regard. In this way, the concept of microfl uidics might be able to address a recurrent gap in veterinary literature-the lack of information about RNA quality and integrity, which further complicates the standardization of RT-PCR procedures [ 34 ] . Several commercial multiplexed POC tests for diagnosis of infl uenza and other respiratory viruses are already available, as the FilmArray RP (BioFire Diagnostics, Salt Lake City/UT, United States), the xTAG RVP (Luminex, Toronto, Canada), and the Xpert Flu A Panel (Cepheid, Sunnyvale/CA, United States), consisting in closed systems that include sample preparation and detection by integrated RT-PCR [ 63 , 64 ] . However, these systems may not be able to detect low viral load specimens, as is the case of the Xpert Flu A Panel with some important avian infl uenza viruses. In addition, economic constraints still restrict full applicability of some of these tests in POC testing. For the Xpert Flu A panel, it was estimated a cost of 45 euros per test, compared to 15 euros for the antigenic tests [ 63 ] . Current lab-ona-chip devices, despite being simpler than conventional laboratory analytical apparatus, still require complex and somewhat expensive fabrication procedures onto plastic or glass substrates, thus severely limiting their affordability and availability by poor countries. Table 1 displays some literature references about proof-of-principle schemes and POC devices for detection and identifi cation of some pathogens of veterinary importance. 

An emergent topic in the development of new bioanalytical procedures, structures, and systems is nanotechnology, particularly for the generation of useful nanostructures for diagnostic applications; this is the so-called fi eld of "nanobiotechnology". Novel and improved electronic devices and biosensor platforms have emerged as a consequence of the inherent small size, enlarged surface area, and unusual optical, magnetic, catalytic, and mechanical properties of nanomaterials, unlike those of bulk materials [ 24 ] . Depending on their specifi c nature, for biosensing, nanomaterials may act as labels (including signal amplifi cation), as biomolecule immobilization supports, or even as probes for specifi c biotarget anchoring. Certain nanomaterials can also be used for pre-concentration of biological targets. Among these applications, labeling has been the most commonly employed. Label-based detection methods are usually more time-consuming and labor intensive than label-free methods due to the labeling steps. Labels have also limited shelf lives and are subjected to leakage from sensing surfaces. However, label-based methods usually provide superior performance, especially in terms of sensitivity, than label-free ones. Moreover, standardized protocols with labeling procedures are already available. Fluorescence labeling has been, by far, the most common approach in this regard, although suffering from pH sensitivity and photobleaching over time [ 53 ] . Such handicaps and the advent of nanoengineering have propelled the search and development of new and improved labels. Nanoparticles (NPs) have been the most widely employed type of nanomaterials for biosensing, especially metallic NPs. Metallic NPs are inorganic NPs that exhibit improved physicochemical characteristics compared to fl uorescent labels, including higher sensitivity. In general, they are suitable for construction of highdensity bioanalytical devices, taking advantage of their high signalto-noise ratio (S/N). They are easily synthesizable and functionalized (by simple mixing at room temperature) and have a controlled, self-assembled surface structure [ 24 ] . Gold nanoparticles (GNPs), in particular, are already used frequently in molecular diagnosis; some of their advantages include low toxicity and versatility for many specifi c biorecognition applications and schemes. One common way to enhance the GNP signal even further, and thus the sensitivity of detection, is the inclusion of a fi nal step of silver staining ("silver enhancement"), yielding detection schemes able to preclude the use of a prior PCR amplifi cation step. The high sensitivity exhibited by many NP-based detection layouts, especially in the form of microarrays, has enabled to avoid a prior step of nucleic-acid amplifi cation [ 69 ] .

Quantum dots (QDs) constitute another class of metallic NPs, able for fl uorescence tagging. They are much brighter and more photostable than conventional organic fl uorophores. Plus, their color can be directly correlated with size, while exhibiting very broad excitation wavelength windows, very narrow emission wavelength windows, and large Stokes shifts, allowing excitation at wavelengths far removed from their emission peaks [ 70 ] . Since QDs of different emission peaks (according to their different sizes) can be excited using a single wavelength excitation source, detection of multiple targets in complex biological systems is a hallmark of these NPs [ 71 ] . Another alternative to the overlapping of closely spaced fl uorescence emission peaks and consequent limitation of the maximum number of fl uorescent dyes that can be discriminated when simultaneously testing multiple pathogens in a single PCR tube is the use of masscode tagging, with a panel of distinct labels with different molecular weights. After an initial step of multiplexed (RT-)PCR using primers labeled with the masscode tags, unincorporated primers are removed, and the photo-cleavable tags of amplifying primers are then released by UV irradiation. Subsequent mass spectrometry analysis assigns each identifi ed tag to its specifi c pathogen [ 1 ] . In principle, the multiplexing ability will only be limited by the highest primer concentration contained by a PCR mix. The method was applied to the identifi cation of respiratory pathogens [ 72 ] and hemorrhagic viruses [ 73 ] . It offers a rapid, specifi c, sensitive, and cost-competitive alternative to conventional PCR and RT-PCR for disease diagnosis through POC devices. Nevertheless, some diffi culties persist in miniaturizing mass spectrometer devices.

Among metallic NPs are also magnetic NPs (MNPs). Equivalent designations frequently found in the literature include "magnetic nanobeads", "nanomagnets", "nanomagnetic beads", "nanomagnetic spheres", and "nanospheres". They have been vastly employed in many biosensor layouts for diagnosis. Despite not matching the nanosize of molecular recognition probes and targets, their microscaled counterparts, magnetic microparticles, are frequently preferred as magnetic labels for biosensing in view of the easiness for detecting the lesser abundant microbeads by routine optical microscopy or by magnetic detection and by the easiness of the purifi cation process, thus allowing more effi cient removal of nonspecifi cally bound labels, with enhancement of the assay performance [ 74 ] . However, the higher S/V of nanobeads provides much more binding sites for bioprobe and biotarget anchoring and hence a higher S/N [ 5 ] . Very often, magnetic particles are used for target pre-concentration from large initial sample volumes and purifi cation, in parallel with the detection step itself being carried out through another particle that works as the label (e.g., fl uorophore or GNP). In this case, there is an initial capture of the target by the probe-functionalized magnetic particle, followed by releasing of the target ("debinding") for fi nal detection. Through magnetically controlled removal of nonspecifi cally bound beads (magnetic washing), improved sensitivity can be achieved upon elimination of the time-consuming washing step of nonspecifi cally bound molecules [ 75 ] . This process can, for example, improve signifi cantly the detection specifi city of genomic RNA, since RNA enrichment due to magnetic confi nement also precludes the effect of common interfering substances and common RNA inhibitors [ 76 ] . In addition, the use of magnetic beads permits testing optically opaque samples [ 29 ] , which is the case of many crude biological samples. Magnetic particles can be manipulated off-chip by a permanent magnet, making easier the design of disposable and inexpensive tests. Moreover, magnetic interactions are not affected by surface charges, pH, ionic strength, or temperature, being thus compatible with most biochemical processes [ 10 ] .

Unlike inorganic NPs, organic NPs have enhanced structural fl exibility and biocompatibility, while being biodegradable. Liposomes constitute an attractive type of organic NPs for effi cient DNA-probe labeling and for signal amplifi cation. This is commonly achieved by fi lling liposome particles with dye and fl uorophore molecules, which amplify the response signal and are able to yield quantitative results. Another way of using liposomes in biosensing is in conjunction with resistive techniques. As such, negatively charged liposomes, upon binding to immobilized DNA chains (which are also negative), form giant negatively charged surfaces that repel the target DNA chain, leading to shifts in the electrochemical response [ 24 ] .

In the last years, chemistry research has rendered a range of new structures based on carbon allotropes. The most promising for biosensing purposes seem to be carbon nanotubes (CNTs), both in the form of single-(SWCNT) or multi-walled CNTs (MWCNTs), depending on the number of cylindrical layers, with unique electronic properties and enlarged surface area for DNA immobilization. They also possess high electrical conductivity (similar to copper and much higher than in polymers), physical robustness, and chemical inertness. Each nanotube may act as an individual nanoelectrode, with suffi cient free space between neighboring nanotubes preventing the overlap of their diffusion layers, therefore yielding high S/N values and hence improved detection limits [ 77 ] . By providing high sensitivity, they are amenable to PCR-free detection. Their production is sometimes unacceptably irreproducible for ultrasensitive detection, but this has been circumvented by using cheap CNT arrays for multiple biological targets as a way of averaging out between different batches [ 78 ] .

The recent advances in nucleic-acid synthesis and modifi cation processes and the discovery of nucleic acids with catalytic and regulatory activities have prompted the development of nanoengineered nucleic-acid analogues with new and improved abilities for biorecognition and diagnostic purposes. Among them are aptamers; they are synthetic nucleic acids able to interact with molecular or cellular targets with high specifi city and sensitivity for their ability to fold into many tertiary conformations. Aptamers can be generated by "Systematic Evolution of Ligands by Exponential Enrichment" (SELEX), a combinatorial procedure that starts with a pool of candidate nucleic-acid molecules to generate a nucleicacid library [ 79 ] . Compared to antibodies, nucleic-acids can be synthesized in a more reproducible way, have longer shelf lives, and can be reversibly denatured without loss of activity. A remarkable characteristic of these probes for biosensing is that they do not require prior knowledge about the molecular differences between the specifi c target and nonspecifi c ones. As shown in cancer diagnosis, the DNA sequences from the DNA library that bind the cell-surface markers of a cancer cell can be determined by comparison with those that bind a healthy (control) cell. In addition, detection occurs before the corresponding antibody against that cancer has been produced [ 80 ] . This process is obviously attractive for application to the diagnosis of infectious diseases as well. The high selectivity and sensitivity achieved with aptamers permits eliminating sample pretreatment and is thus promising for POC applications [ 53 ] . The inability to distinguish the fl uorescent signal from labeled and unlabeled probes is a common problem in microfl uidic devices, since labeled probes that did not bind targets cannot be washed out from the microchannels. Different fl uorescent labels can be used to tag the probe and the target, with the detection proceeding via fl uorescence resonance energy transfer (FRET) upon the occurrence of the bioaffi nity reaction. However, this procedure is unpractical in bioanalysis owing to the cumbersome dual labeling procedure [ 81 ] . In the case of DNA detection, this can be circumvented with the use of molecular beacons (MBs), which can be considered a particular type of aptamers. MBs are singlestranded oligonucleotides with a hairpin (stem-and-loop) structure, labeled with a fl uorophore in one extremity of the chain and a fl uorescence quencher in the other extremity. The close proximity between the extremities prevents fl uorescence emission, but when a hybridization event occurs with a complimentary chain, the structure becomes linearized and hence fl uorescence arises. In this way, target labeling is unnecessary. Another type of synthetic nucleic-acid analogues is constituted by peptide nucleic acids (PNAs), which are in which the sugar-phosphate backbone is replaced by a peptidic structure. When used as probes in nucleicacid recognition systems, they allow very selective and sensitive hybridization in low ionic-strength media, while having high thermal stability [ 82 ] . For being electrically uncharged, PNAs are suitable to promote the occurrence of biochemical events triggered by the formation of the negatively charged PNA/single-stranded DNA hybrid, i.e., a kind of "on/off" processes.

Biosensing schemes reported in the literature employing at least one of the nanotechnology-based structures described above are depicted in Table 2 , together with the transduction mechanism employed and performance quantifi cation. a Micro-scaled magnetic particle labels are also considered in this table

The advances observed on the past decades in proteomics and genomics have led to the discovery of novel diagnostic biomarkers for pathogens relevant in human medicine. In parallel, cuttingedge developments in materials science and in nanotechnology have also been registered. Veterinary science and practice "took the train" and, as such, have been greatly favored from such advances. Microfl uidic technologies and nanoengineered structures, especially when coupled together, have led to an unprecedented degree of high-throughput, large-scale genetic analysis, even at wholegenome levels. Ultimately, the high-throughput and multiplexing abilities of in vivo (implanted or swallowed) nanosensor arrays should be able to monitor animals' physiology and health status during their entire lifetime, and even beyond, intended to track and assess the quality of animal products for human feeding. In this way, the current shortcomings related with the limited number of sanitary surveillance resources that can be allocated to guarantee proper product origin, stocking, and shipping could be circumvented. So far, only few POC schemes and devices have reached the exquisite sensitivity thresholds required for detection of nucleicacid traces in unamplifi ed biological samples, which is the ultimate goal of nucleic-acid testing. As for human diagnostics, the veterinary medicine and practice still lack the commercial availability of more POC devices, more probably as a result of manufacturing and commercial cost-effectiveness constraints than to a shortage of fundamental knowledge. While remaining too expensive for single testing, many tests targeted for POC diagnosis will ultimately prove to be cost-effective when savings with unnecessary laboratory manpower are taken into account. Other major challenges are the need for initial investments that are often prohibitive for small companies and the usual diffi culties for obtaining regulatory approvals for testing and commercialization. For effective improvement of human health, more adequate and coordinated actions to face animal diseases are needed, especially concerning livestock. This includes a more effective technology transfer from developed countries to those where diseases are prevalent and where disease preventive measures may be crucial to avoid or contain epidemics. Probably still without meritorious examples in the world, more effective communication and coordination among public health, animal health, and wildlife disease surveillance authorities will be necessary to tackle the problems posed by common and hazardous veterinary diseases, especially in situations of outbreaks endangering animal and human health as well.

Technology, public policy and control of transboundary livestock diseases in our lifetimes

New Cryptosporidium genotypes in HIV-infected persons

The role of companion animals in the emergence of parasitic zoonoses

Trends in dengue diagnosis

Micro-total analysis system for virus detection: microfl uidic pre-concentration coupled to liposome-based detection

Prevalence of enteric zoonotic organisms in cats

Utility of a panviral microarray for detection of swine respiratory viruses in clinical samples

Rapid fi eld detection assays for Bacillus anthracis , Brucella spp., Francisella tularensis and Yersinia pestis

Rapid detection of foot-and-mouth disease virus using a fi eld-portable nucleic acid extraction and real-time PCR amplifi cation platform

Catching bird fl u in a droplet

Biosensors as rapid diagnostic tests for tropical diseases

The use of new technologies for rapid, fi eld-based (point-of-care) testing in the detection of emergency animal diseases. Australian Centre of Excellence for Risk Analysis (ACERA

Novel reverse transcription loop-mediated isothermal amplifi cation for rapid detection of foot-and-mouth disease virus

Nanoscience in veterinary medicine

Relationship between clinical signs and transmission of an infectious disease and the implications for control

Progress towards the development of simple and rapid diagnostic tests away from centralised laboratories. World Association of Veterinary Laboratory Diagnosticians-16th international symposium

Loop mediated isothermal amplifi cation combined with nucleic acid lateral fl ow strip for diagnosis of cyprinid herpes virus-3

Point-of-care nucleic acid testing for infectious diseases

Farmers, animal disease reporting and the effect of trust: a study of West Australian sheep and cattle farmers

Improved diagnosis for nine viral diseases considered as notifi able by the World Organization for Animal Health

New emerging zoonoses: a challenge and an opportunity for the veterinary profession

Point-of-care testing (POCT): current techniques and future perspectives

Trends in DNA biosensors

Analytical connotations of pointof-care testing

Evaluation of diagnostic tests for infectious diseases: general principles

Pediatric Dengue Vaccine Initiative (PDVI) (2009) Evaluation of commercially available anti-dengue virus immunoglobulin M tests

Assessing agreement between point of care and laboratory results for lipid testing from a clinical perspective

Special Programme for Research and Training in Tropical Diseases (TDR) (2009) Dengue: guidelines for diagnosis, treatment, prevention and control

ICSH Guideline for worldwide point-of-care testing in haematology with special reference to the complete blood count

Nanotechnologies applied to veterinary diagnostics

Semi-synthetic nucleic acid-protein conjugates: applications in life sciences and nanobiotechnology

Detection of poly (U) hybridization using azido modifi ed poly (A) coated piezoelectric crystals

Improving the analysis of quantitative PCR data in veterinary research

Electrochemical genosensor design: immobilisation of oligonucleotides onto transducer surfaces and detection methods

Design and optimization of a novel reverse transcription linear-after-the-exponential PCR for the detection of foot-and-mouth disease virus

Direct sequence detection of structured H5 infl uenza viral RNA

Pan-serotypic detection of foot-and-mouth disease virus by RT linear-after-theexponential PCR

New developments in the diagnosis of bloodstream infections

Development and initial results of a low cost, disposable, point-of-care testing device for pathogen detection

Development and evaluation of a novel loopmediated isothermal amplifi cation method for rapid detection of severe acute respiratory syndrome coronavirus

Field detection of avian infl uenza virus in wild birds: evaluation of a portable rRT-PCR system and freeze-dried reagents

Point-of-care testing system enabling 30 min detection of infl uenza genes

A review of RT-PCR technologies used in veterinary virology and disease control: sensitive and specifi c diagnosis of fi ve livestock diseases notifi able to the World Organisation for Animal Health

Real-time reverse transcription loop-mediated isothermal amplifi cation for rapid detection of West Nile virus

A loop mediated isothermal amplifi cation assay for detection of Hendra virus in the fi eld

Loop-mediated isothermal amplifi cation (LAMP): a rapid, accurate, and cost-effective diagnostic method for infectious diseases

Clinical and laboratory investigations of the outbreaks of foot-and-mouth disease in southern England in

Recent trends in electrochemical DNA biosensor technology

On-chip erythrocyte deformability test under optical pressure

Optofl uidic microscopy-a method for implementing a high resolution optical microscope on a chip

An integrated fl uorescence detection system for lab-on-a-chip applications

Microfl uidics for medical diagnostics and biosensors

Mobile phone based clinical microscopy for global health applications

Development of a magnetic bead microarray for simultaneous and simple detection of four pestiviruses

Artifi cial receptors in serologic tests for the early diagnosis of dengue virus infection

Capillary pumps for autonomous capillary systems

Quantifying colorimetric assays in paper-based microfl uidic devices by measuring the transmission of light through paper

Biochip-compatible packaging and microfl uidics for a silicon opto-electronic biosensor

Micro-and nanotechnology in cell separation

Integrated capture, concentration, polymerase chain reaction, and capillary electrophoretic analysis of pathogens on a chip

Microfl uidics-based extraction of viral RNA from infected mammalian cells for disposable molecular diagnostics

Evaluation of the Xpert Flu A Panel nucleic acid amplifi cation-based point-of-care test for infl uenza A virus detection and pandemic H1 subtyping

Comparison of two multiplex methods for detection of respiratory viruses: FilmArray RP and xTAG RVP

Predicting viruses accurately by a multiplex microfl uidic loop-mediated isothermal amplifi cation chip

Cell lysis and DNA extraction of gram-positive and gram-negative bacteria from whole blood in a disposable microfl uidic chip

Detection of African swine fever virus by loop-mediated isothermal amplifi cation

Rapid isolation and detection of aquaculture pathogens in an integrated microfl uidic system using loop-mediated isothermal amplifi cation

Multiplexed, rapid detection of H5N1 using a PCR-free nanoparticle-based genomic microarray assay

Single-molecule quantum-dot fl uorescence resonance energy transfer

Less is more in medicine

Diagnostic system for rapid and sensitive differential detection of pathogens

MassTag polymerase chain reaction for differential diagnosis of viral hemorrhagic fevers

Fluidic force discrimination. US Patent application publication

A biosensor based on magnetoresistance technology

An integrated microfl uidic system using magnetic beads for virus detection

Emerging synergy between nanotechnology and implantable biosensors: a review

Carbon nanonets-spark new electronics

A label-free DNA aptamer-based impedance biosensor for the detection of E. coli outer membrane proteins

Aptamerbased microfl uidic device for enrichment, sorting, and detection of multiple cancer cells

Fast and sensitive DNA analysis using changes in the FRET signals of molecular beacons in a PDMS microfl uidic channel

Peptide nucleic acid probes for sequencespecifi c DNA biosensors

Rapid parallelized and quantitative analysis of fi ve pathogenic bacteria by ITS hybridization using QCM biosensor

Target discrimination by surfaceimmobilized molecular beacons designed to detect Francisella tularensis

Portable optoelectronic biosensing platform for identifi cation of mycobacteria from the Mycobacterium tuberculosis complex

A DNA sequence-specifi c electrochemical biosensor based on alginic acid-coated cobalt magnetic beads for the detection of E. coli

Selection and characterization of DNA aptamers for use in detection of avian infl uenza virus H5N1

Salmonella detection using 16S ribosomal DNA/RNA probe-gold nanoparticles and lateral fl ow immunoassay

A fi eld-deployable colorimetric bioassay for the rapid and specifi c detection of ribosomal RNA

A multiplex nanoparticle-based bio-barcoded DNA sensor for the simultaneous detection of multiple pathogens

A novel electrochemical biosensor based on dynamic polymerase-extending hybridization for E. coli O157:H7 DNA detection

Electrochemical DNA biosensor based on chitosan/nano-V 2 O 5 /MWCNTs composite fi lm modifi ed carbon ionic liquid electrode and its application to the LAMP product of Yersinia enterocolitica gene sequence

Aggregation effects of gold nanoparticles for single-base mismatch detection in infl uenza A (H1N1) DNA sequences using fl uorescence and Raman measurements

Electrically active magnetic nanoparticles as novel concentrator and electrochemical redox transducer in Bacillus anthracis DNA detection

DNA probe functionalized QCM biosensor based on gold nanoparticle amplifi cation for Bacillus anthracis detection

DNA sensor based on vapour polymerised pedot fi lms functionalised with gold nanoparticles

DNA sequence detection based on Raman spectroscopy using single walled carbon nanotube

An autonomous CMOS hysteretic sensor for the detection of desorption-free DNA hybridization

Fe 2 O 3 @Au core/shell nanoparticle-based electrochemical DNA biosensor for Escherichia coli detection

Direct detection of unamplifi ed DNA from pathogenic mycobacteria using DNAderivatized gold nanoparticles

High sensitivity DNA detection using gold nanoparticle functionalized polyaniline nanofibres

Hydrogel based QCM aptasensor for detection of avian infl uenza virus

Impedimetric detection of singlestranded PCR products derived from methicillin resistant Staphylococcus aureus (MRSA) isolates

Magnetic bead-based DNA detection with multi-layers quantum-dots labeling for rapid detection of Escherichia coli O157:H7

Peptide nucleic acid-based (PNA) array for the antigenic discrimination of canine parvovirus

Rapid detection of avian infl uenza virus in chicken fecal samples by immunomagnetic capture reverse transcriptase-polymerase chain reaction assay