key: cord-0027719-4d123qhc
authors: Ding, Wangfei; Alharbi, Abdullah; Almadhor, Ahmad; Rahnamayiezekavat, Payam; Mohammadi, Masoud; Rashidi, Maria
title: Evaluation of the Performance of a Composite Profile at Elevated Temperatures Using Finite Element and Hybrid Artificial Intelligence Techniques
date: 2022-02-14
journal: Materials (Basel)
DOI: 10.3390/ma15041402
sha: 90bb6ee3a3ea2fbdecb643bbee297eb285621137
doc_id: 27719
cord_uid: 4d123qhc

It is very important to keep structures and constructional elements in service during and after exposure to elevated temperatures. Investigation of the structural behaviour of different components and structures at elevated temperatures is an approach to manipulate the serviceability of the structures during heat exposure. Channel connectors are widely used shear connectors not only for their appealing mechanical properties but also for their workability and cost-effective nature. In this study, a finite element (FE) evaluation was performed on an authentic composite model, and the behaviour of the channel shear connector at elevated temperature was examined. Furthermore, a novel hybrid intelligence algorithm based on a feature-selection trait with the incorporation of particle swarm optimization (PSO) and multi-layer perceptron (MLP) algorithms has been developed to predict the slip response of the channel. The hybrid intelligence algorithm that uses artificial neural networks is performed on derived data from the FE study. Finally, the obtained numerical results are compared with extreme learning machine (ELM) and radial basis function (RBF) results. The MLP-PSO represented dramatically accurate results for slip value prediction at elevated temperatures. The results proved the active presence of the channels, especially to improve the stiffness and loading capacity of the composite beam. Although the height enhances the ductility, stiffness is significantly reduced at elevated temperatures. According to the results, temperature, failure load, the height of connector and concrete block strength are the key governing parameters for composite floor design against high temperatures.

Since composite beams have great advantages such as considerable span length, small floor depth, and high stiffness, they are widely used in a variety of structures and buildings [1] [2] [3] . Shear connectors are typically employed in composite floor systems due to their superior shear performance in comparison with other structural elements. Different types of shear connectors have been proposed in which each one could address a significant issue of composite floor systems [4] . Generally, connectors are divided into two major element (FE) model was constructed and validated using ABAQUS software so that the models constructed were in good agreement with the test results. Push-out tests were also simulated using the ABAQUS program, and results were collected into datasets. Secondly, with respect to the reviewed studies, a hybrid AI algorithm was developed to predict the FE results. Accordingly, a feature selective (FS) algorithm was used in addition to a hybrid neural network including MLP and PSO algorithms to predict the slip strength of the channel connector at elevated temperatures and select the most crucial parameter in the design of composite floor system.

In this part, an experimental procedure for the study of channel connectors at elevated temperature is briefly discussed, similar to the procedure used in [5] . The monotonic push-out tests were performed on channel shear connectors at elevated temperatures to investigate the strength properties of the composite system at high temperatures.

The test sample is a composite floor system that included an IPE270 profile, a channel as a connector that has been welded to each profile flange by fillet weld and two concrete blocks with dimensions 150 mm × 250 mm × 400 mm placed on both sides of the IPE270 profile ( Figure 1 ). In order to prevent the cracking of concrete, a transverse closed rectangular reinforcement with a diameter of 10 mm per concrete block was provided. The reinforcement applied in rectangular closed stirrups in two upper and lower rows was kept in two rows of vertical reinforcement. shear connector system. First, in order to obtain a proper database of relevant data, a finite element (FE) model was constructed and validated using ABAQUS software so that the models constructed were in good agreement with the test results. Push-out tests were also simulated using the ABAQUS program, and results were collected into datasets. Secondly, with respect to the reviewed studies, a hybrid AI algorithm was developed to predict the FE results. Accordingly, a feature selective (FS) algorithm was used in addition to a hybrid neural network including MLP and PSO algorithms to predict the slip strength of the channel connector at elevated temperatures and select the most crucial parameter in the design of composite floor system.

In this part, an experimental procedure for the study of channel connectors at elevated temperature is briefly discussed, similar to the procedure used in [5] . The monotonic push-out tests were performed on channel shear connectors at elevated temperatures to investigate the strength properties of the composite system at high temperatures.

The test sample is a composite floor system that included an IPE270 profile, a channe as a connector that has been welded to each profile flange by fillet weld and two concrete blocks with dimensions 150 mm × 250 mm × 400 mm placed on both sides of the IPE270 profile ( Figure 1 ). In order to prevent the cracking of concrete, a transverse closed rectangular reinforcement with a diameter of 10 mm per concrete block was provided. The reinforcement applied in rectangular closed stirrups in two upper and lower rows was kept in two rows of vertical reinforcement. A typical load-slip curve is depicted in Figure 2 [69] . The knowledge about the stiffness of composite beam has been primarily used in the equation of the partial interaction theory of composite steel-concrete beams. Since there is no linear relationship between load and slip, a few mathematical expressions are needed to explain the shear connector load-slip relationship throughout the curves. Therefore, it is difficult to find a typical regression formula for the shear connector stiffness. Based on the temperature corresponding to the taken time, standard provisions have identified the typical fire curve for performing elevated temperature tests and the three most common standard fire curves are shown in Figure 3 . A typical load-slip curve is depicted in Figure 2 [69] . The knowledge about the stiffness of composite beam has been primarily used in the equation of the partial interaction theory of composite steel-concrete beams. Since there is no linear relationship between load and slip, a few mathematical expressions are needed to explain the shear connector load-slip relationship throughout the curves. Therefore, it is difficult to find a typical regression formula for the shear connector stiffness. Based on the temperature corresponding to the taken time, standard provisions have identified the typical fire curve for performing elevated temperature tests and the three most common standard fire curves are shown in Figure 3 . 

The ABAQUS/CAE v.14.1 (2014, Simulia, Providence, RI, USA) was employed to model the presented test specimen(s). The Finite Element (FE) models were adjusted to replicate the empirical tests [70] . To assure that the FE model was able to verify the real specimen(s), a range of element types and mesh matrices were carried out as trial-anderror procedures to find a sustainable structured mesh [71, 72] . Figure 4 shows a 3D view of the model and the inner cut to demonstrate the position and details of the shear connector and transverse rectangular reinforcements. 

The ABAQUS/CAE v.14.1 (2014, Simulia, Providence, RI, USA) was employed to model the presented test specimen(s). The Finite Element (FE) models were adjusted to replicate the empirical tests [70] . To assure that the FE model was able to verify the real specimen(s), a range of element types and mesh matrices were carried out as trial-anderror procedures to find a sustainable structured mesh [71, 72] . Figure 4 shows a 3D view of the model and the inner cut to demonstrate the position and details of the shear connector and transverse rectangular reinforcements. 

The ABAQUS/CAE v.14.1 (2014, Simulia, Providence, RI, USA) was employed to model the presented test specimen(s). The Finite Element (FE) models were adjusted to replicate the empirical tests [70] . To assure that the FE model was able to verify the real specimen(s), a range of element types and mesh matrices were carried out as trial-and-error procedures to find a sustainable structured mesh [71, 72] . Figure 4 shows a 3D view of the model and the inner cut to demonstrate the position and details of the shear connector and transverse rectangular reinforcements. 

The ABAQUS/CAE v.14.1 (2014, Simulia, Providence, RI, USA) was employed to model the presented test specimen(s). The Finite Element (FE) models were adjusted to replicate the empirical tests [70] . To assure that the FE model was able to verify the real specimen(s), a range of element types and mesh matrices were carried out as trial-anderror procedures to find a sustainable structured mesh [71, 72] . Figure 4 shows a 3D view of the model and the inner cut to demonstrate the position and details of the shear connector and transverse rectangular reinforcements. 

The selected interaction for different sections was surface-to-surface mode, and different constraints were defined for different parts of the frame [73] . Each channel connector was assumed to be a fixed member and defined as a tie section on the top of the flange. In addition, the diagonal bracing connections were simulated as couplings. The contact properties were designated as tangential contacts with a 0.3 friction coefficient. The lateral loads were applied to the main reference point which was placed at the exterior edge of the web. Moreover, the monotonic loading was acquired using the time coefficient description. A combination of the quadrilateral four-noded shell (S4R) and linear triangular (S3) elements was conducted to assimilate the composite sections ( Figure 5 ). Table 1 presents the employed geometrics of the channels which have been simulated in the ABAQUS. Other properties and features used were as discussed in the experimental section. 

The selected interaction for different sections was surface-to-surface mode, and di ferent constraints were defined for different parts of the frame [73] . Each channel con nector was assumed to be a fixed member and defined as a tie section on the top of th flange. In addition, the diagonal bracing connections were simulated as couplings. Th contact properties were designated as tangential contacts with a 0.3 friction coefficien The lateral loads were applied to the main reference point which was placed at the exterio edge of the web. Moreover, the monotonic loading was acquired using the time coefficien description. A combination of the quadrilateral four-noded shell (S4R) and linear triangu lar (S3) elements was conducted to assimilate the composite sections ( Figure 5 ). Table  presents the employed geometrics of the channels which have been simulated in th ABAQUS. Other properties and features used were as discussed in the experimental sec tion. To simulate the effect of fire on the model, Eurocode2 and Eurocode3 British Standards Institution provisions were employed for concrete and steel, respectively. Figures 6-9 show the used standard curves for both concrete and steel in the FE model. Figure 10 shows the step-by-step sequence of the typical shear connector deformation at the ambient temperature. The exhibited deformations could be verified with the real test specimens. 

The selected interaction for different sections was surface-to-surface mode, and different constraints were defined for different parts of the frame [73] . Each channel connector was assumed to be a fixed member and defined as a tie section on the top of the flange. In addition, the diagonal bracing connections were simulated as couplings. The contact properties were designated as tangential contacts with a 0.3 friction coefficient. The lateral loads were applied to the main reference point which was placed at the exterior edge of the web. Moreover, the monotonic loading was acquired using the time coefficient description. A combination of the quadrilateral four-noded shell (S4R) and linear triangular (S3) elements was conducted to assimilate the composite sections ( Figure 5 ). Table 1 presents the employed geometrics of the channels which have been simulated in the ABAQUS. Other properties and features used were as discussed in the experimental section. To simulate the effect of fire on the model, Eurocode2 and Eurocode3 British Standards Institution provisions were employed for concrete and steel, respectively. To simulate the effect of fire on the model, Eurocode2 and Eurocode3 ards Institution provisions were employed for concrete and steel, respectiv 9 show the used standard curves for both concrete and steel in the FE mod To simulate the effect of fire on the model, Eurocode2 and Eurocode3 ards Institution provisions were employed for concrete and steel, respectiv 9 show the used standard curves for both concrete and steel in the FE mod Figure 10 shows the step-by-step sequence of the typical shear connecto at the ambient temperature. The exhibited deformations could be verified test specimens.

Step-by-step deformation of the model. Figure 11 illustrates a schematic view of the typical channel at 700 °C Figure 10 shows the step-by-step sequence of the typical shear connecto at the ambient temperature. The exhibited deformations could be verified test specimens.

Step-by-step deformation of the model. Figure 11 illustrates a schematic view of the typical channel at 700 °C where the bottom of the connector has failed (the area in red). In addition Figure 10 shows the step-by-step sequence of the typical shear connector deformation at the ambient temperature. The exhibited deformations could be verified with the real test specimens. Step-by-step deformation of the model. Figure 11 illustrates a schematic view of the typical channel at 700 °C temperature, where the bottom of the connector has failed (the area in red). In addition, thinning occurred. Step-by-step deformation of the model. Figure 11 illustrates a schematic view of the typical channel at 700 • C temperature, where the bottom of the connector has failed (the area in red). In addition, thinning occurred.

The governing failure mode was a ductile mechanism due to the connector failure at the bottom of the channel web while the concrete block was still serviceable. To demonstrate the authenticity of the ABAQUS results, Figure 12 shows two comparative curves for a better understanding of the accuracy and validation of the FE results. In these curves the models were able to acceptably simulate the load-slip curves for different heats and shear connectors. The governing failure mode was a ductile mechanism due to the c the bottom of the channel web while the concrete block was still serv strate the authenticity of the ABAQUS results, Figure 12 shows two c for a better understanding of the accuracy and validation of the FE resu the models were able to acceptably simulate the load-slip curves for shear connectors. The governing failure mode was a ductile mechanism due to the connector failure at the bottom of the channel web while the concrete block was still serviceable. To demonstrate the authenticity of the ABAQUS results, Figure 12 shows two comparative curves for a better understanding of the accuracy and validation of the FE results. In these curves the models were able to acceptably simulate the load-slip curves for different heats and shear connectors. 

Finally, the results of the FE models that employed both C7530 and C10050 shear connectors are presented in Table 2 , and Figure 13 demonstrates the obtained load-slip curves for the aforementioned models. Based on the obtained results, The C7550 and C10050 models indicated the most stiffened behaviour at ambient heat, and the C10030 model presented the most stiffened state at 850 • C. Both C10030 and C10050 models showed a ductile performance at elevated temperatures. According to Table 2 , using the longer width increased the stiffness of the specimens at ambient temperature. On the other hand, employing longer height improved the ductility especially at 700 • C and 850 • C. The better stiffness at the ambient temperature could be related to the embedded length of the channel which could be increased by enlarging the width. It could also be due to the strength properties of the high-strength concrete block presenting a better bearing capacity. High ductility of the specimens at elevated temperatures could be related to the length of the channel connectors, where increasing the length increased the slip value, while failure load decreases due to fatigue in the channels. Using HSC blocks might be effective as a cover for retaining the rigid state of the steel at elevated temperatures, but this effect could not be considered for safety remarks [32] . 

Finally, the results of the FE models that employed both C7530 and C10050 shear connectors are presented in Table 2 , and Figure 13 demonstrates the obtained load-slip curves for the aforementioned models. Based on the obtained results, The C7550 and C10050 models indicated the most stiffened behaviour at ambient heat, and the C10030 model presented the most stiffened state at 850 °C. Both C10030 and C10050 models showed a ductile performance at elevated tem- 

The applied data in this research were derived from finite element results that eventually formed a database with 1010 rows of inputs. This database has seven inputs and one target output. The summary of this data is shown in Table 3 . 

In this paper, a combination of MLP with PSO algorithm based on the random production of the initial population is utilized. PSO is a universal method of minimization that can be employed to deal with problems whose answer is a point or surface in n-dimensional space. In order to identify the most influential input, instead of traditional methods, the feature selection technique is utilized, which is the best way to identify the most influential features of a problem.

MLP network is a feed-forward algorithm that can be utilized as a powerful hyper-surface reconstruction tool that is able to successfully map a set of multi-dimensional input data (x N ) . The MLP configuration has been extensively used in static regression applications, and it consists of one input layer, one or more hidden layer(s) and one output layer. The MLP network uses a supervised learning technique called backpropagation for training the network [74] . Figure 14 shows a schematic of the MLP neuron compositions and Figure 15 shows a schematic configuration of the single-layer MLP, which is used in the analysis of the current study. 

In the PSO algorithm, particles are the building blocks of the population, and they work together to obtain the optimum approach to the target [51, 62, 67] . For this reason, it is called swarm intelligence. The most important feature of any particle is its position, and the critical issue is what indicator or target the particle offers and how fast it moves. In this study, the PSO algorithm is employed along with MLP as a unique intelligence algorithm.

The goal of the PSO algorithm is to find the optimal objective function. A flowchart of the PSO algorithm is illustrated in Figure 16 . 

In the PSO algorithm, particles are the building blocks of the population, and they work together to obtain the optimum approach to the target [51, 62, 67] . For this reason, it is called swarm intelligence. The most important feature of any particle is its position, and the critical issue is what indicator or target the particle offers and how fast it moves. In this study, the PSO algorithm is employed along with MLP as a unique intelligence algorithm. The goal of the PSO algorithm is to find the optimal objective function. A flowchart of the PSO algorithm is illustrated in Figure 16 . FS method is preferred in cases where the readability and interpretation of the subjects are important because the discounted values are preserved as the main features in the reduced space. This method of dimensionality leads to the creation of a quality database without deleting helpful information [75] . The feature selection process is divided into four parts including production method, performance evaluation, stop criteria and validation method, which are shown in Figure 17 . 

FS method is preferred in cases where the readability and interpretation of the subjects are important because the discounted values are preserved as the main features in the reduced space. This method of dimensionality leads to the creation of a quality database without deleting helpful information [75] . The feature selection process is divided into four parts including production method, performance evaluation, stop criteria and validation method, which are shown in Figure 17 . In this study, some of the significant features of the channel shear connectors and the concrete blocks are identified through one or more conversions on the input features. Once mapping points from one ample space to another in a smaller space happens, many points may overlap. Feature extraction helps to find new dimensions that have minimal overlap [74] . Given this technique, we can safely say that there is no better combination of inputs than this technique provided. If we were to manually examine all possible modes, the 127 input combination modes would be impossible to verify. If we tried all the possible scenarios with only seven performances, we accelerated the impact of the inputs by about 18 times.

This study deployed a combination of MLP, PSO and FS to develop a hybrid algorithm called MPF for predicting the shear performance of a composite structure consisting of channel shear connectors at elevated temperatures. Figure 18 shows a sequential combination diagram of particle swarm optimization-feature selection (PSO-FS) and multi-layer perceptron (MLP). In PSO, congestion generally begins with a set of random solutions, with each one called a particle. The particle swarm moves in complex space. A function (f) is evaluated at each step by input. In the global version of the PSO, pi represents the most appropriate point in the entire population. A new velocity is obtained for each i particle in each iteration according to the best individual neighbourhood positions. The new speed can be obtained as follows:

When the speed exceeds the specified limit, it will be reset to its proper range. Depending on the speed, each particle changes its position according to the following equation:

where s i = particle's position; v i = particle's velocity; p i = most the appropriate position; w = inertia weight; c 1 and c 2 = acceleration coefficients; and ∅ 1 and ∅ 2 = uniformly distributed random vectors in [0, 1]. Figure 18 . Flowchart of the sequential combination of hybrid MPF algorithm.

Huang et al. [76] suggested ELM as an AI tool for single-layer feed-forward neural network (SLFN) architecture. In ELM, the weights of SLFN inputs are obtained randomly, while the output weights are analytically defined. The most remarkable advantage of the ELM algorithm is its speed in finding the weights of the network; in addition, it can determine all the network factors and prevent unnecessary interference of humans. Unlike other AI tools, ELM is a new tool, suitable for finding the weights of SLFN. Due to its benefits, ELM could gain popularity and workability. The three steps involved in ELM development are: (1) one SLFN is constructed, (2) the weights and biases of the network are randomly selected, and (3) the output weights are calculated by inverting the hidden layer output matrix. 

Huang et al. [76] suggested ELM as an AI tool for single-layer feed-forward neural network (SLFN) architecture. In ELM, the weights of SLFN inputs are obtained randomly, while the output weights are analytically defined. The most remarkable advantage of the ELM algorithm is its speed in finding the weights of the network; in addition, it can determine all the network factors and prevent unnecessary interference of humans. Unlike other AI tools, ELM is a new tool, suitable for finding the weights of SLFN. Due to its benefits, ELM could gain popularity and workability. The three steps involved in ELM development are: (1) one SLFN is constructed, (2) the weights and biases of the network are randomly selected, and (3) the output weights are calculated by inverting the hidden layer output matrix.

In RBF, the input function (f (x) ) is estimated by a set of D-dimensional radial activation functions. Figure 19 indicates the typical architecture of one network with an input layer of D neurons, the output layer of P neurons, a hidden layer of M neurons, biases at each output neuron and adjustable weights between the hidden and output layers. Regarding a set of N data points in a multidimensional space, the main goal of interpolation is to find a function in which every D-dimensional input feature vector (x n = {: i = 1 . . . , D}) has a corresponding P-dimensional target output vector (f n = {: k = 1 . . . , P}). The approximation function f (x) might be explained as a linear combination of radial basis functions in which the output of network kth consists of the sums of weighted hidden layer neurons plus the bias when the system is represented by nth input vector as:

where w kj is the corresponding weight to jth basis function and kth output, h j (X n ) is the output from jth hidden neuron for the input vector (x n ), and w k0 is a bias term at kth output neuron.

Materials 2022, 15, x FOR PEER REVIEW 1

In RBF, the input function (f(x)) is estimated by a set of D-dimensional radial activ functions. Figure 19 indicates the typical architecture of one network with an input of D neurons, the output layer of P neurons, a hidden layer of M neurons, biases a output neuron and adjustable weights between the hidden and output layers. Rega a set of N data points in a multidimensional space, the main goal of interpolation is t a function in which every D-dimensional input feature vector (xn = {: i = 1…, D}) corresponding P-dimensional target output vector (fn = {: k = 1…, P}). The approxim function f(x) might be explained as a linear combination of radial basis functions in the output of network kth consists of the sums of weighted hidden layer neurons pl bias when the system is represented by nth input vector as:

where is the corresponding weight to th basis function and kth output, ℎ ( the output from jth hidden neuron for the input vector ( ), and 0 is a bias term output neuron. 

Three objective criteria, including correlation coefficient (R 2 ), Pearson's corre coefficient (r) and root mean square error (RMSE) were used to evaluate the accur the results and the reliability of the proposed neural network. RMSE is the most com criteria used to measure the accuracy of continuous variables with a quadratic scorin that also measures the average error rate. This square root is the average square diffe between prediction and actual observation. In the case of r, a higher value, up to 1, sents a suitable fit between measured and predicted values, while a negative value s that the model's performance is worse than the average of the developed models. statistical indicators can be characterized as follows: Figure 19 . The architecture of an RBF network.

Three objective criteria, including correlation coefficient (R 2 ), Pearson's correlation coefficient (r) and root mean square error (RMSE) were used to evaluate the accuracy of the results and the reliability of the proposed neural network. RMSE is the most common criteria used to measure the accuracy of continuous variables with a quadratic scoring rule that also measures the average error rate. This square root is the average square difference between prediction and actual observation. In the case of r, a higher value, up to 1, represents a suitable fit between measured and predicted values, while a negative value shows that the model's performance is worse than the average of the developed models. These statistical indicators can be characterized as follows:

where P i = predicted varaible, O i = observed variable and M = number of considered data. Considering the number of data and avoiding overfitting, 70% of the inputs were randomly devoted to the training phase of the models, and the remaining 30% were assigned to the testing phase. All the codes were developed in the MATLAB environment, and available functions of the MATLAB v2019c software (2019, Mathworks, Natick, MA, USA) were used in the developing process.

For the first time, this study uses the FS method to integrate with the MLP-PSO as a hybrid neural network (MPF) to predict the performance of the specific channel shear connector at elevated temperatures. Each algorithm has its own parameters that can be approximated by changing them. To achieve the desired results, a large number of implementations of neural networks with different configurations are taken, and the best settings are obtained for all algorithms and neural networks, which are presented in Tables 4-7 . Table 5 . Parameter characteristics used for MLP in this study.

Levenberg-Marquardt Backpropagation (LMBP) Table 6 . Parameter characteristics used for RBF in this study.

0.02 10 40 Table 7 . Parameter characteristics used for FS in this study.

3 4

A database may contain a lot of input data but not all inputs are suitable for use in the neural network. Some have no effect on the output prediction, and some may cause network deviation. Therefore, with a large number of inputs, finding the best combination is very time-consuming. The number of possible combinations for k members of a set of n members is equal to (1 (n ∼ = k)). For example, in this research, the number of inputs is seven, so the number of combinations of four inputs is 35 states and the total number of possible states is 127. It is evident that the implementation of the neural network and its results for this number of iterations is impossible given the different combinations of neural network settings, so the only way to select different input states and settings is based on past experiences and initial assumptions. Therefore, using the FS method is inevitable, and by running the FS method on our inputs, only seven runs of all inputs will now be checked, and the best combination will be identified. We start with the adjustment of the MPF neural network and try to find the best population with a constant number of repeats equal to 40. The population was identified equal to 125 and the corresponding results are presented in Figure 20 and Table 8 in the test phase.

A database may contain a lot of input data but not all inputs are suitable for use in the neural network. Some have no effect on the output prediction, and some may cause network deviation. Therefore, with a large number of inputs, finding the best combination is very time-consuming. The number of possible combinations for k members of a set of n members is equal to (1 (n  k) ). For example, in this research, the number of inputs is seven, so the number of combinations of four inputs is 35 states and the total number of possible states is 127. It is evident that the implementation of the neural network and its results for this number of iterations is impossible given the different combinations of neural network settings, so the only way to select different input states and settings is based on past experiences and initial assumptions. Therefore, using the FS method is inevitable, and by running the FS method on our inputs, only seven runs of all inputs will now be checked, and the best combination will be identified. We start with the adjustment of the MPF neural network and try to find the best population with a constant number of repeats equal to 40. The population was identified equal to 125 and the corresponding results are presented in Figure 20 and Table 8 in the test phase. After finding the best population, the calculations are performed again to find the optimal number of iterations. As shown in Figure 21 and Table 9 , the number of optimal repeats in the test phase is 45. After finding the best population, the calculations are performed again to find the optimal number of iterations. As shown in Figure 21 and Table 9 , the number of optimal repeats in the test phase is 45. After finding the best parameters for the neural network, it is time to find the optimal input combination through the feature selection technique. As mentioned earlier, in this technique, there is no need to test all possible combinations, and only each set of k members should be tested once. For example, if we want to determine the best combination of inputs with four members, we only run the network once and set nf to four, then four inputs are selected, which have the most effect on the response. Table 10 and Figure 22 specify the best value of k. After finding the best parameters for the neural network, it is time to find the optimal input combination through the feature selection technique. As mentioned earlier, in this technique, there is no need to test all possible combinations, and only each set of k members should be tested once. For example, if we want to determine the best combination of inputs with four members, we only run the network once and set nf to four, then four inputs are selected, which have the most effect on the response. Table 10 and Figure 22 specify the best value of k. According to the results of Table 10 , all the answers are accurate enough and reliable, which proves the validity of both experimental and FE results in datasets. Table 10 presents the results of the MPF algorithm based on the employed precise criteria, where model 4 was selected as the best prediction with impressive evaluation parameters including RMSE = 13.072, r = 0.972 and R 2 = 0.945 and RMSE = 13.533, 0.970 and R 2 = 0.941 for test and train phases, respectively. The small differences between test and train phase results for model 4 indicates that the MPF algorithm accurately predicted the behaviour of the composite floor system at elevated temperatures. In addition, models 2 and 5 were the next accurate predictions among other results. Furthermore, Table 11 indicates the most significant input combinations that the FS technique has chosen, where the load and temperature are the most important parameters for prediction of the slip value. However, four parameters, including load, temperature, compressive strength and channel height are marked as the most effective composition for prediction of the slip. Therefore, in order to enhance the shear strength and the compressive strength, the connector's height should be constant in further designs, and other parameters could also be held constant or considered as lower priority. To limit the slip value, it should be focused on concrete design and finding the best configuration for channel connectors. The best compositions for predicting slip value based on the FS method were tabulated. Figures 23 and 24 reveal the regression diagrams of the aforementioned input models, where four inputs show the most accurate prediction of the slip value. Figure 25 indicates the tolerance diagram of the four input models, in which both test and train phases have a slight difference between measured and experimental values. Table 11 . Most effective inputs based on feature selection.

Number of Combination

After obtaining the best combination for the MPF neural network, it was necessary to check with one or two other neural networks whether the innovative hybrid network is working properly. In this study, RBF and ELM were employed to challenge the MPF results. Given that the best input parameters were obtained by the feature selection technique, trying different combinations at this stage was avoided and two combinations with four and seven inputs are used as per Table 11 . In addition, the neural network settings were as per Table 6 . Figure 26 demonstrates the regression charts of the ELM and RBF, in which the answers for both seven-and four-input models are accurate, indicating the efficiency of using the FS method in this paper and justifying the application of FS in other, similar studies. Figures 27 and 28 present the tolerance diagram with respect to the train and test results of the RBF and ELM, respectively.

As shown in Table 12 and Figure 29 , the best performance parameters for the MPF are RMSE = 13.072, r = 0.972 and R 2 = 0.945, which are indicated as FS-4. As for the ELM, RMSE = 13.286, r = 0.969 and R 2 = 0.938. In addition, for RBF in the test phase, RMSE = 13.884, r = 0.969 and R 2 = 0.939 in the test phase. The best result for RMSE is the lowest value, while for r and R 2 , the best result is 1; therefore, the values closer to 1 are better results. Considering all the conditions stated above, it is clear that the MPF algorithm performs better than the other two algorithms. After obtaining the best combination for the MPF neural network, it was necessary to check with one or two other neural networks whether the innovative hybrid network is working properly. In this study, RBF and ELM were employed to challenge the MPF results. Given that the best input parameters were obtained by the feature selection technique, trying different combinations at this stage was avoided and two combinations with four and seven inputs are used as per Table 11 . In addition, the neural network settings were as per Table 6 . Figure 26 demonstrates the regression charts of the ELM and RBF, in which the answers for both seven-and four-input models are accurate, indicating the efficiency of using the FS method in this paper and justifying the application of FS in other, similar studies. Figures 27 and 28 present the tolerance diagram with respect to the train and test results of the RBF and ELM, respectively.

(a) After obtaining the best combination for the MPF neural network, it was necessary to check with one or two other neural networks whether the innovative hybrid network is working properly. In this study, RBF and ELM were employed to challenge the MPF results. Given that the best input parameters were obtained by the feature selection technique, trying different combinations at this stage was avoided and two combinations with four and seven inputs are used as per Table 11 . In addition, the neural network settings were as per Table 6 . Figure 26 demonstrates the regression charts of the ELM and RBF, in which the answers for both seven-and four-input models are accurate, indicating the efficiency of using the FS method in this paper and justifying the application of FS in other, similar studies. Figures 27 and 28 present the tolerance diagram with respect to the train and test results of the RBF and ELM, respectively. 

The present study aimed to predict the strength properties of a specific C-shaped shear connector at different heat stages. To this end, a new AI technique was developed to evaluate the results. Firstly, finite element (FE) analysis was applied by the ABAQUS program to model the composite floor system and simulate push-out tests at elevated temperatures. Then the results were collected, and a validated database was established. Secondly, a well-known neural network algorithm called multi-layer perceptron (MLP) was developed with the particle swarm optimization (PSO) technique to present a novel hybrid algorithm for evaluating the FE data. In addition, the feature selection (FS) method was used to avoid trying all possible input modes and wasting time while providing the best possible input combination, which may be neglected in other ways. Using the FS method facilitated the prediction process for the hybrid algorithm. In this regard, FE modelling was discussed by explaining the mechanical and geometrical properties of the composite model along with the validation procedure, and the results were presented. Next, the MLP-PSO-FS (MPF) methodology was developed. Then the AI results were interpreted and to verify the MPF results they were compared with the results of two wellknown algorithms, namely ELM and RBF. The dataset used consisted of 1010 rows of laboratory data including seven inputs, namely length (mm), fc (N/mm 2 ), channel-thickness (mm), profile-thickness (mm), height (mm), temperature (°C), and failure load (kN), while the slip (mm) was considered as the output. The MPF obtained the best results using the 

The present study aimed to predict the strength properties of a specific C-shaped shear connector at different heat stages. To this end, a new AI technique was developed to evaluate the results. Firstly, finite element (FE) analysis was applied by the ABAQUS program to model the composite floor system and simulate push-out tests at elevated temperatures. Then the results were collected, and a validated database was established. Secondly, a well-known neural network algorithm called multi-layer perceptron (MLP) was developed with the particle swarm optimization (PSO) technique to present a novel hybrid algorithm for evaluating the FE data. In addition, the feature selection (FS) method was used to avoid trying all possible input modes and wasting time while providing the best possible input combination, which may be neglected in other ways. Using the FS method facilitated the prediction process for the hybrid algorithm. In this regard, FE modelling was discussed by explaining the mechanical and geometrical properties of the composite model along with the validation procedure, and the results were presented. Next, the MLP-PSO-FS (MPF) methodology was developed. Then the AI results were interpreted and to verify the MPF results they were compared with the results of two well-known algorithms, namely ELM and RBF. The dataset used consisted of 1010 rows of laboratory data including seven inputs, namely length (mm), fc (N/mm 2 ), channel-thickness (mm), profile-thickness (mm), height (mm), temperature ( • C), and failure load (kN), while the slip (mm) was considered as the output. The MPF obtained the best results using the feature selection technique, which was followed by a description of each neural network. The most important results can be summarized as follows:

• Based on FE results, using longer channels could increase the ductility of the composite system at lower heats; however, at elevated temperatures, the stiffness of the composite system experiences a noticeable loss. • According to FS technique results, the failure load and temperature are the most effective inputs that can help to accurately predict slip value without using other inputs. Furthermore, concrete compressive strength and connector height are the two key parameters for a sustainable design of a composite floor system at elevated temperatures.

The combination of an MLP neural network with the PSO optimization algorithm based on a random population achieved the best results with excellent accuracy. The result of the MPF algorithm on the model with a combination of four inputs was the most precise prediction with RMSE = 13.072, r = 0.972 and R 2 = 0.945. • ELM and RBF were also applied on the main models (four and seven inputs) to predict slip value. Both had better performance on seven-input models with RMSE = 13.286, r = 0.969 and R 2 = 0.938 for ELM, and RMSE = 13.884, r = 0.969 and R 2 = 0.939 for RBF.

Finally, despite the rankings of these three algorithms, it should be noted that the results of all three networks performed very well in the prediction of slip value at elevated temperatures. However, combining PSO with MLP provided the best results. In the RBF and ELM models, the best results were obtained with seven inputs but, similar to the MLP-PSO, the results with four inputs were very acceptable. Performing cyclic loading on channel connectors could be considered as further study. In addition, other geometrical shapes and sizes could be developed to investigate their performance as stiffeners. 

A Novel Slip Sensory System for Interfacial Condition Monitoring of Steel-Concrete Composite Bridges

Analytical approach for crack identification of glass fiber reinforced polymer-sea sand concrete composite structures based on strain dissipations

Ameliorating strength-ductility efficiency of graphene nanoplatelet-reinforced aluminum composites via deformation-driven metallurgy

Shake Table Testing of Standard Cold-Formed Steel Storage Rack

Application of Extreme Learning Machine (ELM) and Genetic Programming (GP) to design steel-concrete composite floor systems at elevated temperatures

Experimental and informational modeling study on flexural strength of eco-friendly concrete incorporating coal waste

Mechanical Properties of Recycled Aggregate Concretes Containing Silica Fume and Steel Fibres

Insight on corrosion behavior of friction stir welded AA2219/AA2195 joints in astronautical engineering

Object traversing by monocular UAV in outdoor environment

Cost-effective mechanochemical synthesis of highly dispersed supported transition metal catalysts for hydrogen storage

Behaviour of Channel Shear Connectors: Push-Out Tests

Finite element modeling of FRP wrapped high strength concrete reinforced with axial and helical reinforcement

Fatigue reliability evaluation of aging prestressed concrete bridge accounting for stochastic traffic loading and resistance degradation

Renewable quantile regression for streaming datasets

Full-scale Tests of Channel Shear Connectors and Composite T-Beams

Fresh, mechanical, and durability properties of self-compacting mortar incorporating alumina nanoparticles and rice husk ash

Clayey soil stabilization using alkali-activated volcanic ash and slag

Secure consensus of multi-agent systems with redundant signal and communication interference via distributed dynamic event-triggered control

Numerical Analysis of Axial Cyclic Behavior of

Maximum probabilistic and dynamic traffic load effects on short-to-medium span bridges

On feasibility and limitations of detecting false data injection attacks on power grid state estimation using D-FACTS devices

Optimal design of broadband quasi-perfect sound absorption of composite hybrid porous metamaterial using TLBO algorithm

Design and study of a hybrid composite structure that improves electromagnetic shielding and sound absorption simultaneously

Annular acoustic black holes to reduce sound radiation from cylindrical shells

Transmission loss of plates with multiple embedded acoustic black holes using statistical modal energy distribution analysis

Properties of Lime-Cement Concrete Containing Various Amounts of Waste Tire Powder under Different Ground Moisture Conditions

Stabilization analysis for fuzzy systems with a switched sampled-data control

Experimental and numerical investigation of a method for strengthening cold-formed steel profiles in bending

Investigation of a method for strengthening perforated cold-formed steel profiles under compression loads

Integration of hydrogen storage system and wind generation in power systems under demand response program: A novel p-robust stochastic programming

Synchronization of Markovian complex networks with input mode delay and Markovian directed communication via distributed dynamic event-triggered control

Behaviour and design of shear connectors in composite slabs at elevated temperatures

Negative emotion arousal and altruism promoting of online public stigmatization on COVID-19 pandemic

System identification of a volumetric steel modular frame using experimental and numerical vibration analysis

Crack detection of concrete structures using deep convolutional neural networks optimized by enhanced chicken swarm algorithm

Behaviour of shear connectors in cold-formed steel sheeting at ambient and elevated temperatures. Thin-Walled Struct

Fire Resistance of Composite Slabs with Profiled Steel Sheet and of Composite Steel Concrete Beams

A novel low-damage and low-abrasive wear processing method of Cf/SiC ceramic matrix composites: Laser-induced ablation-assisted grinding

A rough set-based bio-inspired fault diagnosis method for electrical substations

Experiments on reverse-channel connections at elevated temperatures

Numerical analysis of channel connectors under fire and a comparison of performance with different types of shear connectors subjected to fire

Performance of Channel and Tee Types of Shear Connector in Composite Slab with Steel Decking at Elevated Temperature

Long term effect of operating loads on large monopile-supported offshore wind turbines in sand

Effect of plasma-activated water on the structure and in vitro digestibility of waxy and normal maize starches during heat-moisture treatment

Accessible tourism: A bibliometric review

Numerical and analytical study of ultimate capacity of steel plate shear walls with partial plate-column connection

Establishing a 3D aggregates database from X-ray CT scans of bulk concrete

Data-driven system parameter change detection for a chain-like uncertainties embedded structure

Modelling of reinforced concrete structures and composite structures with concrete strength degradation taken into consideration

Numerical Evaluation of the Upright Columns with Partial Reinforcement along with the Utilisation of Neural Networks with Combining Feature-Selection Method to Predict the Load and Displacement

Application Of The Western Art Form Based On Artificial Intelligence

Computer network routing configuration based on intelligent algorithm. Acta Electron. Malays. 2020, 4, 28-30

Evaluating the use of recycled concrete aggregate and pozzolanic additives in fiber-reinforced pervious concrete with industrial and recycled fibers

Intelligent Scheduling Method of Port Vehicles Based on Probability Information

Identification of factors and decision analysis of the level of modularization in building construction

Application of artificial intelligence to evaluate the fresh properties of self-consolidating concrete

Intelligent model-based integrity assessment of nonstationary mechanical system

Comparative analysis of artificial intelligence techniques for the prediction of infiltration process

A weighted corrective fuzzy reasoning spiking neural P system for fault diagnosis in power systems with variable topologies

A review of wind speed and wind power forecasting with deep neural networks

Utilizing Artificial Intelligence to Predict the Superplasticizer Demand of Self-Consolidating Concrete Incorporating Pumice, Slag, and Fly Ash Powders

Intelligent Retrieval System of Ship Fault Information Based on Big Data Analysis

Seismic response prediction of FRC rectangular columns using intelligent fuzzy-based hybrid metaheuristic techniques

Secure social internet of things based on post-quantum blockchain

A novel approach to predict shear strength of tilted angle connectors using artificial intelligence techniques

Application of a Hybrid Artificial Neural Network-Particle Swarm Optimization (ANN-PSO) Model in Behavior Prediction of Channel Shear Connectors Embedded in Normal and High-Strength Concrete

Review on the use of artificial intelligence to predict fire performance of construction materials and their flame retardancy

Performance of shear connectors at elevated temperatures-A review

Seismic collapse assessment of a hybrid cold-formed hot-rolled steel building

Novel results on nonfragile sampled-data exponential synchronization for delayed complex dynamical networks

Finite element analysis of hybrid cold-formed steel shear wall panels

Lateral behaviour of hybrid cold-formed and hot-rolled steel wall systems: Experimental investigation

Fast learning in networks of locally-tuned processing units

Similarities of LVQ and RBF learning-a survey of learning rules and the application to the classification of signals from high-resolution electrocardiography

Extreme learning machine: Theory and applications

We deeply acknowledge Taif University for supporting this research through Taif University Researchers Supporting Project number (TURSP-2020/231), Taif University, Taif, Saudi Arabia.

The authors declare no conflict of interest.